Carte d'évaluation DC2383A-B
Guide d'utilisateur
Quad 17V, 1.25A Synchronous Step-DownRegulator with Ultralow Quiescent Current
DESCRIPTION
Demonstration circuit 2383A-B features the LT ® 3644-2: the wide input and output voltagGamme E, haute efficacité et densité de puissance, régulateur monolithique abaisseur synchrone DC/DC à quatre sorties 1.25 A. Le volume d'entréetage range of DC2383A-A is 2.7V to 17V. The default demo board setting of VOUT1, VOUT2, VOUT3, and VOUT4 is 1.2V, 3.3V, 2.5V, and 1.8V at 1.25A maximum DC output current per channel. There are two assembly versions. The DC2383A-B features LTC3644-2 which operates at an internally fixed frequency of 2.25MHz (Typ), while the DC2383A-A features LTC3644 which operates at an internally fixed frequency of 1MHz (Typ). Peak current limit is internally fixed at 2.2A typical per channel. Each channel comes with independent run pin control and power good indicators. Phase shift selection of either 0 degrees or 180 degrees between switch rising edge of channels 1, 2 and channels 3, 4 is also available.
DC2383A-B provides optional onboard 0Ω jumpers to configure the LTC3644-2 as 4-phase dual 2.5A/2.5A outputs or 4-phase triple 2.5A/1.25A/1.25A outputs. Optional 0Ω jumpers connecting VIN1 to VIN2, VIN3, and
VIN4 are available for users to operate selected channels of LTC3644-2 at different input voltages than VIN1.
A user-selectable MODE/SYNC input is provided to allow users to trade off ripple noise for light load efficiency: pulse-skipping mode (PS) or Burst Mode ® operation delivers higher efficiency at light load while forced continuous conduction mode (FCM) is preferred for noise sensitive applications. The MODE/SYNC pin can also be used to synchronize the switching frequency to an external clock or set the phase shift between channels 1, 2, and channels 3, 4. Constant frequency, peak current mode control architecture and integrated internal control loop compensation network, allows very fast transient response to line and load changes while maintaining loop stability.
The LTC3644-2 is available in a thermally enhanced, low-profile 36-lead 5mm x 5mm BGA package. It is recommended to read the LTC3644-2 datasheet and demo board manual prior to using or making any changes to DC2383A-B.
SOMMAIRE DES PERFORMANCES
Specifications are at TA = 25°
PARAMÈTRE | CONDITIONS | MIN | TYP | MAX | UNITÉS |
Vol d'entréetage Gamme VIN | 2.7 | 17 | V | ||
Demo Board Default Output Voltages VOUT1, VOUT2, VOUT3, VOUT4 | FSW = 2.25 MHzBurst Mode VIN = 2.7V to 17V (VOUT < VIN) ILOAD = 0A to 1.25A per Channel |
1.176 3.234 2.45 1.764 | 1.2 3.3 2.5 1.8 |
1.224 366 2.55 1.836 |
V |
Default Switching Frequency | Internally Fixed Switching Frequency | 1.8 | 2.25 | 2.6 | MHz |
Maximum Continuous Output Current IOUT per Channel IOUT1, IOUT2, IOUT3, IOUT4 | FSW = 2.25MHz VIN = 2.7V to 17V (VOUT < VIN) VOUT = 1.2V, 1.8V, 2.5V, 3.3V | 1.25 | A | ||
Efficiency at DC | VIN = 5V FSW = 2.25MHz | 125 | % | ||
VOUT1 = 1.2V at IOUT1 = 1A | 80.6 | ||||
VOUT2 = 3.3V at IOUT2 = 1A | 88.1 | ||||
VOUT3 = 2.5V at IOUT3 = 1A | 86.2 | ||||
VOUT4 = 1.8V at IOUT4 = 1A | 84.7 |
PROCÉDURE DE DÉMARRAGE RAPIDE
The MODE/SYNC pin can be used to synchronize the internal oscillator clock frequency to the external clock signal. Place JP3 (MODE/PLLIN) at the CLKIN position, apply an external clock signal at the CLKIN test point (E10) to vary the switching frequency within ±50% of the internal programmed frequency.
