Intégration CRUX ACPGM-80N Smart-Play avec le manuel d'utilisation de plusieurs caméras
CRUX ACPGM-80N Smart-Play Integration with Multi Camera

CARACTÉRISTIQUES DU PRODUIT

  • Smart-Play Integration system allows connection of Android and other phones to the GM infotainment system.
  • Made for Android Auto and CarPlay.
  • Adds front and rear aftermarket camera inputs.
  • Retains functionality of the OEM backup camera if present.
  • Front camera automatically shows on the screen after changing the gear from reverse to drive.
  • Forcé view function for front and aftermarket rear camera.

PIÈCES INCLUSES

  • ACPGM-80N Module
    ACPGM-80N Module
  • Power Harnesses
    Power Harnesses
  • Smartphone Interface Module
    Smartphone Interface Module
  • Câble de rallonge USB
    Câble de rallonge USB
  • 4K Câble HDMI
    4K Câble HDMI
  • Microphone
    Microphone
  • LVDS Video Cable
    LVDS Video Cable
  • Câble auxiliaire 3.5 mm
    Câble auxiliaire 3.5 mm
  • Smart-Play Module Power Harness
    Smart-Play Module Power Harness
  • OSD Controller
    OSD Controller

SCHÉMA DE CÂBLAGE

SCHÉMA DE CÂBLAGE

RÉGLAGES DES COMMUTATEURS DIP

RÉGLAGES DES COMMUTATEURS DIP

DIP RÉGLAGE VÉHICULE
Entre 1 et 8 ALL UP Malibu and Volt
1 BAS Corvette C7
2 BAS Escalade, CTS-V
3 UP Pas de fonction
4 BAS Cruze (with 8” screen)
5 BAS Cadillac XT5
6 BAS Impala, Suburban, Tahoe, Yukon, Sierra, Acadia, Silverado, Yukon (with RSE)
7 BAS Suburban (with RSE), Tahoe (with RSE)
1 STATION DE DÉSINFECTION BLANCHE - 5 BOÎTE DE MOUSSE *AVEC POMPE (pompe ajustement par pression)* BAS Colorado
2 STATION DE DÉSINFECTION BLANCHE - 5 BOÎTE DE MOUSSE *AVEC POMPE (pompe ajustement par pression)* BAS Escalade, CTS, CTS-V, SRX (with no OEM front camera)

RSE = Rear Seat Entertainment

INSTRUCTIONS D'INSTALLATION

  • Suburban, Tahoe, Yukon models with Rear Seat Entertainment Systems have 2 LVDS cables on the back of the radio.
    INSTRUCTIONS D'INSTALLATION
  • Plug and play connections behind the top side of the radio.
    INSTRUCTIONS D'INSTALLATION
  • On RE models, the power harness is plugged in behind the headunit but the LVDS cable is plugged in at the HMI module (usually found behind the glove box).
    INSTRUCTIONS D'INSTALLATION
  • Connection is made on the blue LVDS connector on the HMI module.
    INSTRUCTIONS D'INSTALLATION

NOTE SPÉCIALE:

On Impala and Suburban, Tahoe, Yukon models with Rear Seat Entertainment Systems, the LVDS cable connection on the ACPGM-80N LVDS adapter board is the opposite of the standard connection. Please take note of this when plugging in the LVDS connectors. See image below.

LVDS cable connection

Cadillac and Corvette C7 with 10 pin Connector at headunit

For Cadillac and Corvette C7 installations, you must cut the ACPGM-80N 10 pin connectors and hardwire it to the OEM connector wires.

OEM connector wires

ACPGM-80N POWER HARNESS
Blanc LIN Bus
Bleu / Blanc MMI
Marron blanc CAN
Rouge +12V Constante
Noir Sol

Cadillac and Corvette C7 Connection with 10 Pin connector:

Connection with 10 Pin connector

  • PIN 1 = B+ connect to VCC Red wire
  • PIN 3 = CAN connect to CAN High (White/Brown) wire
  • PIN 8 = LIN (see connection diagram above)
  • PIN 10 = Ground connect to Black wire

Cut the Green wire on pin #8 on the 10 pin factory connector and connect the LIN (blue wire) and MMI (white wire) of the ACPGM-80N harness following the diagram above.

