1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your GROHE 29037001 3/4-Inch Bath and Shower Combination. Please read these instructions carefully before beginning installation or use to ensure safe and efficient operation. Keep this manual for future reference.
2. Consignes de sécurité
Consignes de sécurité importantes :
- L'installation doit être effectuée par un professionnel qualifié, conformément aux codes de plomberie et de construction locaux.
- Assurez-vous que l'alimentation en eau principale est coupée avant toute installation ou opération de maintenance.
- Portez un équipement de protection individuelle (EPI) approprié lors de l'installation.
- Do not modify the product. Use only genuine GROHE replacement parts.
- Protéger le produit du gel.
3. Produit terminéview
The GROHE 29037001 is a 3/4-inch bath and shower combination designed for deck mounting. It features a polished brass finish and a single handle for water control. This unit includes an integrated drain system for managing splashing water.
Figure 1 : Main unit of the GROHE 29037001 Bath and Shower Combination, showing the water inlets and outlet connections.
4. Configuration et installation
Outils et matériel requis:
- Clé à molette
- Jeu de tournevis
- Ruban d'étanchéité (ruban PTFE)
- Mètre à ruban
- Percer (si de nouveaux trous sont nécessaires)
4.1 Vérifications avant l'installation
- Vérifiez que tous les composants sont présents et non endommagés.
- Ensure the mounting surface is clean, level, and structurally sound for deck mounting.
- Confirm water supply lines (hot and cold) are accessible and correctly sized (3/4-inch connections).
4.2 Dimensional Information
Figure 2 : Technical drawing with key dimensions for installation. Note the G 1/2 connections and overall unit width of 705mm.
Refer to Figure 2 for precise dimensions and connection points. The unit requires a minimum deck thickness of 28mm (max. 28 shown in diagram) and has G 1/2 connections for water supply.
4.3 étapes d'installation
- Préparez la surface de montage : If installing on a new surface, cut the necessary openings according to the dimensions provided in Figure 2.
- Montez l'unité : Position the main unit into the prepared opening. Secure it to the deck using the provided mounting hardware. Ensure it is stable and level.
- Raccorder l'alimentation en eau : Connect the hot and cold water supply lines to the corresponding inlets on the unit. Use sealant tape on threaded connections to prevent leaks. The connections are 3/4-inch.
- Raccorder le drain : Attach the integrated drain system to the appropriate waste pipe. Ensure all connections are watertight.
- Install Handle and Trim: Attach the single handle and any decorative trim pieces according to the specific instructions provided with those components (if separate).
- Test de fuites : Ouvrez lentement l'arrivée d'eau principale et vérifiez l'étanchéité de tous les raccords. Réparez immédiatement toute fuite.
5. Mode d'emploi
The GROHE 29037001 features a single handle for controlling both water flow and temperature.
- Débit d'eau : Lift the handle to increase water flow. Push down to decrease or stop the flow.
- Contrôle de la température : Rotate the handle left for hot water and right for cold water. Adjust gradually to achieve the desired temperature.
- Shower/Bath Diverter: If a diverter is integrated into the handle or a separate component, operate it to switch between bath spout and showerhead functions.
6. Entretien
Regular maintenance ensures the longevity and optimal performance of your GROHE bath and shower combination.
6.1 Nettoyage
- Clean the polished brass finish with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for brass fixtures.
- Évitez les nettoyants abrasifs, les tampons à récurer ou les produits chimiques agressifs, car ils peuvent endommager la finition.
- Rincez abondamment à l'eau claire et séchez avec un chiffon doux après le nettoyage.
6.2 Entretien des cartouches
If water flow decreases or temperature control becomes inconsistent, the ceramic cartridge may require cleaning or replacement. This procedure should ideally be performed by a qualified plumber.
6.3 Protection antigel
In areas prone to freezing temperatures, ensure the product and associated pipework are adequately protected from frost to prevent damage.
7. Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Faible débit d'eau | Clogged aerator or cartridge; partially closed stopcock; low water pressure. | Clean or replace aerator/cartridge; ensure stopcocks are fully open; check household water pressure. |
| Fuites d'eau au niveau des raccords | Loose connections; worn seals/gaskets; improper sealant application. | Tighten connections; replace seals/gaskets; reapply sealant tape. |
| Température de l'eau irrégulière | Cartouche défectueuse ; problèmes d'alimentation en eau chaude/froide. | Inspect or replace cartridge; check hot/cold water supply lines for blockages or pressure imbalances. |
| Robinet qui goutte | Worn cartridge or seals. | Replace cartridge or seals. |
If troubleshooting steps do not resolve the issue, contact a qualified plumber or GROHE customer support.
8. Spécifications
- Modèle: GROHE 29037001
- Taper: Bath and Shower Combination
- Type de montage : Deck Mount, Widespread
- Matériel: Laiton
- Finition: Brillant
- Couleur: Silver (Silber)
- Nombre de poignées: 1
- Taille de connexion: 3/4-inch (G 1/2 for some internal connections as per diagram)
- Poids de l'article : Environ 7.66 kg (16.85 lb)
- Dimensions du produit : 34.06 x 14.76 x 7.09 pouces (86.5 x 37.5 x 18 cm)
- Composants inclus : GROHE 29037001 Bath and Shower Combination 3/4"
9. Garantie et assistance
Pour obtenir des informations sur la garantie et l'assistance clientèle, veuillez consulter le site officiel de GROHE. website or contact your local GROHE dealer. Keep your proof of purchase for warranty claims.
GROHE Officiel Website: www.grohe.com