Categories: fantech

fantech 401339 FKD Series Inline Centrifugal Fans Instruction Manual

fantech 401339 FKD Series Inline Centrifugal Fans

PARTS IN THE BOX

  • Inline Fan FKD, 1 pc
  • Electrical Box Hardware, 1 pc
  • Operation and Installation Manual, 1 pc

Warning

Before installation, servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

  1. The compactness and adaptability of the FKD Series fans permit easy installation. The fans are shipped fully assembled and can be mounted at any angle. For various mounting, see figures on the following page.
  2. Because this unit has rotating parts, safety precautions should be exercised during all phases of installation, operation and maintenance.
  3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Material and Vapors.”
    For indoor installation only.
  4. Remove unit from package and inspect within 15 days after receipt. If damaged, report damage to carrier. Do Not operate this unit with visible damage to the blower or impeller assembly.
  5. CAUTION: “This unit has an unguarded impeller. Do not use in locations readily accessible to people or animals.”
    WEAR HAND PROTECTION AND STAY CLEAR OF SHARP EDGES!
  6. Screen guards must be installed within reach of personnel, within (7) feet of the working area, or when advisable for safety.
  7. PLEASE read the entire manual before installing

WARNINGS
DO NOT CONNECT POWER SUPPLY until fan is completely installed. Make sure electrical service to the fan is in the locked “OFF” position.

  1. All fans are suitable for use with solid-state speed control. Three phase units must be wired through a motor contactor.
  2. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS -OBSERVE THE FOLLOWING:
    a. Use this unit in the manner intended by the manufacturer. If you have any questions, contact your manufacturer’s representative or contact us directly.
    b. CAUTION: Before installation, servicing or cleaning unit, switch power off at service panel and lock the service disconnection means to prevent power from being switched on accidentally. When the service disconnection means cannot be locked, securely fasten a prominent warning device, such as tag, to the panel.
    c. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
    d. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Association (NFPA), and the American Society for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities.
    e. When cutting or drilling into wall and ceiling, do not damage electrical wiring and other hidden utilities.
    f. Ducted fans must always be vented to the outdoors.
    g. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) -protected branch circuit.
    h. NEVER place a switch where it can be reached from a tub or shower.
  3. WARNING! Check voltage at the fan to see if it corresponds to the motor name plate.

MOUNTING ILLUSTRATION 1

Please follow all applicable codes when installing this unit

  1. Equipment should be hung at its proper elevation by using temporary fixtures that can be removed after vibration hangers are installed. (Vibra-tion isolation mounts provided by others)
  2. Hanger may be fastened directly to the structure or somewhere be-tween suspended unit (be sure not to over tighten the neoprene element).
  3. Install hangers.
  4. Turn nuts on rod assembly clockwise one complete turn on each hanger. Repeat this procedure until temporary hanging fixtures are loose and load of piping or equipment is suspended completely on the vibration hangers.
  5. Remove temporary hanger fixtures and level piping or equipment by taking additional turns on the spring/top hanger rod nut – clockwise to raise, counterclockwise to lower as required.
  6. If equipping fan with isolators (FC Clamps), they should be attached at this time.
  7. See wiring section to complete installation.

MOUNTING ILLUSTRATION 2

Please follow all applicable codes when installing this unit

  1. Install wood supports to structure for fan mounting.
  2. If equipping with vibration mounts, attach to supports.
  3. Attach fan to vibration mounts, supplied by others (be sure not to over tighten the neoprene element).
  4. if equipping fan with isolators (FC Clamps), they should be attached at this time.
  5. See wiring section to complete installation.

MOUNTING ILLUSTRATION 3

Please follow all applicable codes when installing this unit

  1. Create/Install angle wood supports to structure for fan mounting.
  2. If equipping with vibration mounts, attach to supports.
  3. Attach fan to vibration mounts, supplied by others (be sure not to overtighten the neoprene element).
  4. If equipping fan with isolators (FC Clamps), they should be attached at this time.
  5. See wiring section to complete installation.