Cadillac Connection with 16 Pin connector:

16 Connecteur à broches

  • PIN 6 = LIN (see connection diagram above)
  • PIN 9 = B+ connect to VCC Red wire
  • PIN 12 = CAN connect to CAN High (White/Brown) wire
  • PIN 16 = Ground connect to Black wire

30 Pin ACPGM-80N main module pin out.

main module pin out
(Note: Wire colors can be different but pin locations will remain the same.

GM vehicles without Rear Seat Entertainment (RSE) wiring connections:

  • Plug and Play harness plugs behind radio
    Rear Seat Entertainment (RSE) wiring connections
  • ACPGM-80N LVDS video cable plugs behind radio
    Rear Seat Entertainment (RSE) wiring connections
  • LVDS Video Connection
    Rear Seat Entertainment (RSE) wiring connections
  • Plug in 4K HDMI Cable
    Rear Seat Entertainment (RSE) wiring connections
  • Plug in 3.5mm Aux Cable to factory Aux Input
    Rear Seat Entertainment (RSE) wiring connections
  • Plug in original smartphone cable to USB Ext. cable
    Rear Seat Entertainment (RSE) wiring connections

ON SCREEN DISPLAY (OSD) SETTINGS

The OSD Setting Screen automatically pops up when the OSD Control Pad is connected.

ON SCREEN DISPLAY (OSD) SETTINGS

Use the OSD menu to make the necessary settings. Remember to Run Save&Reboot after the settings are made. Unplug the OSD Control Pad after setting the cameras and keep it in a secure location in case it is needed to change the settings.

SMART-PLAY SETTING

  • After plugging in the OSD controller, navigate down to LVDS Input and set to ON. Push RIGHT button to go to the next menu.
    SMART-PLAY SETTING
  • Set Navi Brand to NV17
    SMART-PLAY SETTING
  • Navigate the OSD back the main menu and go to Save&Reboot then Run.
    SMART-PLAY SETTING

REAR AND FRONT CAMERA SETTING

REAR AND FRONT CAMERA SETTING

Dynamic Parking Guide Lines

Dynamic Parking Guide Lines

To turn ON the Dynamic Parking Guide Lines, go the Rear Input > Rear Set and turn ON Warning LANG. Go back to the root menu and Run Save&Reboot. Remember to unplug the OSD Control Pad otherwise the unit will not function properly. Set the parking brake on, start the car, put the gear in reverse, turn the steering wheel all the way to the left and all the way to right then put it in the center. The ACPGM-80N will calibrate automatically.

FRONT CAMERA SETTING

FRONT CAMERA SETTING

The front Camera will automatically show on the screen when the gear is put to Drive from Reverse. Set the delay time on the OSD menu. Delay time can be set from 1 to 60 seconds after a putting the car to drive from reverse.

FONCTIONNEMENT

  • To enter Smart-Play mode, press the upper left corner of the screen or double click the HOME button.
    Induction d'opération
  • Smart-Play home screen. Use the factory touch screen for Smart-Play controls.
    Induction d'opération
  • Apps can be opened by touch screen or by Siri control.
    Induction d'opération

OBLIGER VIEWING THE FRONT CAMERA

For MyLink IO5/IO6 radios:

Icône de la maison Press for 2 seconds = Force view front camera Press once = Back to OEM screen
Icône arrière Press for 2 seconds = Force view rear camera (only if aftermarket camera is used) Press once = Back to OEM screen

APPLICATIONS VÉHICULES

Compatible with 8” CUE or MyLink IO5/IO6 Systems.

Buick
2014-2018Cadillac
2013-2018
2014-2018
2014-2018
2014-2018
2015-2018
2013-2018
2013-2018
2016-2018
Lacrosse
ATS
CTS Coupe CTS
CTS-V
Escalade SRX
XTS XT5
Chevrolet
2014-2018
2017-2018
2015-2018
2015-2018
2014-2018
2015-2018
2014-2018
2015-2018
2015-2018
Avalanche Colorado Corvette Cruze Impala Malibu Silverado Suburban Tahoe GMC 2017-2018 2015-2018 2014-2018 2014-2018 Acadia Canyon Sierra Pickup Yukon

 

Documents / Ressources

CRUX ACPGM-80N Smart-Play Integration with Multi Camera [pdf] Manuel d'utilisation
ACPGM-80N, Smart-Play Integration, with MultiCamera, Integration

Références

Laissez un commentaire

Votre adresse email n'apparaitra pas.