The MODE/SYNC pin can also be used to set the phase shift between channels 1, 2 and channels 3, 4 while keeping the PHASE pin tied to INTVCC. The phase shift can be set by modulating the duty cycle of an external clock on the MODE/SYNC pin. In this case, the phase shift will be determined by the applied external clock rising and falling edges. The switch rising edge of channels 1, 2 is synced to the rising edge of the external clock and the switch rising edge of channels 3, 4 is synced to the falling edge of the external clock. Crosstalk between channels can be avoided by adjusting the phase shift between channels such that the SW edges do not coincide.
(Option) 4-Phase Dual 2.5A/2.5A Output Current Configuration:
DC2383A-B can be configured as dual 2.5A/2.5A outputs.
Channel 1 and channel 4 are master channels, and channel 2 and channel 3 are slaves.
The following simple modification is required:
- Tie VIN1, VIN2, VIN3, and VIN4 together or tie VIN1 and VIN2, VIN3 and VIN4 together if operating channels 1 and channel 2 at different input voltage than that of channel 3 and channel 4. Make sure SVIN is tied to the highest input supply voltage.
- Tie SW1 and SW2, SW3 and SW4 together. Since SW1 and SW2, SW3 and SW4 are tied together, there is only one inductor needed for each output voltage rail. Calculate and insert the inductors needed for L1 and L4, and remove L2 and L3.
- Tie FB2 and FB3 to INTVCC.
- Float (do not use) PGOOD2 and PGOOD3. Only PGOOD1 and PGOOD4 are active.
- Tie RUN1 and RUN2, RUN3 and RUN4 together. Note: Make sure to float all the unused onboard RUN pin jumpers to avoid accidentally shorting VIN to GND.
- Tie PHASE pin to INTVCC. Refer to the demo board DC2383A-B schematic for more details.
(Option) 4-Phase Triple 2.5A/1.25A/1.25A Output Circuit Configuration:
DC2383A-B can be configured as triple 2.5A/1.25A/1.25A outputs.
Channel 1 is a master channel, channel 2 is a slave. Channel 3 and channel 4 are independent channels.
The following simple modification is required:
- Tie VIN1, VIN2, VIN3, and VIN4 together, or tie VIN1 and VIN2 together, and VIN3 and VIN4 can be at different input voltages than VIN1 and VIN2. Make sure SVIN is tied to the highest input supply voltage.
- Tie SW1 and SW2 together. There is only one inductor needed for this output voltage rail. Calculate and insert the inductor needed for L1 and remove L2.
- Tie FB2 to INTVCC.
- Float (do not use) PGOOD2. Only PGOOD1, PGOOD3, and PGOOD4 are active.
- Tie RUN1 and RUN2 together. Note: Make sure to float all unused onboard RUN pin jumpers to avoid accidentally shorting VING to GND.
- Tie PHASE pin to INTVCC.
- Channel 3 and Channel 4 are left unchanged since these two channels operate as independent channels.
Refer to the demo board DC2383A-B schematic for more details.
PROCÉDURE DE DÉMARRAGE RAPIDE
![]() |
![]() |
PROCÉDURE DE DÉMARRAGE RAPIDE
Figure 3. Measured Efficiency at VIN = 5V, FSW = 2.25MHz, Burst Mode
VOUT1 = 1.2V, VOUT2 = 3.3V, VOUT3 = 2.5V, VOUT4 = 1.8V
ILOAD = 1.25A per Channel
TA = 25°C, No Heat Sink, No Forced Airflow
Figure 4. Thermal Performance at VIN = 5V, fSW = 2.25MHz
![]() |
|
(a) Load Transient Response: VIN = 8V, VOUT = 1.2V | (b) Load Transient Response: VIN = 12V, VOUT = 1.8V |
![]() |
|
