iPRO LOGOجعبه آداپتور
کتابچه راهنمای دستور العمل
iPRO WVQJB500 W Adapter Boxشماره مدل
WV-QJB500-W
WV-QJB500-S
WV-QJB500-G

هشدارها

  • از این براکت استفاده نکنید مگر در دوربین های مناسب.
    عدم رعایت این مسئله ممکن است باعث افت و در نتیجه جراحت یا تصادف شود.
  • کار نصب را به فروشنده ارجاع دهید.
    Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
    حتماً با فروشنده مشورت کنید.
  • Install the product securely on a wall or a ceiling in accordance with the installation instructions.
    عدم رعایت این مورد ممکن است باعث صدمه یا تصادف شود.
  • لبه های قطعات فلزی را با دست نکشید.
    رعایت نکردن این امر ممکن است باعث آسیب شود.

هنگام استفاده از این محصول ، "موارد احتیاطی" را که در دستورالعمل عملکرد دوربین متصل شده است نیز بخوانید. 

مقدمه
Use this product when performing outdoor wiring of a box-type camera for outdoor or a wall mount bracket such as using a conduit.
For the latest information about the supported cameras, refer to our support webسایت
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information<ControlNo.:C0501,C0502>).

مشخصات

دمای کار محیط: -50 ° C تا +60 ° C (-58 ° F تا +140 ° F)
ابعاد: 115 میلی متر (W) x 115 میلی متر (H) x 40 میلی متر (D)
(4-17/32 inches (W) x 4-17/32 inches (H) x 1-11/16 inches (D))
جرم: Approx. 430 g (0.95 Ibs)
پایان: Base bracket: Aluminum die cast
Attachment plate: Stainless
WV-QJB500-W: i-PRO white
WV-QJB500-S: Silver
VW-QJB500-G: Light gray

* This product consists of an attachment plate and a base bracket and they are separately packaged.

اقدامات احتیاطی برای نصب

  • In order to prevent injury, the product must be securely mounted to a ceiling or wall according to the Installation Guide of this bracket.
  • اطمینان حاصل کنید که اگر این محصول دیگر مورد استفاده قرار نمی گیرد ، آن را حذف کنید.

لوازم جانبی استاندارد

Operating Instructions (this document) …….. 1 pc.
Installed auxiliary wire* ………………………….. 1 pc.
Hexagon screw …………………………………. 5 pcs.
(M4 × 14 mm {9/16 inches}) (of them, 1 for spare)
Fixing screws for attachment plate ………… 5 pcs.
(M4 × 10 mm {13/32 inches}) (of them, 1 for spare)
Screw for temporary fixing …………………… 2 pcs.
(M3 × 3.5 mm {1/8 inches}) (of them, 1 for spare)

* An installed auxiliary wire is equipped with the attachment plate. 

سایر موارد مورد نیاز (شامل نمی شود)
Fixing screws (M4) …………………. 4 pcs.
مهم

  • Minimum pullout strength: 196 N {44 lbf} (per 1 pcs.)
  • این مقدار نشان دهنده حداقل مقدار استحکام کشش در هر پیچ است. برای اطلاعات در مورد حداقل قدرت کشش، به پشتیبانی ما مراجعه کنید webسایت (https://i-pro.com/global/en/surveillance/training_support/support/technical_information<ControlNo.:C0120>).
  • Select screws according to the material of the location where the camera will be mounted. In this case, wood screws and nails should not be used.

آماده سازی

Remove the tape fixing installed auxiliary wire (accessory) on the attachment plate.
When installing another bracket on this product
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an exampلو

  1. Remove the installed auxiliary wire (accessory) from the attachment plate. iPRO WVQJB500 W Adapter Box - FIG 1
  2. Attach the screw for temporary fixing (accessory) to the bracket to be installed on this product.iPRO WVQJB500 W Adapter Box - FIG 2 Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
  3. If necessary, install the attachment plate provided with the camera to WV-QWL500-W by following the instructions described in the Operating Instructions of WV-QWL500-W.

When using a conduit

  • Remove the cap for the female or thread for the conduit using a 5 mm hex wrench and attach the conduit.
    The female thread for the conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

iPRO WVQJB500 W Adapter Box - FIG 3

نصب و راه اندازی

Step 1: Process the installation surface.
(Screw holes (4 places)/ Cable access hole (1 place))
When directly installing this product, process the installation surface.
توجه داشته باشید:

  • Determine the fixing screw hole diameter and depth in accordance with the specifications of the screws or anchors (x4) (M4: locally procured).
  • When wiring using a conduit, it is unnecessary to process the cable access hole on the installation surface. Make a fixing screw hole so that the cable access hole (for conduit) of the base bracket is arranged in the direction of the conduit.

