Manuel d'utilisation du testeur de câbles réseau TESMEN TLP-900AR

1. Introduction

The TESMEN TLP-900AR is a multi-functional network cable tester designed for efficient wire maintenance and sorting. It combines cable tracing, line positioning, continuity testing, QC (Quality Control) for RJ45 crimping, and NCV (Non-Contact Voltage) detection. This device is suitable for various cable types including CAT5, CAT6, POE, shielded cables, and telephone lines, making it an essential tool for network engineers and technicians.

Image 1.1 : Terminéview of the TESMEN TLP-900AR Network Cable Tester and its multiple measurement functions.

2. Consignes de sécurité

• Veuillez toujours lire et comprendre ce manuel avant d'utiliser l'appareil.
• N’utilisez pas l’appareil s’il semble endommagé ou s’il ne fonctionne pas correctement.
• Exercise caution when using the NCV function, as it detects live voltage. Always assume wires are live until verified otherwise.
• For cable testing, it is recommended to disconnect power to avoid signal interference and ensure personal safety, especially when dealing with POE lines. The device is 60V resistant anti-burning, but caution is still advised.
• Ensure correct battery polarity when installing batteries. Use only specified 9V 6F22 batteries.
• Gardez l’appareil à l’abri de l’eau et des températures extrêmes.

Image 2.1: The TESMEN TLP-900AR features 60V resistant anti-burning protection for enhanced safety.

3. Contenu du colis

Vérifiez que tous les éléments énumérés ci-dessous sont inclus dans votre colis :

• 1 x TLP-900A Transmitter
• 1 x TLP-900R Receiver
• 1 x RJ45 Patch Cable
• 1 x RJ11 Patch Cable
• 1 x RJ11 Alligator Clip Adapter Cable
• 1 x boîte de rangement
• 1 x Manuel d'utilisation
• 2 x 9V 6F22 Batteries

Image 3.1: All components included in the TESMEN TLP-900AR Network Cable Tester kit.

4. Produit terminéview

The TLP-900AR consists of two main units: the TLP-900A Transmitter and the TLP-900R Receiver. Familiarize yourself with the buttons, ports, and indicators on each unit.

4.1. TLP-900A Transmitter

• Port RJ45: Pour connecter les câbles réseau.
• Port RJ11: Pour le raccordement des lignes téléphoniques.
• QC Port: For RJ45 crystal head crimping inspection.
• Function Button (FUNC): Toggles between scan, pair, and telephone line status modes.
• Bouton d'alimentation : Allume/éteint l'émetteur.
• Indicateurs : Cable Scan, Wire Mapping, Telephone Line Status, Crimping, Line Sequence, Shielded, POE, Power.

4.2. TLP-900R Receiver

• Sonde inductive : For tracing cables.
• Bouton de réglage de la sensibilité : Ajuste la sensibilité de détection.
• Scan Button/Indicator: Activates cable scan mode.
• Bouton NCV : Active le vol sans contacttage détection.
• Lamp: Built-in LED light for illuminating dark areas.
• Port RJ11: Pour le raccordement des lignes téléphoniques.
• Indicateurs : Sensitivity, Power, Pair.

Image 4.1: Product buttons and ports on the TESMEN TLP-900AR units.

5. Installation

5.1. Installation de la batterie

Both the TLP-900A Transmitter and TLP-900R Receiver require one 9V 6F22 battery each. Two batteries are included in the package.

1. Repérez le couvercle du compartiment à piles à l'arrière de chaque appareil.
2. Faites glisser ou déclipsez le couvercle pour ouvrir le compartiment.
3. Insert a 9V battery, ensuring the correct polarity (+ and - terminals match the markings inside the compartment).
4. Fermez soigneusement le couvercle du compartiment à piles.

Image 5.1: Proper installation of the 9V battery.

6. Mode d'emploi

6.1. Cable Scan (Tracing)

This function helps locate specific cables within bundles, behind walls, or under carpets.

1. Connect one end of the cable to be traced to the RJ45 or RJ11 port on the TLP-900A Transmitter.
2. Turn on the Transmitter by pressing its Power Button. Press the FUNC button until the 'SCAN' indicator is lit.
3. Turn on the TLP-900R Receiver.
4. Adjust the Sensitivity Adjustment Knob on the Receiver to an appropriate level. Higher sensitivity allows for faster detection over longer distances, while lower sensitivity provides more precise pinpointing.
5. Move the Receiver's inductive probe along the suspected path of the cable. The Receiver will emit an audible tone and its Sensitivity Indicator will light up when it detects the signal from the Transmitter. The frequency of the tone increases as you get closer to the cable.