(c) Load Transient Response: VIN = 12V, VOUT = 2.5V | (d) Load Transient Response: VIN = 12V, VOUT = 3.3V |
Figure 5. Load Transient Responses
Load Transient Response Test Conditions:
FSW = 2.25MHz Typical
VOUT1 = 1.2V, VOUT2 = 3.3V, VOUT3 = 2.5V, VOUT4 = 1.8V
L1 = L4 = 1µH
L2 = L3 = 2.2µH
Load Step = 0.625A to 1.25A at di/dt = 1A/µs
COUT_ceramic = 1×47µF/1206 + 1x10uF/1206 (per Channel)
Feedforward Capacitor: CFF = 68pF (per Channel)
LISTE DES PIECES
ARTICLE | QTÉ | RÉFÉRENCE | DESCRIPTION DES PIÈCES | RÉFÉRENCE FABRICANT |
Composants de circuit requis
1 | 4 | CFF1, CFF2, CFF3, CFF4 | CAP, 0402 68pF 5% 50V C0G | MURATA, GRM1555C1H680JA01D |
2 | 1 | C1 | CAP. 2917 22uF 20% 35V TANT | AVX, TPSE226M035R0125 |
3 | 7 | C2, C4, C5, C7, C9, C10, C14 | CAP, 0805 10uF 10% 25V X5R | MURATA, GRM21BR61E106KA73L |
4 | 5 | C3, C6, C11, C12, C15 | CAP, 0603 4.7uF 20% 25V X5R | MURATA, GRM188R61E475ME11D |
5 | 1 | C16 | CAP, 0603 1uF 10% 25V X7R | MURATA, GRM188R71E105KA12D |
6 | 4 | C19, C21, C23, C25 | CAP, 1206 47uF 10% 16V X5R | MURATA, GRM31CR61C476ME44L |
7 | 4 | C20, C22, C24, C26 | CAP, 1206 10uF 10% 25V X7R | KEMET, C1206C106K3RACTU |
8 | 2 | L1, L4 | IND, 1uH | MURATA, DFE252012F-1R0M |
9 | 2 | L2, L3 | IND, 2.2uH | MURATA, DFE252012F-2R2M |
10 | 5 | RSET1, RSET2, RSET3, RSET4, R25 | RES, 0402 100K OHM 1% 1/16W | PANASONIC, ERJ2RKF1003X |
11 | 9 | R1, R2, R9, R13, R14, R17, R18, R23, R24 | RES, 0402 0 OHM JUMPER | VISHAY, CRCW04020000Z0ED |
12 | 4 | R3, R4, R5, R6 | RES, 0402 100k OHMS 1% 1/16W | VISHAY, CRCW0402100KFKED |
13 | 1 | R7 | RES, 0402 2.2 OHMS 1% 1/16W | VISHAY, CRCW04022R20FNED |
14 | 6 | R8, R10, R11, R12, R15, R16 | RES, 0402 10M OHMS 1% 1/16W | VISHAY, CRCW040210M0FKED |
15 | 1 | R19 | RES, 0402 22.1K OHMS 1% 1/16W | VISHAY, CRCW040222K1FKED |
16 | 1 | R22 | RES, 0402 31.6K OHM 1% 1/16W | VISHAY, CRCW040231K6FKED |
17 | 1 | R28 | RES, 0402 49.9K OHMS 1% 1/16W | VISHAY, CRCW040249K9FKED |
18 | 3 | R29, R30, R31 | RES, 0805 0 OHM JUMPER | VISHAY, CRCW08050000Z0EA |
19 | 1 | U1 | IC, QUAD 17V, 1.25A SYNCHRONOUS STEP-DOWN REGULATOR | ANALOG DEVICES, LTC3644EY-2 |
Composants supplémentaires du circuit de la carte de démonstration
1 | 0 | C8, C13, C17, C18 | CAP, 0402 OPTION | OPTION |
2 | 0 | C27, C28, C29, C30 | CAP, 1206 OPTION | OPTION |
3 | 0 | R20, R21, R26, R27 | RES, 0402 OPTION | OPTION |
4 | 0 | R32 | RES, 1206 OPTION | OPTION |
5 | 0 | R33, R34, R37, R38, R39 | RES, 0603 OPTION | OPTION |
6 | 0 | R35, R36 | RES, 0805 OPTION | OPTION |
Matériel : pour la carte de démonstration uniquement
1 | 16 | E1, E2, E3, E4, E5, E6, E7, E12, E14, E15, E16, E17, E18, E19, E20, E21 | TOURELLE | MILL-MAX, 2501-2-00-80-00-00-07-0 |
2 | 10 | E8, E9, E10, E11, E13, E22, E23, E24, E25, E26 | TOURELLE | MILL-MAX, 2308-2-00-80-00-00-07-0 |
3 | 5 | JP1, JP2, JP4, JP5, JP6 | HEADER, 3PIN, 2mm | WURTH, ELEKTRONIK, 62000311121 |
4 | 1 | JP3 | HEADER, 2X4PINS 2mm | WURTH, ELEKTRONIK, 62000821121 |
5 | 4 | JP7, JP8, JP9, JP10 | HEADER, 2PIN, DBL ROW 2mm | WURTH, ELEKTRONIK, 62000421121 |
6 | 4 | MH1, MH2, MH3, MH4 | STANDOFF, SNAP ON 12.7mm | WURTH, ELEKTRONIK, 702935000 |
7 | 10 | XJP1, XJP2, XJP3, XJP4, XJP5, XJP6, XJP7, XJP8, XJP9, XJP10 | SHUNT, 2mm | WURTH, ELEKTRONIK, 60800213421 |
DIAGRAMME SCHÉMATIQUE
DIAGRAMME SCHÉMATIQUE
OPTIONAL JUMPERS FOR PARALLELING PHASES FOR DESIRED NUMBER OF OUTPUT VOLTAGE RAILS (SHARING THE SAME VIN1)
