1. Introduction
This manual provides detailed instructions for the safe and efficient operation of your ATOMSTACK A12 Pro Laser Engraving Machine. Please read this manual thoroughly before use to ensure proper setup, operation, and maintenance. Keep this manual for future reference.
Avertissements de sécurité :
- Always wear UV-filtering eye protection when operating the laser engraver.
- Ensure proper ventilation to dissipate fumes and smoke generated during engraving/cutting.
- Ne laissez pas la machine sans surveillance pendant son fonctionnement.
- Gardez les matériaux inflammables loin de la zone de travail.
- Familiarisez-vous avec l'emplacement du bouton d'arrêt d'urgence.
2. Contenu du colis
Vérifiez que tous les éléments énumérés ci-dessous sont inclus dans votre colis :
Figure 2.1: ATOMSTACK A12 Pro Laser Engraving Machine and included accessories.
- ATOMSTACK A12 Pro Laser Engraving Machine (Unibody Frame)
- Tête laser
- Adaptateur secteur (24 V, 5 A)
- Câble d'alimentation
- Câble USB (Type-C)
- Goggles (UV-filtering eye protection)
- Fixed Focus Lens
- Manuel d'utilisation
- Tools (H3 hexagon L-shaped wrench, M4 thumb screws)
- Clé USB
- Antenne WiFi
- Silicone Hose (air hose)
- Wire Anchor
- Câble Clamp
- 100*30 lint free cloth
- Curseur
- Touche de commutation
3. Guide de configuration
The ATOMSTACK A12 Pro features an unibody design for minimal assembly. Follow these steps to get started:
- Déballage : Carefully remove the machine and all accessories from the packaging. The machine is pre-calibrated and shipped as a single unit.
Figure 3.1: The ATOMSTACK A12 Pro is ready to use right out of the box with its unibody design.
- Installez le curseur : Attach the slider component to the designated rail on the machine. Secure it with the provided screws.
- Installer la tête laser : Mount the laser head onto the slider. Ensure it is firmly attached.
- Installez l'antenne WiFi : Screw the WiFi antenna into its port on the machine's side.
- Installation des tubes et des lignes de liaison de l'axe X : Connect the tubing and X-axis link lines as shown in the diagram to ensure proper cable management and operation.
- Connectez l'alimentation et l'USB : Plug the power adapter into the machine and a power outlet. Connect the USB cable from the machine to your computer.
- Mise sous tension : Insert the switch key and turn it to the ON position. The machine is now ready for software setup.
Video 3.1: A detailed guide on how to install and set up the ATOMSTACK laser engraver.
4. Mode d'emploi
4.1 Contrôle logiciel
The ATOMSTACK A12 Pro supports multiple control methods:
- ATOMSTACK PC Software: Exclusive software for simplified operation, ideal for beginners.
- LightBurn et LaserGRBL : Traditional PC software for advanced users.
- ATOMSTACK Mobile APP: Available on Android and Apple App Stores for WiFi control via smartphone.
Figure 4.1 : Plusview of the various software and app control options for the laser engraver.
4.2 Procédé de gravure
- Emplacement du matériel : Place your material flat on the engraving bed.
- Réglage de la mise au point : Use the fixed-focus design for rapid and precise focusing in approximately 10 seconds.
- Cross Positioning: Utilize the newly added cross laser positioning feature for clear visibility of the laser's location, ensuring perfect alignment for engraving and easy horizontal adjustment.
- Paramètres du logiciel : Adjust engraving parameters (speed, power, passes) in your chosen software based on the material.
- Commencer la gravure : Lancez le processus de gravure depuis le logiciel.
Figure 4.2: The cross positioning system helps align objects and lock to edges for precise horizontal carving.
5. Caractéristiques et capacités
- Conception monocoque : Sturdy all-aluminum unibody design, installation-free and pre-calibrated.
- Haute vitesse et précision : New dual-axis linear guide rail structure and high-speed motherboard allow engraving speeds up to 600mm/s, 3-6 times faster than traditional frame machines. Accuracy within 0.004 inches.
- Laser puissant : 12000mW diode laser (Laser Class 4) with 50W machine power and a 0.05*0.06mm ultra-fine laser spot focus.
- Thicker Cuts: Can cut through 8mm wood, 5mm black acrylic, and 0.02mm stainless steel in a single pass.
- Diverse Material Compatibility: Engraves and cuts a wide range of materials including wood, acrylic, metal, glass, ceramics, leather, paper, cardboard, and more.
- Automatic Power Failure Recovery: Memorizes engraving position and swiftly resumes from the paused point, ensuring uninterrupted production and material saving.
- Sécurité renforcée : Equipped with 4-way limit switches, UV-filtering eye protection, a tilt detector with a 15-degree alarm, and an emergency stop button.
Figure 5.1: Comparison showing the significantly faster engraving speed of the A12 Pro.
Figure 5.2: Demonstrates the maximum cutting thickness for various materials with the A12 Pro.
Figure 5.3 : Examples of various materials that can be engraved or cut by the machine.
6. Entretien
- Nettoyage des lentilles : Regularly clean the laser lens with the provided lint-free cloth to maintain optimal performance and prevent residue buildup.
- Lubrification des rails : Periodically apply a small amount of lubricant to the guide rails to ensure smooth movement of the laser head.
- L'enlèvement des débris: Keep the engraving bed and surrounding area free of debris and dust. Use an air compressor or brush to clear away small particles.
- Mises à jour du micrologiciel : Consultez le site officiel d'ATOMSTACK. website periodically for firmware updates to ensure your machine has the latest features and bug fixes.
7. Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| La machine ne s'allume pas | Power cable loose; Emergency stop engaged; Key not turned. | Check power connections; Disengage emergency stop; Turn key to ON. |
| Laser non fonctionnel/faible puissance | Lens dirty; Incorrect focus; Low power setting in software. | Clean laser lens; Adjust focus; Increase power setting. |
| Engraving is distorted/inaccurate | Loose belts/rails; Material shifting; Incorrect software settings. | Check and tighten belts/rails; Secure material; Verify software settings. |
| Le logiciel ne se connecte pas à la machine. | Problème de câble USB ; pilote non installé ; port COM incorrect. | Try different USB port/cable; Install drivers; Select correct COM port in software. |
8. Spécifications
- Dimensions du produit : 23.22 x 23.22 x 7.08 pouces
- Poids de l'article : 18.74 livres
- Puissance de sortie du laser : 12000mW (12W)
- Puissance de la machine : 50 W
- Taille du point laser : 0.05*0.06mm
- Vitesse de gravure : Jusqu'à 600 mm/s
- Précision: Within 0.004 inches
- Connectivité : USB, WiFi (via Mobile APP)
- Logiciels pris en charge : ATOMSTACK PC Software, LightBurn, LaserGRBL
- Fabricant: Shenzhen AtomStack Technologies Co., Ltd.
- Pays d'origine : Chine
9. Garantie et assistance
Your ATOMSTACK A12 Pro Laser Engraving Machine comes with a standard manufacturer's warranty. For detailed warranty information, technical support, or service inquiries, please refer to the warranty card included in your package or visit the official ATOMSTACK website.
Our professional technical and support teams are available 24/7 to answer any questions or concerns you may have.