Contact Us â Official VEVOR SupportContact Us â Official VEVOR Support
User Manual for VEVOR models including: 7X12, 7X2, 7X12 Mini Metal Lathe, 7X12, Mini Metal Lathe, Metal Lathe, Lathe
File Info : application/pdf, 8 Pages, 311.78KB
DocumentDocumentTechnical Support and E-Warranty Certificate www.vevor.com/support MINI METAL LATHE USER MANUAL MODEL:7X12 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually Saving Half in comparison with the top major brands. MODEL:7X2 Mini Metal lathe (The picture is for reference only, please refer to the actual object) NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate www.vevor.com/support This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product. -1- Part List Part name Name MX-001 Headstock MX-002 Drive belt Cover MX-003 Machine Bed (Long) Mx-004 Longitudinal Slider(Big) MX-005 Tailstock MX-006 Cross Slider (Small) MX-007 Three Jaw Chunk MX-008 Turning Tool Clamping Jaw MX-009 Live Center Part name Name MX-010 Stabilizing Plate (Long) MX-011 Hand Wheel Handle MX-012 Turning Tool MX-013 Connection Piece MX-014 Single Hole Slot Nut MX-015 Dual Holes Slot Nut MX-016 Screw M4*6 MX-017 Screw M4*8 MX-018 Screw M4*14 -2- Assembly Diagram and Procedure Detailed Steps & Tips 1. Connect the headstock with long machine bed by connection pieces 2. Screw up the three jaw chuck to the main shaft of headstock 3. Install the tailstock & live center 4. Fix the big slider to long machine bed by two connection pieces 5. Place the small slider base on the top of big slider and fix it by M4*6 screws & single hole slot nuts 6. Small slider installation 7. Mount the turning tools 8. Screw up the long stabilizing plates 9. Install the drive belt cover 10. Add the handles to hand wheels -3- . Features and Technical Parameter 1. The mini metal lathe is mainly used for processing the outer & inner circles of the work piece,suitable for wood materials and soft metals (aluminum, copper, etc.) 2. The maximum diameter of processed materials is 50mm, length 150mm; three-jaw chuck: internal jaw 30mm, extra jaw 50mm 3. Small slider travels: 45mm, big slider travels: 145mm 4. Small Power Motor speed: 20,000 rpm, input voltage / current / power: 12V / 3A / 36W 5.High Power Motor speed: 12,000 rpm, input voltage / current / power: 12V / 5A / 60W . Mini Metal Lathe Operation 1. Firstly locate the center of work piece by center finder, Use 2 iron rods to unscrew the three-jaw chuck and place one end of the work piece into middle of the chuck. Tighten the chuck and rotate the hand wheel at the other end to push the live center into the center of the work piece tightly. And then, tighten the taikstock and fix the screw, so as to fix the work piece 2. Turn on the lathe,move the small slider in the Y axis direction to control the feed, move the big slider in the X axis direction to control the processing position Notes: 1. If the work pieces are not concentric and have imaginary circles, remove the outer imaginary circle 2. Tool setting: before processing, insert the turning tool into the turning tool clamping jaw and move the slider to adjust the turning tool into the same horizontal line with the live center & middle of three-jaw chunk . Maintenance and Repair 1. Daily maintenance: After using the machine tools, clean up the machine each time, and add some lubricant at the screw and slider position for the next use 2. FAQ: -4- No. Failure Cause Solution 1.Check the power input and output to confirm if power is on Not working 1.Not energized 2.Remove the belt cover,adjust the 1 after 2.Belt jammed tension of belt turing on 3.Motor damage 3.After confirm the motor is damaged,notify the factory for after-sales maintenance support Noise getting 2 Belt getting too tight Adjust the belt tension louder 1.Operation method 1.Use right operation method Difficult to 3 feed is wrong 2.Feed rate is too big 3.The woodturning 2.Adjust the feed rate,grinding by multiple times 3.Repair the woodturning tool by tool is blunt &worn sharpening When 1.The belt is processing, aged&broken it suddenly 4 become 2.Drive center becomes unable to cut loose or slipping &trim 1.Replace the belt 2.Remove the drive center fixing screw,reinstall the drive center or re-strike in the work piece -5- Warning-To reduce the risk of injury, user must read instructions manual carefully. This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 EC REP E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main. UK REP YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX -6- Technical Support and E-Warranty Certificate www.vevor.com/support