FOURAIR MWIRR-A1 Wireless IR Repeater
Product Information
Specifications
- Compliance: Part 15 of the FCC Rules
- Conditions: Must not cause harmful interference, must accept any received interference
- RF Exposure: Meets general RF exposure requirements
- Usage: Portable exposure without restriction
Product Usage Instructions
Compliances and Conditions
Ensure that the device is operated in compliance with Part 15 of the FCC Rules. The device should not cause harmful interference and must accept any interference it receives.
RF Exposure
The device has been evaluated to meet general RF exposure requirements. It can be used in portable exposure conditions without any restrictions. However, it is recommended to maintain a safe distance from the device during operation to minimize exposure.
Modifications
Warning: Any changes or modifications not expressly approved by the responsible party for compliance could void the user’s authority to operate the equipment. Avoid making any unauthorized modifications to the device.
PACKAGE CONTENTS
- l X IR Receiver Unit
- l X IR Emitter Unit
- l X IR Receiver Extension Cable
- l X IR Emitter Extension Cable
- 2 X Power Adapters
- 2 X USB Power Cables
- l X User Manual
- 2 X 3M Adhesive
| Input Voltage | SV DC |
| Receiver Standby Power | <0.2W |
| Emitter Standby Power | <0.2W |
| IR Frequency | 20-60KHz |
| RF Frequency | 433MHz |
PRODUCT OVERVIEW
OPERATING INSTRUCTIONS
Typical Installation
Step One: Plug the power adapter and connect it to the Infrared Receiver and the Infrared emitter via the USB power cables, the LED indicator of the receiver and the emitter will blink twice.
Step Two: Put the infrared receiver line-in-sight of the IR remote controller, and ensure that the IR remote controller has a clear line of sight to the IR receiver bud, if the receiver receives an available signal, the LED indicator of the infrared receiver will blink.
Step Three: Put the infrared emitter line-in-sight of the device that needs to be controlled, ensure that the infrared emitter bud has a clear line of sight to the IR “eye” of your device, if the emitter transmits has an available signal, the LED indicator of the infrared emitter will blink.
Note: it is easy to mistake the IR cable on the front for the port. please ensure that the power adapter is plugged into the appropriate port at the back and in place.
Optional The IR Receiver and The Emitter Extension Cable
Step One: If you want to extend the reach or hide the IR receiver, connect the IR Receiver Extension Cable to the device.
Step Two: If you want to extend the reach or hide the IR Emitter, connect the IR Emitter Extension Cable to the device. The IR emitter cable can attach to the IR”eye”ofthe device you wish to control.
Note: Please keep in mind to place the extension cable’s emitter bud attached to the IR”eye” of the device no further than 2 inches for the best signal.
ADHESIVE PLACEMENT
To keep the IR Infrared receiver and emitter in one place, we have included adhesive.
TROUBLESHOOTING
| The LED indicator of | Maybe you are using | This infrared receiver only |
| the receiver does not | the non-infrared signal | supports the IR remote |
| blink | IRremote controller, | controller which can |
| such as the Bluetooth | receive a infrared | |
| remote controller, the | signal,not suitable for the | |
| RF remote controller, or | non-infrared signal IR | |
| the WiFi remote | remote controller,please | |
| controller. | contact our customer | |
| service for help! | ||
| The IR remote | Please move the IR remote | |
| controller is beyond a | controller close to the | |
| available range to the | infrared receiver. | |
| infrared receiver. | ||
| The IR Remote | Please adjust the | |
| controller is misaligned | installation direction of the | |
| with the infrared | infrared receiver or the | |
| receiver bud | direction of the IRremote | |
| controller to ensure that | ||
| the IR remote controller is | ||
| aligned with the infrared | ||
| receiver bud. | ||
| The LED indicator of | The infrared emitter is | Please shorten the |
| the emitter does not | beyond a available | distance between the |
| blink. | range to the infrared | infrared emitter and the |
| receiver. | infrared receiver. | |
| The infrared emitter is | For example, a metal | |
| placed inside the | cabinet will shield the | |
| object that shields the | wireless signals and | |
| signal. | shorten the distance of | |
| wireless transmission,so | ||
| please try to stay away | ||
| from the metal shields. |
| The controlled device does not working | The infrared emitter is too far away from the receiver bud of the controlled device. | The infrared emitter need to be aligned with the controlled device,and keep in mind they are no further than 16 inches. |
| You are using the extension cable of the emitter, and the emitter is too far away from the receiver bud of the controlled device. | Please keep in mind to place the infrared emitter bud to the controlled device no further than 2 inches. | |
| Other unexpected problem | Unkown reasons | Any issues,just feel free to contact our customer service,your satisfaction is the greatest motivation to us. |
WARRANTY INFORMATION
If you have any product questions, or you have any product issues, please contact our e-mail: supportfourair@l63.com
Your name: ______ Order number: _______
E-mail: _______ Phone: _________
Frequently Asked Questions
Q: Can I modify the device without approval?
A: No, any changes or modifications not approved by the responsible party for compliance may void your authority to operate the equipment.
Q: Is there a restriction on the device’s usage?
A: The device can be used in portable exposure conditions without restriction, following the compliance and conditions outlined in the manual.
Documents / Resources
 | FOURAIR MWIRR-A1 Wireless IR Repeater [pdf] User Manual 2A3V5-MWIRR-A1, 2A3V5MWIRRA1, MWIRR-A1 Wireless IR Repeater, MWIRR-A1, MWIRR-A1 IR Repeater, Wireless IR Repeater, IR Repeater, Wireless Repeater, Repeater |
