Produit terminéview
The Thermalright Aqua Elite 120 V3 is an all-in-one liquid CPU cooler designed for efficient heat dissipation. It features a fourth-generation pump head, a 120mm aluminum fin heat sink, protective mesh water pipes, and a 120mm ARGB fan. This cooler is engineered for low vibration, high heat dissipation, and extended lifespan, providing optimal cooling performance for your CPU.
Image: Thermalright Aqua Elite 120 V3 ARGB All-in-one CPU Liquid Cooler components.
Contenu du colis
Avant de commencer l'installation, assurez-vous que tous les composants sont présents :
- Liquid CPU Cooler (Radiator, Pump, Fans, Tubing)
- Matériel de montage pour AMD (AM4/AM5)
- Mounting hardware for Intel (LGA1150/1151/1155/1156/1200/2011/2066/1700)
- Pâte thermique
- Manuel de l'utilisateur (ce document)
Image: Close-up of the Thermalright Aqua Elite 120 V3 cooler highlighting ARGB lighting and design features.
Configuration et installation
Follow these steps carefully to install your Thermalright Aqua Elite 120 V3 Liquid CPU Cooler. Refer to the official installation video for visual guidance.
1. Préparer la carte mère
For AMD AM5 and AM4 motherboards: Remove the motherboard's plastic brackets around the CPU socket. Keep the original backplate as it will be reused.
For Intel LGA1700 motherboards: Use the outer mounting holes on the Intel backplate. Assemble the Intel backplate by using blue washers to fix the backplate screws. Install the assembled Intel backplate from the back side of the motherboard, ensuring backplate screws pass through the motherboard mounting holes. Install four blue standoffs onto the backplate screws. Install two Intel brackets onto the standoffs, aligning the LGA1700 holes on the brackets. Secure the brackets with nuts using a screwdriver.
Common Procedure: Apply thermal compound onto the CPU Integrated Heat Spreader (IHS). Remove the coldplate protective sticker from the waterblock. Place the waterblock onto the CPU, ensuring the waterblock bracket nuts align with the screws on the brackets. Tighten the nuts to secure the waterblock.
2. Connectez les câbles
- Connect the fan PWM power cable to sync fan speed.
- Connect the fan ARGB cable to sync lighting signal.
- Connect the fan PWM power cable to the CPU_FAN socket on your motherboard.
- Connect the waterblock 4-pin PWM header to the motherboard's CPU_OPT or WATER_PUMP socket to power the water pump.
- Connect the ARGB lighting cable to a 3-pin 5V ARGB socket on your motherboard for lighting control.
Video: Official Thermalright Aqua Elite 120 V3 Liquid CPU Cooler installation guide. This video demonstrates the step-by-step process for mounting the cooler on both AMD and Intel platforms, applying thermal paste, and connecting the necessary cables for power and ARGB lighting synchronization.
Mode d'emploi
The Thermalright Aqua Elite 120 V3 is designed for automatic operation once correctly installed and connected.
- Contrôle du ventilateur par modulation de largeur d'impulsion (PWM) : The included TL-C12B-S V2 fan features PWM (Pulse Width Modulation) functionality, allowing it to automatically adjust its speed based on CPU temperature. This ensures optimal cooling performance while minimizing noise levels.
- Éclairage ARGB : The fan and pump head feature Addressable RGB (ARGB) lighting. If connected to a compatible 5V/3PIN ARGB motherboard header, the lighting can be controlled and synchronized using your motherboard's software. This allows for customization of lighting effects and colors.
- Efficient Pump Operation: The fourth-generation pump head operates at up to 3,300 RPM ± 10%, ensuring consistent and efficient coolant circulation for effective heat transfer away from the CPU.
Image: The octagonal water pump head with ARGB lighting and pump speed details.
Image: Details of the TL-C12B-S V2 fan, highlighting PWM control, S-FDB bearing, and shock-absorbing pads for quiet operation.
Entretien
Un entretien régulier contribue à assurer la longévité et les performances optimales de votre système de refroidissement liquide pour processeur.
- Nettoyage de la poussière : Nettoyez régulièrement la poussière accumulée sur les ailettes du radiateur et les pales du ventilateur à l'aide d'air comprimé ou d'une brosse douce. Assurez-vous que le système est hors tension avant tout nettoyage.
- Inspection des tubes : Inspect the water pipes for any signs of wear, kinks, or leaks. While the pipes are designed for low evaporation and high lifespan, regular checks are recommended.
- Composé thermique : The thermal compound typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal compound.
Dépannage
If you encounter issues with your Thermalright Aqua Elite 120 V3, refer to the following common troubleshooting tips:
- Températures élevées du processeur :
- Ensure the waterblock is securely mounted to the CPU and thermal compound is properly applied.
- Check if the fans are spinning correctly and not obstructed.
- Verify that the pump is receiving power and operating (listen for a faint hum or feel for vibrations in the tubing).
- Assurez une circulation d'air adéquate à l'intérieur de votre boîtier PC.
- Bruit excessif :
- Check fan blades for obstructions or loose mounting.
- The S-FDB bearing in the fans is designed for low noise; however, ensure fan screws are tight.
- Pump noise can occur if air is trapped in the loop. Gently tilt your PC case to help dislodge air bubbles.
- L'éclairage ARGB ne fonctionne pas :
- Verify that the ARGB cable is correctly connected to a 3-pin 5V ARGB header on your motherboard.
- Check your motherboard's ARGB software to ensure lighting is enabled and configured.
- Ensure the ARGB header on the motherboard is enabled in the BIOS/UEFI settings if applicable.
- Pompe défectueuse :
- Confirm the 4-pin PWM header from the waterblock is securely connected to the CPU_OPT or WATER_PUMP header on the motherboard.
- Check motherboard BIOS/UEFI settings to ensure the pump header is configured correctly and receiving power.
Caractéristiques
| Fonctionnalité | Spécification |
|---|---|
| Dimensions du bloc d'eau | 61.7 mm x 61.7 mm x 53.8 mm |
| Dimensions du radiateur | 157 mm x 120 mm x 27 mm |
| Bruit de pompe à eau | ≤23 dBA |
| Vitesse de la pompe à eau | 3300 tr/min ± 10% |
| Courant nominal de la pompe | 0.40A ± 10% |
| Puissance nominale de la pompe | ≤4.8W |
| Palier de pompe | Roulement céramique |
| Connecteur de pompe | PWM 4 broches |
| Support d'éclairage pour waterblock | RGB adressable +5V |
| Dimensions du ventilateur | 120 mm x 120 mm x 25 mm |
| Vitesse nominale du ventilateur | 1500 tr/min ± 10% |
| Bruit du ventilateur | ≤25.6 dBA |
| Débit d'air du ventilateur | 66.17 CFM (MAX) |
| Pression statique du ventilateur | 1.53 mm/H₂O (MAX) |
| Connecteur du ventilateur | PWM 4 broches |
| Volume nominal du ventilateurtage | 12 V CC |
| Courant nominal du ventilateur | 0.20A (MAXIMUM) |
| Type de roulement de ventilateur | Roulement S-FDB |
Garantie et assistance
Les produits Thermalright sont fabriqués selon des normes de qualité élevées. Pour toute information concernant la garantie, l'assistance technique ou le service après-vente, veuillez consulter le site officiel de Thermalright. webConsultez leur site web ou contactez directement leur service client. Conservez votre reçu d'achat pour toute réclamation au titre de la garantie.