Depending on the condition of the ceiling or the wall surface, the following five patterns of screw positions are available for fixation of the base bracket. Use only the holes of the same pattern (A – E) for mounting.

iPRO WVQJB500 W Adapter Box - FIG 4

عمودی افقی
A 83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches}) 46 mm {1-13/16 inches} (47.6 mm {1-7/8 inches})
B 46 mm {1-13/16 inches} (47.6 mm {1-7/8 inches}) 83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches})
C* 83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches}) -
D* - 83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches})
E 63 mm (2-15/32 inches} 63 mm (2-15/32 inches}

* When mounting to a single-gang junction box, fix with two fixing screws (M4: locally procured) using the holes of either pattern C or D.

مرحله 2: Fix the base bracket on the installation surface or on a junction box.
Pass the cables through the base bracket and then fix the base bracket on the installation surface or on a junction box (locally procured) with fixing screws (M4: locally procured).
When installing the base bracket on the installation surface
توجه داشته باشید:

  • When installing this product outdoors, be sure to apply waterproofing to the cable access hole and the holes for fixing the screw.

iPRO WVQJB500 W Adapter Box - FIG 5The illustration shown on the left is an example when installing on a wall using the combination of the fixing screw holes that is 83.5mm {3-9/32inches} × 46mm {1-13/16inches}.

■ When mounting the base bracket to a junction box
Select the holes on the base bracket so that they match with the screw holes of the junction box.
توجه داشته باشید:

  • When using a two-gang junction box, it is recommended that the boxes are arranged side by side as shown in the illustration below. (The cable connection work on the empty box side will become easier.)

iPRO WVQJB500 W Adapter Box - FIG 6

Step 3: Fix the attachment plate.
Fix the attachment plate with four fixing screws for the attachment plate (M4: accessory).
Recommended tightening torque: 1.37 N·m {1.01 lbf ft}

iPRO WVQJB500 W Adapter Box - FIG 7

توجه داشته باشید:

  • When wiring using a conduit, complete the connection work on the base bracket side before fixing the attachment plate.
  • When installing this product on a wall, fix the attachment plate with the “TOP⇧” mark facing upward.
  • When installing this product on a ceiling, fix the attachment plate so that the “TOP⇧” mark is faced in the direction where the camera is aiming at.

مرحله 4: Install a camera or other bracket on this product.
■ When installing a camera
The following are descriptions of how to install WV-U1542L (outdoor box type) on a wall using this product as an example. The installation procedure is the same for other cameras.

  1. Hang the camera by hooking the installed auxiliary wire on this product on the hook on the rear of the camera mount base as shown in the illustration on the right.
  2. Connect the cables by following the instructions in the Installation Guide of the camera.
  3. Temporarily fix the camera mount base by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 8iPRO WVQJB500 W Adapter Box - FIG 9
  4. Fix the camera on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}
    iPRO WVQJB500 W Adapter Box - FIG 10

■ When mounting another bracket
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an exampلو

  1. Pass the cable through WV-QWL500-W and temporarily fix it by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 11
  2. Fix WV-QWL500-W on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}iPRO WVQJB500 W Adapter Box - FIG 12
  3. Install the camera by following the Operating Instructions of WV-QWL500-W.
  • قبل از اقدام به اتصال یا نصب این محصول ، لطفاً این دستورالعمل ها را با دقت بخوانید و این کتابچه راهنما را برای استفاده در آینده ذخیره کنید.
  • ظاهر خارجی و سایر قسمت های نشان داده شده در این کتابچه راهنما ممکن است با محصول واقعی در محدوده متفاوت باشد که به دلیل بهبود محصول ، در استفاده عادی اختلال ایجاد نمی کند.

i-PRO Co., Ltd. هیچ مسئولیتی در قبال صدمات یا خسارات مالی ناشی از خرابی های ناشی از نصب یا عملیات نادرست مغایر با این مستندات ندارد.

تـذکــــر: توجه:
• Before attempting to connect or operate this product, please read these instructions carefully. • This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily
reach it.
• For information about screws and brackets required for installation, refer to the corresponding section of this document.

برای ایالات متحده و کانادا:
i-PRO Americas Inc.
برای اروپا و سایر کشورها:
i-PRO EMEA B.V.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
iPRO WVQJB500 W Adapter Box - BAR CodeNs0520-1042
چاپ شده در چین

اسناد / منابع

i-PRO WV-QJB500-W Adapter Box [pdf] راهنمای دستورالعمل
WV-QJB500-W, Adapter Box, WV-QJB500-W Adapter Box, Box

منابع

پیام بگذارید

آدرس ایمیل شما منتشر نخواهد شد.