Klarstein Beretta Island Exhaust Hood

Introduction

Thank you for choosing the Klarstein Beretta Island Exhaust Hood. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new appliance. Please read this manual thoroughly before use and keep it for future reference.

The Klarstein Beretta Island Exhaust Hood is designed to effectively remove steam, grease, and odors from your kitchen, ensuring a clean and fresh cooking environment. Its elegant design makes it a centerpiece for any modern kitchen island setup.

Consignes de sécurité

AVERTISSEMENT : Le non-respect de ces consignes de sécurité peut entraîner un incendie, une électrocution ou des blessures.

• Assurer l'alimentation voltage correspond à l'étiquette de puissance figurant sur l'appareil.
• Cet appareil est destiné à un usage domestique uniquement. Ne pas utiliser à des fins commerciales.
• Débranchez toujours l'appareil de l'alimentation électrique avant le nettoyage ou l'entretien.
• Ne pas flamber sous la hotte.
• L'air évacué ne doit pas être évacué dans un conduit utilisé pour évacuer les fumées des appareils brûlant du gaz ou d'autres combustibles.
• Nettoyez régulièrement les filtres à graisse pour éviter les risques d'incendie.
• L'installation doit être effectuée par une personne qualifiée, conformément à toutes les réglementations et normes locales.
• Assurez une ventilation adéquate de la pièce lorsque la hotte aspirante est utilisée simultanément avec des appareils à gaz ou à combustion d'autres combustibles.
• Tenez les enfants éloignés de l'appareil pendant son fonctionnement et son nettoyage.

Produit terminéview

The Klarstein Beretta Island Exhaust Hood is a high-performance appliance designed for ceiling mounting over freestanding hobs. It features a powerful motor, efficient filtration system, and user-friendly controls.

Caractéristiques principales :

• Circulation d'air puissante : Maximum air circulation up to 650 m³/h.
• Filtration efficace : Washable aluminum grease filter and activated carbon filters for odor removal.
• Utilisation facile : Intuitive push-button control panel with LED lighting.
• Éclairage intégré : Switchable LED hob lighting (2 x 1 watt) for clear visibility.
• Modes polyvalents : Suitable for both extraction (ducted) and recirculation (ductless) operation.
• Efficacité énergétique : Energy efficiency class C.

Composants inclus :

• 1 x Extractor Hood Unit
• 1 x Chimney Cover
• 3 x Ceiling Mounting Brackets
• 6 x supports de montage
• 1 x Connecting Plate
• 1 x Check Valve (2-piece)
• 1 x tuyau d'échappement
• 1 x Mounting Material (screws and dowels)
• 1 x gabarit de perçage
• 2 filtres à charbon actif

Figure 1: Klarstein Beretta Island Exhaust Hood (copper) and activated carbon filters.

Figure 2: Control panel with LED illumination. The buttons control power, fan speed, and lighting.

Configuration et installation

The Klarstein Beretta Island Exhaust Hood is designed for ceiling mounting. Due to the complexity and safety requirements, professional installation is highly recommended. Ensure you have all necessary tools and assistance before beginning the installation process.

Liste de contrôle de pré-installation :

• Verify all components listed in the "Components Included" section are present.
• Ensure the ceiling structure is strong enough to support the weight of the hood (approx. 9.4 kg for hood, 5.7 kg for chimney cover).
• Confirm the availability of a suitable electrical outlet (220-240 V ~ | 50 Hz).
• Decide between extraction (ducted) or recirculation (ductless) mode. For extraction, ensure proper ducting is available.

Étapes d'installation (Résumé) :

1. Marquage: Use the provided drill template to accurately mark the drilling points on the ceiling for the mounting brackets.
2. Supports de montage : Securely attach the ceiling mounting brackets using the supplied screws and dowels.
3. Assemblage du capot : Assemble the main hood unit and attach the connecting plate and check valve if using extraction mode.
4. Conduits (le cas échéant) : Connect the exhaust hose to the hood and route it to the exterior vent.
5. Connexion électrique : Connect the hood to the power supply. This step should be performed by a qualified electrician.
6. Montage du capot : Carefully lift and secure the hood onto the ceiling mounting brackets.
7. Chimney Cover: Install the chimney cover, ensuring it aligns properly with the hood.
8. Installation du filtre: Install the aluminum grease filter and activated carbon filters (for recirculation mode).