DIMENSIONS AND WIRING

For installations in which the fan is connected to a range hood, or if an exhaust grill connected to the fan is located above or near the cooking
surface, as shown, be sure to observe the following safety warning:
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
(Use only galvanized steel ductwork)
Use only galvanized steel ductwork in accordance with all applicable codes.
(Note: If the fan is not connected to a range hood, or a grill in the vicinity of the cooking surface, other approved ducting may be used. Check your local codes.)  WARNING 

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

  • Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
  • Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé’).
  • Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
  • Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: 

  • SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
  • NEVER PICK UP A FLAMING PAN – You may be burned
  • DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
  • Use an extinguisher ONLY if:
  1. You know you have a Class ABC extinguisher, and you already know how to operate it.
  2. The fire is small and contained in the area where it started.
  3. The fire department is being called.
  4. You can fight the fire with your back to an exit.

WIRING

120/230 Volt Single Phase Fan
FKD 12XL, FKD 14, FKD 14XL, FKD 16, FKD 16XL and FKD 18

Wiring schematic for 4 lead motors, single phase

  1. All leads are color coded as well as identified with an Alpha/Alpha or Alpha/Numeric code (i.e. TK or Z2). This code may be shown as a band on the wire or on a schematic on the motor hub. Colors should be verified against code band. If code band and color do not correspond to schematics above, wire according to the code on the band.
  2. Color of capacitor leads may be reversed. Fan operation will not be affected.

 208/230 Volt Three Phase Fans

  1. Contactor should be used. Control coil should be wired in series with motor thermal contacts (TK leads) as shown in diagram to provide thermal motor protection.
  2. All leads are color coded as well as identified with a band containing an Alpha/Alpha or Alpha/Numeric code (i.e. TK or Z2). Colors should be verified against code band. If code band and color do not correspond to schematics above, wire according to the code on the band.

 460 Volt Three Phase Fan

For 460 volt operation, Orange (W2), Red (U2) and Grey (V2) wires must be spliced together.

  1. Contactor should be used. Control coil should be wired in series with motor thermal contacts (TK leads) as shown in diagram to provide thermal motor protection.
  2. All leads are color coded as well as identified with a band containing an Alpha/Alpha or Alpha/Numeric code (i.e. TK or Z2). Colors should be verified against code band. If code band and color do not correspond to schematics above, wire according to the code on the band.

WARRANTY

Three (3) Year Warranty

This warranty supersedes all prior warranties

DURING ENTIRE WARRANTY PERIOD:
Fantech will repair or replace any part which has a factory defect in workmanship or material. Product may need to be returned to the Fantech factory, together with a copy of the bill of sale and identified with RMA number.
FOR FACTORY RETURN YOU MUST:

  • Have a Return Materials Authorization (RMA) number. This may be obtained by calling Fantech either in the USA at 1.800.747.1762 or in CANADA at 1.800.565.3548. Please have bill of sale available.
  • The RMA number must be clearly written on the outside of the carton, or the carton will be refused.
  • All parts and/or product will be repaired/replaced and shipped back to buyer; no credit will be issued.

OR
The Distributor may place an order for the warranty part and/or product and is invoiced. The Distributor will receive a credit equal to the invoice only after product is returned prepaid and verified to be defective.
FANTECH WARRANTY TERMS DO NOT PROVIDE FOR REPLACEMENT WITHOUT CHARGE PRIOR TO INSPECTION FOR A DEFECT. REPLACEMENTS ISSUED IN ADVANCE OF DEFECT INSPECTION ARE INVOICED, AND CREDIT IS PENDING INSPECTION OF RETURNED MATERIAL. DEFECTIVE MATERIAL RETURNED BY END USERS SHOULD NOT BE REPLACED BY THE DISTRIBUTOR WITHOUT CHARGE TO THE END USER, AS CREDIT TO DISTRIBUTOR’S ACCOUNT WILL BE PENDING INSPECTION AND VERIFICATION OF ACTUAL DEFECT BY FANTECH.
THE FOLLOWING WARRANTIES DO NOT APPLY: 

