OBO HANDS GYS Electronic Smart Lock User Manual

1. Introduction

Thank you for choosing the OBO HANDS GYS Electronic Smart Lock. This manual provides detailed instructions for the installation, operation, and maintenance of your smart lock. Please read this manual thoroughly before installation and use to ensure proper function and security.

2. Produit terminéview

2.1 Principales caractéristiques

• Plusieurs méthodes de déverrouillage : Supports Fingerprint, RFID Card, PIN Code, Mechanical Key, and WeChat applet unlocking.
• Virtual Password Function: Enhances security by allowing random digits before and after the actual password.
• Administrator Management: Centralized control for managing user access.
• Alimentation de secours : USB interface for temporary power using a power bank in case of battery depletion.
• Rappel de batterie faible: Alerts when battery power is low (below 4.8V).
• Haute capacité : Stores up to 100 fingerprints, 100 passwords, and 100 cards.

2.2 Unlocking Methods Overview

Figure 1 : Plusview of available unlocking methods for the smart lock.

2.3 Composants internes

Figure 2: Internal components of the smart lock, including the battery compartment for 4 AAA batteries, circuit board, and various interfaces.

3. Configuration et installation

3.1 Vérifications avant l'installation

Avant de commencer l'installation, assurez-vous que votre porte répond aux exigences suivantes :

• The door may require an additional small hole to be drilled.
• Measure the door's thickness.
• Measure the length of the guide plate.
• Measure the width of the guide plate.
• The lock is compatible with exterior wooden doors where keyed entry is standard.

3.2 étapes d'installation

Installation typically takes approximately 20 minutes with a screwdriver and a drill. Follow the detailed instructions provided in the included installation guide (not part of this document) for precise steps. The general process involves:

1. Prepare the door by drilling necessary holes according to the template.
2. Installez la serrure à mortaise dans le chant de la porte.
3. Mount the front and rear panels of the smart lock.
4. Connect the internal wiring.
5. Installez les piles.
6. Tester le fonctionnement de la serrure.

Figure 3: Visual guide for smart lock installation and door preparation.

3.3 Configuration initiale

After physical installation, the lock requires initial configuration:

• Set Administrator: The first user registered (fingerprint, password, or card) will typically be designated as the administrator. This user has privileges to add or delete other users.
• Ajouter des utilisateurs : Follow the on-screen prompts or voice guidance to add additional fingerprints, PIN codes, or RFID cards for other users.

4. Mode d'emploi

4.1 Déverrouillage avec empreinte digitale

Place your registered finger flat on the fingerprint sensor. The lock will unlock if the fingerprint is recognized.

Figure 4: Fingerprint recognition area on the smart lock.

4.2 Unlocking with PIN Code (Virtual Password)

To use the virtual password function, enter any random digits before and after your actual PIN code. This prevents others from observing your correct code.

• Example: If your correct PIN is 123456, vous pouvez entrer 0000 + 123456 + 0000 to unlock the door. The lock will identify the correct sequence within the longer input.

Figure 5: Virtual password input method for enhanced security.

4.3 Déverrouillage par carte RFID

Present a registered RFID card to the card reader area on the lock. The lock will unlock upon successful recognition.

4.4 Déverrouillage avec une clé mécanique

In case of electronic failure or battery depletion, insert the mechanical key into the hidden keyhole and turn to unlock the door manually.

4.5 Unlocking with WeChat Applet

Refer to the specific instructions for connecting and operating the lock via the WeChat applet, usually found within the app itself after pairing.

4.6 Gestion des utilisateurs

Access the administrator menu (typically by entering the administrator PIN or fingerprint) to add, modify, or delete user fingerprints, PIN codes, and RFID cards. Consult the full installation guide for specific menu navigation steps.

5. Entretien

5.1 Remplacement de la batterie et alimentation de secours

The lock is powered by 4x AA batteries (not included). A low battery reminder will activate when the voltage drops below 4.8V. Replace batteries promptly when this occurs.

• Type de batterie : 4 x AA Batteries.
• Alimentation de secours: If batteries are completely depleted, connect a power bank to the emergency USB charging port on the lock to temporarily power it and gain access.

Figure 6: Emergency USB charging port and low battery alarm feature.

5.2 Nettoyage

Essuyez l'extérieur de la serrure avec un chiffon doux et sec. Évitez d'utiliser des nettoyants abrasifs ou des solvants qui pourraient endommager la finition ou les composants électroniques.

6. Dépannage

• La serrure ne répond pas : Check battery level. If low, replace batteries or use emergency USB power. Ensure no obstructions are preventing the bolt from moving.
• Empreinte digitale non reconnue : Assurez-vous que votre doigt est propre et sec. Si le problème persiste, essayez de réenregistrer votre empreinte digitale.
• Code PIN non fonctionnel : Verify the correct PIN is being entered. Ensure the virtual password sequence is correctly applied.
• Carte RFID non reconnue : Vérifiez que la carte est correctement enregistrée. Essayez de la réenregistrer.
• Lock beeps continuously: This may indicate a low battery or a system error. Check battery first. If the issue persists, perform a factory reset (refer to the full installation guide for reset procedures).

7. Spécifications

Figure 7: Dimensional drawing of the smart lock components.

8. Garantie et assistance

8.1 Informations sur la garantie

Please refer to your purchase documentation or contact the seller directly for specific warranty terms and conditions applicable to your OBO HANDS GYS Electronic Smart Lock.

8.2 Assistance clientèle

For any questions, technical assistance, or issues, please contact OBO HANDS customer service:

• WhatsApp: +86 177 2255 8183
• Disponibilité: Du lundi au dimanche, 24h/24 et 7j/7