Image 6.1: Cable scan in progress, tracing UTP/STP/POE cables.

The TLP-900AR features digital signal transmission for strong, anti-jamming performance, ensuring more accurate line finding. It can scan cables even when connected to PoE switches, routers, PCs, and other powered-on devices (up to DC 60V withstand voltaget).

Image 6.2: Scanning cables connected to a PoE switch.

6.2. Cable Fault Testing (Continuity & Pairing)

This function identifies common cable faults such as short circuits, open circuits, and crossovers.

1. Connect one end of the network cable to the RJ45 port on the TLP-900A Transmitter.
2. Connect the other end of the cable to the RJ45 port on the TLP-900R Receiver (or the remote unit if using a remote identifier, though not explicitly included in this model's description, the pairing function implies a remote end).
3. Turn on the Transmitter and press the FUNC button until the 'PAIR' indicator is lit.
4. Observe the LED indicators on both the Transmitter and Receiver. The sequence of lit LEDs will indicate the cable's wiring status.
5. Court-circuit: If two or more LEDs light up simultaneously, it indicates a short circuit between those wires.
6. Circuit ouvert: If an LED fails to light up in sequence, it indicates an open circuit (break) in that wire.
7. Croisement : If the LED sequence on the Receiver does not match the Transmitter, it indicates a crossover fault.

Image 6.3: Visual representation of cable fault detection.

6.3. QC RJ45 Crimp Inspection

The TLP-900A Transmitter can quickly inspect the quality of RJ45 crystal head crimping.

1. Insert a crimped RJ45 crystal head into the 'QC' port on the TLP-900A Transmitter.
2. The QC indicator will provide immediate feedback. A green light typically indicates a good crimp, while a red light or no light indicates an abnormal or faulty crimp.

Image 6.4: Performing a QC test on an RJ45 connector.

6.4. NCV (Vol sans contacttage) Function

The TLP-900R Receiver includes an NCV function to detect live AC voltaget sans contact direct, ce qui renforce la sécurité.

1. Turn on the TLP-900R Receiver.
2. Press the 'NCV' button to activate the function.
3. Move the tip of the Receiver near electrical outlets, wires, or other potential AC voltage sources.
4. The NCV indicator and an audible alert will activate when live voltage est détecté.

Image 6.5: Using the NCV function to detect live voltage.

6.5. Telephone Line Polarity Detection

The TLP-900R Receiver can identify the state of a telephone line.

1. Connect the telephone line to the RJ11 port on the TLP-900R Receiver.
2. The Receiver will indicate the polarity and state of the line (e.g., standby, off-hook, ringing).

Image 6.6: The TLP-900AR can detect telephone line status.

6.6. Sensibilité réglable

The TLP-900R Receiver features an adjustable sensitivity knob to optimize cable tracing.

• Rotation dans le sens des aiguilles d'une montre : Increases sensitivity for faster cable locating, especially over longer distances or through obstacles.
• Rotation dans le sens inverse des aiguilles d'une montre : Decreases sensitivity for more precise pinpointing of a specific cable in a dense bundle.

Image 6.7: Adjusting the sensitivity of the received signal.

6.7. Lumière LED intégrée

The TLP-900R Receiver is equipped with a built-in LED light to illuminate dark working environments, such as server racks or behind furniture.

1. Appuyez sur le « L »amp' button on the Receiver to turn the LED light on or off.

Image 6.8: Using the built-in LED light in a dark workspace.

7. Entretien

• Arrêt automatique: The device will automatically shut down after more than 30 minutes of inactivity to conserve battery life.
• Indicateur de batterie faible : The power indicator will flash when the battery level is too low for normal operation. Replace batteries promptly.
• Nettoyage: Essuyez l'appareil avec un chiffon doux et sec. N'utilisez pas de nettoyants abrasifs ni de solvants.
• Stockage: Store the device in its provided storage box in a cool, dry place when not in use. Remove batteries if storing for extended periods to prevent leakage.

8. Dépannage

• No signal during cable scan:
  • Assurez-vous que l'émetteur et le récepteur sont tous deux sous tension.
  • Check battery levels in both units.
  • Verify the cable is properly connected to the Transmitter.
  • Adjust the Receiver's sensitivity.
• Incorrect fault detection during continuity test:
  • Ensure the cable is fully inserted into both the Transmitter and Receiver.
  • Confirm the cable type matches the test being performed.
  • Inspect the RJ45/RJ11 connectors for damage.
• Voyant de batterie faible clignotant :
  • Replace the 9V batteries in the affected unit(s).

9. Spécifications

10. Garantie et assistance

TESMEN products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please contact TESMEN customer support.

E-mail du fabricant : support@tesmen.com