  • Damages from shipping, either concealed or visible. Claim must be filed with freight company.
  • Damages resulting from improper wiring or installation.
  • Damages or failure caused by acts of God, or resulting from improper consumer procedures, such as:
    1. Improper maintenance
    2. Misuse, abuse, abnormal use, or accident, and
    3. Incorrect electrical voltage or current.
  • Removal or any alteration made on the Fantech label control number or date of manufacture.
  • Any other warranty, expressed, implied or written, and to any consequential or incidental damages, loss or property, revenues, or profit, or costs of removal, installation or reinstallation, for any breach of warranty.

WARRANTY VALIDATION 

  • The user must keep a copy of the bill of sale to verify purchase date.
  • These warranties give you specific legal rights, and are subject to an applicable consumer protection legislation. You may have additional rights which vary from state to state.

Limitation of Warranty and Liability

This warranty does not apply to any Fantech product or part which has failed as a result of faulty installation or abuse, incorrect electrical connections or alterations made by others, or use under abnormal operating conditions or misapplication of the product or parts. We will not approve for payment any repair not made by us or our authorized agent without prior written consent. The foregoing shall constitute our sole and exclusive warranty and our sole exclusive liability, and is in lieu of any other warranties, whether written, oral, implied or statutory. There are no warranties which extend beyond the description on the page hereof. In no event, whether as a result of breach of contract, or warranty or alleged negligence, defect incorrect advice or other causes, shall Fantech be liable for special or consequential damages, including, but not limited to, loss of profits or revenue, loss of use of equipment or any other associated equipment, cost of capital, cost of substitute equipment, facilities or services, downtime costs, or claims of customers of purchase for such damages. Fantech neither assumes or authorizes any person to assume for it any other liability in connection with the sale of product(s) or part(s). Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you.

Warning 

Fantech products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100% free from defects. Even reliable products will experience occasional failures and this possibility should be recognized by the user. If these products are used in a life support ventilation system where failure could result in loss or injury, the user should provide adequate backup ventilation, supplementary natural ventilation, failure alarm system, or acknowledge willingness to accept the risk of such loss or injury.

registration.fantech.app

  • United States Tel.: 800 747 1762
  • Canada Tel.: 800 565 3548
  • Latinoamérica Tel.: +52 55 1328 7328

Documents / Resources

fantech 401339 FKD Series Inline Centrifugal Fans [pdf] Instruction Manual
401339, FKD Series Inline Centrifugal Fans, Inline Centrifugal Fans, Centrifugal Fans, 401339, Fans

References

Recent Posts

TCL ALT408DL Flip 2 4GB Flip Phone User Guide

ALT408DL Flip 2 4GB Flip Phone Quick Start Guide At a glance Let's get started.…

3 mins ago

DAYTONA 64051 2-Ton Floor Jack Cross Beam Owner’s Manual

64051 2-Ton Floor Jack Cross Beam Owner's Manual & Safety Instructions Save This Manual Keep…

3 mins ago

IKEA 802.565.01 DUKTIG Toy Cash Register Instruction Manual

802.565.01 DUKTIG Toy Cash Register DUKTIG English 4 Español 5 Portugues 6 8 12 16…

14 mins ago

MACHEREY-NAGEL 985-669 NanoColor Nitrite 4 Tube Test Instruction Manual

985-669 NanoColor Nitrite 4 Tube Test REF 985 669 Test 6-69 Robot 06.16 Nitrite 4…

19 mins ago

SALAMANDER 537SLPM2B Synergy Triple Panel Mount Instruction Manual

537SLPM2B Synergy Triple Panel Mount SYNERGY TRIPLE PANEL MOUNT SL /PM2 BEFORE YOU BEGIN ·…

27 mins ago

PHILIPS OLED936 Series Smart TV User Guide

OLED936 Series Smart TV Television Quick Start Guide OLED936 series AA B 2 A 1…

27 mins ago