NUMBER OF OUTPUT VOLTAGE RAILS | Paralleling Channel | Master Channel | 0 OHM (Required) | OPT (Do not stuff) | PHASE (JP13) |
QUAD 1.25A 4 | 1 / 2 / 3 / 4 | R33, R34, R35, R36, R37, R38, R39 | INTVCC | ||
TRIPLE 2.5A/1.25A/1.25A 3 | 1+2/3/4 | 1 | R33, R35, R37 | R4, R9, R10, R17, RSET2, CFF2, R19, R34, R36, R38, R39, L2, JP2 | INTVCC |
DUAL 2.5A/2.5A 2 | 1 + 2/3 + 4 | 1, 4 | R33, R34, R35, R36, R37, R38 | R4, R5, R9, R10, R13, R15, R17, R18, RSET2, RSET3, CFF2, CFF3, R19, R22, R39 L2, L3, JP2, JP5 | INTVCC |
REMARQUE:
Please refer to the datasheet and demo board manual for more details and examples of paralleling phases to obtain the desired number of output voltage rails.
AVIS CLIENT
ANALOG DEVISES INC. HAS MADE THE BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER’S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT NALOG DEVICES INC. APPLICATIONS ENGINEERING FOR ASSISTANCE.
THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES INC. AND SUPPLIED FOR USE WITH ANALOG DEVICES INC. PARTS.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements f patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any atent or patent rights of Analog Devices.
Mise en garde contre les décharges électrostatiques
Dispositif sensible aux décharges électrostatiques (ESD). Les appareils chargés et les circuits imprimés peuvent se décharger sans être détectés. Bien que ce produit comporte des circuits de protection brevetés ou exclusifs, des dommages peuvent survenir sur les appareils soumis à des décharges électrostatiques à haute énergie. Par conséquent, des précautions ESD appropriées doivent être prises pour éviter une dégradation des performances ou une perte de fonctionnalité.
Mentions légales
En utilisant la carte d'évaluation décrite dans le présent document (ainsi que tout outil, documentation sur les composants ou matériel de support, la « carte d'évaluation »), vous acceptez d'être lié par les termes et conditions énoncés ci-dessous (« Contrat »), sauf si vous avez acheté le Carte d'évaluation, auquel cas les conditions générales de vente d'Analog Devices prévaudront. N'utilisez pas le tableau d'évaluation avant d'avoir lu et accepté l'accord. Votre utilisation du comité d'évaluation signifie votre acceptation de l'accord. Le présent accord est conclu par et entre vous (« client ») et Analog Devices, Inc. (« ADI »), avec son siège social à One Technology Way, Norwood, MA 02062, États-Unis. Sous réserve des termes et conditions de l'Accord, ADI accorde par la présente au Client une licence gratuite, limitée, personnelle, temporaire, non exclusive, non sous-licenciable et non transférable pour utiliser la carte d'évaluation UNIQUEMENT À DES FINS D'ÉVALUATION. Le client comprend et accepte que la carte d'évaluation est fournie aux fins uniques et exclusives référencées ci-dessus, et accepte de ne pas utiliser la carte d'évaluation à d'autres fins. En outre, la licence accordée est expressément soumise aux limitations supplémentaires suivantes : le client ne doit pas (i) louer, donner à bail, afficher, vendre, transférer, céder, concéder en sous-licence ou distribuer la carte d'évaluation ; et (ii) permettre à toute tierce partie d'accéder au comité d'évaluation. Tel qu'il est utilisé dans les présentes, le terme « Tiers » inclut toute entité autre que ADI, le Client, leurs employés, leurs sociétés affiliées et leurs consultants internes. La carte d'évaluation n'est PAS vendue au client ; tous les droits non expressément accordés dans les présentes, y compris la propriété du comité d'évaluation, sont réservés par ADI. CONFIDENTIALITÉ. Le présent accord et le comité d'évaluation seront tous considérés comme des informations confidentielles et exclusives d'ADI. Le client ne peut divulguer ou transférer aucune partie du comité d'évaluation à une autre partie pour quelque raison que ce soit. En cas d'arrêt de l'utilisation de la carte d'évaluation ou de résiliation du présent contrat, le client s'engage à renvoyer rapidement la carte d'évaluation à ADI. RESTRICTIONS SUPPLÉMENTAIRES. Les clients ne peuvent pas désassembler, décompiler ou désosser les puces sur la carte d'évaluation. Le client doit informer ADI de tout dommage survenu ou de toute modification ou altération qu'il apporte à la carte d'évaluation, y compris, mais sans s'y limiter, la soudure ou toute autre activité qui affecte le contenu matériel de la carte d'évaluation. Les modifications apportées à la carte d'évaluation doivent être conformes à la loi applicable, y compris, mais sans s'y limiter, la directive RoHS. RÉSILIATION. ADI peut résilier le présent Contrat à tout moment moyennant notification écrite au Client. Le client s'engage à remettre à ADI la commission d'évaluation à ce moment-là. LIMITATION DE RESPONSABILITÉ. LE CONSEIL D'ÉVALUATION FOURNI CI-DESSOUS EST FOURNI « EN L'ÉTAT » ET ADI NE FAIT AUCUNE GARANTIE OU REPRÉSENTATION D'AUCUNE SORTE À L'ÉGARD DE LUI. ADI DÉCLINE SPÉCIFIQUEMENT TOUTE DÉCLARATION, APPROBATION, GARANTIE OU GARANTIE, EXPRESSE OU IMPLICITE, RELATIVE AU COMITÉ D'ÉVALUATION, Y COMPRIS, MAIS SANS S'Y LIMITER, LA GARANTIE IMPLICITE DE QUALITÉ MARCHANDE, DE TITRE, D'ADÉQUATION À UN USAGE PARTICULIER OU DE NON-VIOLATION DES DROITS DE PROPRIÉTÉ INTELLECTUELLE. . EN AUCUN CAS ADI ET SES CONCÉDANTS DE LICENCE NE SERONT RESPONSABLES DES DOMMAGES ACCESSOIRES, SPÉCIAUX, INDIRECTS OU CONSÉCUTIFS RÉSULTANT DE LA POSSESSION OU DE L'UTILISATION PAR LE CLIENT DE LA COMMISSION D'ÉVALUATION, Y COMPRIS, MAIS SANS S'Y LIMITER, LA PERTE DE PROFITS, LES FRAIS DE RETARD, LES FRAIS DE MAIN-D'ŒUVRE OU LA PERTE DE BONNE VOLONTÉ . LA RESPONSABILITÉ TOTALE D'ADI POUR TOUTE CAUSE SERA LIMITÉE À UN MONTANT DE CENT DOLLARS US (100.00 $). EXPORTATION. Le client s'engage à ne pas exporter directement ou indirectement la carte d'évaluation vers un autre pays et à se conformer à toutes les lois et réglementations fédérales américaines applicables en matière d'exportation. DROIT APPLICABLE. Le présent Accord sera régi et interprété conformément aux lois de fond du Commonwealth du Massachusetts (à l'exclusion des règles de conflit de lois). Toute action en justice concernant cet accord sera entendue par les tribunaux d'État ou fédéraux ayant juridiction dans le comté de Suffolk, Massachusetts, et le client se soumet par la présente à la juridiction personnelle et au lieu de ces tribunaux.
01/22
www.analog.com
© ANALOG DEVICES, INC. 2022
Documents / Ressources
![]() |
ANALOG DEVICES DC2383A-B Evaluation Board [pdf] Mode d'emploi DC2383A-B, Evaluation Board, DC2383A-B Evaluation Board, Board, Motherboard |