Topyond Ebike LCD Display User Manual

1. مقدمه

The Topyond Ebike LCD Display is designed to provide essential real-time information for your electric bike or scooter. This display meter allows you to monitor speed, distance traveled, battery level, and other critical performance metrics, enabling informed decisions during your ride. Crafted from high-quality ABS material, it ensures durability and resistance to wear and tear. Its compact design with a 22.5mm diameter ensures broad compatibility and ease of installation across various electric scooter and bike models.

2. اطلاعات ایمنی

• قبل از سوار شدن، همیشه مطمئن شوید که صفحه نمایش به طور ایمن نصب شده است.
• Do not attempt to disassemble or modify the display, as this may void the warranty and cause damage.
• Keep the display clean and free from excessive moisture. While waterproof, prolonged submersion is not recommended.
• Avoid extreme temperatures, both hot and cold, to ensure optimal performance and longevity.
• If any unusual behavior or error codes appear, refer to the troubleshooting section or contact support.

3. محتویات بسته

لطفاً بررسی کنید که همه اقلام در بسته شما موجود باشد:

• 1 x Topyond Electric Bike LCD Display Meter
• 1 x دفترچه راهنمای کاربر

4. محصول تمام شدview

The Topyond Ebike LCD Display features a clear screen and intuitive button layout for easy operation. Below are images illustrating the display from various angles, highlighting its design and key features.

5. راه اندازی و نصب

The Topyond Ebike LCD Display is designed for easy installation on handlebars with a 22.5mm diameter. Follow these steps to properly install your display:

1. انتخاب مکان: Select a suitable position on your ebike's handlebar, typically near the grip, ensuring it does not obstruct braking or shifting.
2. نصب نمایشگر: Loosen the screw on the display's mounting bracket. Place the display on the handlebar and tighten the screw until it is secure. Ensure the display is oriented correctly for optimal viewing.
3. کابل های اتصال: Connect the display's cable to the corresponding connector on your ebike's controller or wiring harness. Ensure the 5-pin connector is firmly seated. The line sequence of the label connector is typically: Red (VCC), Black (GND), Blue (TX), Green (RX), Yellow (DS).
4. عملکرد تست: After installation, turn on your ebike to verify the display powers on and shows information correctly.

6. دستورالعمل های عملیاتی

The Topyond Ebike LCD Display provides various functions and settings to enhance your riding experience. Familiarize yourself with the buttons and display information.

6.1. توابع دکمه

• Power Button (Middle): Press and hold to turn the display ON/OFF. Short press to switch between ODO (Odometer), TRIP (Trip Distance), VOL (Voltage), and TIME.
• '+' Button (Top): Short press to increase parameter values or navigate menus.
• '-' Button (Bottom): Short press to decrease parameter values or navigate menus.
• وارد کردن تنظیمات: To enter the settings menu, press and hold the '+' and '-' buttons simultaneously.

6.2. Display Functions (LCD-930 Hand Control Panel)

The display provides comprehensive information at a glance:

• نمایش سرعت: Shows current speed (AVG: average speed, MAX: maximum speed).
• نشانگر قدرت: Battery level display.
• نشانگر خطا: Displays error codes if issues occur.
• Total Mileage (ODO): Cumulative distance traveled.
• مسافت پیموده شده تکی (TRIP): Distance for the current ride.
• Single Boot Time (TIME): مدت زمان سفر فعلی.
• باتری جلدtage (VOL): حجم باتری فعلیtage.
• DST: فاصله.
• استقامت: Estimated remaining range.

6.3. Settings and Parameters (P09-P15 Menu)

To access and modify advanced settings, enter the P09-P15 menu by holding the '+' and '-' buttons. Use '+' and '-' to navigate and change values, and the Power button to confirm or exit.

• P01: Backlight Brightness: Adjusts display backlight (Level 1-3).
• P02: Mileage Unit: 0 for KM, 1 for MILE.
• P03: جلدtagسطح e: ولوم باتری را تنظیم می کندtage (24V, 36V, 48V, 60V). Default is 36V.
• P04: Dormancy Time: Sets the time until the display enters sleep mode (0: no dormancy, 1-60 minutes).
• P05: کمک کنید File: 0، 3 file حالت
• P06: Wheel Diameter: Sets the wheel diameter in inches for accurate speed and distance readings.
• P07: Speed Gauge Magnetic Steel Number: Sets the number of magnetic steel poles for the speed sensor.
• P08: Speed Limit: Sets the maximum speed (0-100km/h).
• P09: Zero Start/Non-Zero Start: 0 for zero start, 1 for non-zero start.
• P10: Drive Mode: 0 for power drive, 1 for electric drive (throttle), 2 for power drive and electric drive coexistence.
• P11: Help Sensitivity Setting Range: 1-24.
• P12: Help Start Intensity Setting Range: 0-5.
• P13: تنظیم نوع دیسک فولادی مغناطیسی قدرت: 5, 8, 12 Magnetic Steel Types.
• P14: Controller Limit Value Set Default: 12A range: 1-20A.
• P15: Controller Under Voltage.

7. تعمیر و نگهداری

Proper maintenance ensures the longevity and optimal performance of your Topyond Ebike LCD Display.

• تمیز کردن: استفاده از نرم، دamp cloth to wipe the display screen and body. Avoid abrasive cleaners or solvents that could damage the ABS material or screen.
• قرار گرفتن در معرض آب: While the display is waterproof, avoid high-pressure water jets directly on the unit. Dry any moisture promptly after exposure to rain.
• ذخیره سازی: When not in use for extended periods, store the ebike and display in a cool, dry place away from direct sunlight and extreme temperatures.
• بازرسی کابل: Periodically check the connection cables for any signs of wear, fraying, or damage. Ensure connections remain secure.

8 عیب یابی

If you encounter issues with your Topyond Ebike LCD Display, refer to the common problems and their solutions below. The display may show specific error codes to help diagnose the problem.

8.1. Vehicle Status Code Meanings

۷.۳ نکات عیب‌یابی عمومی

• روشن نشدن صفحه نمایش: Ensure the battery is charged and properly connected. Check all cable connections between the display and the ebike's system.
• قرائت های نادرست: Verify that the wheel diameter (P06) and magnetic steel number (P07) settings are correctly configured in the display's parameters.
• دکمه ها پاسخگو نیستند: Check for any physical obstructions or debris around the buttons. If the issue persists, a factory reset (if available) or professional inspection may be needed.

9. مشخصات

Detailed technical specifications for the Topyond Ebike LCD Display:

10. گارانتی و پشتیبانی

Topyond is committed to providing high-quality products. For any questions, technical assistance, or warranty claims, please refer to the contact information provided with your purchase or visit the official Topyond store on Amazon. Please retain your proof of purchase for warranty purposes.