Note: The detailed installation instructions, including diagrams, are provided in the multilingual manual included with your product.

Figure 3 : Example of the exhaust hood installed in a kitchen island setting.

Figure 4: All included components for installation and operation.

Mode d'emploi

The Klarstein Beretta Island Exhaust Hood features a user-friendly push-button control panel located on the front of the hood.

Fonctions du panneau de contrôle :

• Bouton d'alimentation (Marche/Arrêt) : Appuyez pour allumer ou éteindre le capot.
• Boutons de vitesse du ventilateur (1, 2, 3) : Select one of the three available fan speeds to adjust the extraction power according to your cooking needs.
  • Vitesse 1 : Vitesse lente pour une cuisson légère ou à feu doux.
  • Vitesse 2 : Vitesse moyenne pour la cuisson en général.
  • Vitesse 3 : Vitesse élevée pour la friture intensive ou les odeurs fortes.
• Bouton lumineux : Press to turn the integrated LED hob lighting on or off. The lighting provides clear visibility over your cooking area.

Conseils d'utilisation :

• Turn on the hood a few minutes before you start cooking to create an air current.
• Allow the hood to operate for 5-10 minutes after cooking to clear any remaining steam or odors.
• For optimal performance, ensure windows and doors are not creating strong drafts that could interfere with the hood's suction.

Figure 5: The hood effectively extracting steam during cooking.

Entretien et nettoyage

Regular maintenance ensures the longevity and optimal performance of your Klarstein Beretta Island Exhaust Hood. Always disconnect the appliance from the power supply before performing any cleaning or maintenance.

Nettoyage du filtre à graisse :

The aluminum grease filter should be cleaned regularly, depending on usage (typically every 2-4 weeks). A dirty filter can reduce suction power and pose a fire risk.

1. Open the filter clips and remove the aluminum grease filter from the hood.
2. Wash the filter by hand in hot soapy water or in a dishwasher (use a mild detergent and low temperature cycle).
3. Rincez abondamment et laissez le filtre sécher complètement avant de le réinstaller.
4. Re-install the dry filter, ensuring it clicks securely into place.

Replacing the Activated Carbon Filter (for Recirculation Mode):

Activated carbon filters are used for odor absorption in recirculation mode and cannot be washed. They need to be replaced periodically, typically every 3-6 months, depending on usage.

• Remove the aluminum grease filter to access the activated carbon filters.
• Twist or unclip the old activated carbon filters to remove them.
• Install new activated carbon filters, ensuring they are securely attached.
• Re-install the aluminum grease filter.

Replacement activated carbon filters are available under item number 10027530.

Nettoyage général :

• Wipe the exterior surfaces of the hood with a soft cloth dampterminé avec un détergent doux.
• N’utilisez pas de nettoyants abrasifs, de laine d’acier ni de produits chimiques agressifs, car ils peuvent endommager la finition en acier inoxydable.
• Séchez soigneusement toutes les surfaces après le nettoyage.

Figure 6: Cleaning the washable aluminum grease filter.

Dépannage

If you encounter issues with your Klarstein Beretta Island Exhaust Hood, please refer to the following table before contacting customer support.

Spécifications techniques

Garantie et assistance

For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Klarstein products are designed for reliability and performance.

If you require technical assistance, have questions about your product, or need to order replacement parts (e.g., activated carbon filters), please contact Klarstein customer support. You can typically find contact information on the manufacturer's official websur le site ou dans l'emballage d'origine du produit.

Please have your model number (TK15-BerettaKupfer) and purchase details ready when contacting support.