blustream.co.uk
Blustream Home . Blustream
Профессиональная акустика — Активные акустические системы.
User Manual for BLUSTREAM models including: DA44AU 4x4 Dante Digital Audio Converter, DA44AU, 4x4 Dante Digital Audio Converter, Digital Audio Converter, Audio Converter, Converter
Приборы обработки Xilica DA44AU купить в Москве с доставкой
File Info : application/pdf, 12 Pages, 606.05KB
DocumentDocumentDA44AU User Manual https://muzcentre.ru RevA3_User_Manual_DA44AU Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended. This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment. DA44AU USER MANUAL Contents Introduction Features Panel Descriptions Audio Input Settings Dante® Controller Advanced Dante® Settings Product Schematic RS-232 Control Port Specifications Packaging Contents Acknowledgements Installer Notes 03 03 04 05 05 - 06 06 07 08 09 09 09 10 - 11 02 www.blustream.com.au | www.blustream.co.uk DA44AU USER MANUAL Introduction Our DA44AU is a four input / four output Dante® digital audio converter. The DA44AU allows any non-Dante® audio source such as mixing consoles, amplifiers, computers and Blustream Matrix products or distribution products to be connected as an audio source within a Dante® network, as well as converting a Dante® signal back to an analogue audio signal. The DA44AU supports both balanced and unbalanced audio as well as microphone line level inputs inc. 48V phantom power. The DA44AU supports AES67 RTP audio transport. FEATURES: · Features 4x analogue audio inputs that are converted to a Dante® compatible signal · Features conversion of Dante® signal to 4 x analogue audio outputs · Analogue audio inputs support both balanced and unbalanced audio + MIC line level signals · MIC line level supports 48V Phantom power · Supports 44.1, 48 & 96 KHz sample rates @ 24 Bit · Configurable Dante® device latency (supports 1, 2 or 5ms configurable using Dante® Controller) · Independent input gain / output volume settings per channel. · Supports AES67 RTP audio transport contact support@blustream.com.au | support@blustream.co.uk 03 RevA3_User_Manual_DA44AU Front Panel 1 2 DA44AU USER MANUAL 3 45 6 7 8 9 10 1 Power Indicator LED - Illuminates when the unit is powered on 2 Input Indicator LED - Illuminates when an analogue audio signal is detected on the associated input into the unit 3 NET Indicator LED - Illuminates when the unit is receiving a Dante® network audio signal and audio is output 4 Link Indicator LED - Illuminates when the unit is connected to PC configuration software 5 48V Phantom Power Indicator LED - Illuminates when 48V phantom power is enabled on the associated input 6 Output Indiciator LED - Illuminates when a Dante® audio signal is being received and output via the assosiated output 7 LCD Display - Shows the status of network connection and menu selection 8 ESC Button - Escapes out of selected menu option 9 Rotary Dial / Enter Button - Rotate dial to scroll through selected menu item, press to select current menu item q Power button - Press to turn the unit on or off Rear Panel 1 2 3 4 5 1 Power Port Use included 12V/1A DC adaptor to power the device 2 Dante® Network Ports - 2 x RJ45 sockets to connect to Dante® network, note the DA44AU will only allow 1 network connection at a time, the device does not have two independent network interfaces. The 2nd RJ45 is for redundancy but can also be cascaded to additional DA44AU units (up to 7 x devices) 3 RS-232 Port 3-pin Phoenix connector to for control of the device from a computer or 3rd party control processor 4 4ch Audio Outputs - 12-pin Phoenix connector to connect to audio amplifier or mixing device, supports both balanced and unbalanced audio output from devices connected to the Dante® network (Note: will not output audio connected to the input of the same DA44AU device due to limitations of the Dante® Ultimo chipset) 5 4ch Audio Inputs - 12-pin Phoenix connector to connect to microphone or source audio device to convert the input signal to Dante® audio, supports both balanced and unbalanced signals including 48V phantom power 04 www.blustream.com.au | www.blustream.co.uk DA44AU USER MANUAL Audio Input Settings The DA44AU supports both line level input and microphone input including 48V phantom power. The input level sensitivity can also be adjusted to accomodate various source devices. This can be achieved through the front display menu, using the rotary dial, or via RS-232. The Audio Input Settings are as follows: CHANNEL A B C D INPUT TYPE Microphone Line SENSITIVITY 0dB 5dB 10dB 15dB 25dB 35dB -10dB 0dB PHANTOM POWER On Off Dante® Controller Dante® Controller software is required in order to setup and configure the DA44AU as well as control your Dante® network. Audinate provide extensive training videos and documentation on their website. This can be found here: http://www.audinate.com/products/software/dante-controller Upon connecting your DA44AU to a compatible network, the Dante® Controller software should automatically discover the device. The DA44AU will appear in the Dante® Controller with a name "DA44AU". On the "Routing" screen you can create audio routing between Dante® transmitters and receivers in your system. Note: It is not possible to route audio input into the DA44AU to an output within the same DA44AU due to limitation in the Dante® Ultimo chipset. contact support@blustream.com.au | support@blustream.co.uk 05 RevA3_User_Manual_DA44AU DA44AU USER MANUAL Dante® Controller By default the DA44AU is shipped with its network settings set to obtain an IP Address automatically. This means that if a DHCP server is present on your network, it will provide the DA44AU with an IP Address. If no DHCP server is present then the DA44AU will receive a default IP Address in the 169.254.xxx.xxx range. To change the IP Address of the DA44AU, you must enter the "Network Config" menu in the "Device Info" screen of the Dante® Controller software. Advanced Dante® Settings It is also possible to change various Dante® related settings of the DA44AU under the "Device Info" screen in the Dante® Controller software. To do so, select the "Device Config" menu. Here we can adjust the sample rate of the DA44AU. Please Note: That Dante® products can only transmit or receive audio from other Dante® products that are set up with the same sample rate. A mismatch in sample rate may stop audio from transmitting. Under the "Device Config" screen we can also adjust the latency of the DA44AU from 1, 2 or 5 milliseconds. 06 www.blustream.com.au | www.blustream.co.uk 07 RevA3_User_Manual_DA44AU DA44AU USER MANUAL Example Schematic DA44AU 4 x Mono | 2 x Stereo Outputs Recorder 4 x Mono | 2 x Stereo Inputs contact support@blustream.com.au | support@blustream.co.uk Cat 6 Analogue Audio RS-232 1G Network Switch Laptop | Dante® Controller Dante® Controller RS-232 Control Port The DA44AU can be controlled via a 3-pin Phoenix to serial RS-232 cable. The communication settings and commands are as follows: Baud Rate: 57600 bps Data Bit: 8-bit Parity: None Stop Bit: 1-bit Flow Control: None RS-232 COMMAND ? HELP STATUS RESET PRESET xx APPLY MUTE xx OUT yy IN xx AUD yy zz IN xx PHA yy RS232BAUD z NET DHCP ON/OFF NET IP xxx.xxx.xxx.xxx NET GW xxx.xxx.xxx.xxx NET SM xxx.xxx.xxx.xxx NET RB DESCRIPTION Print Help Information Print Help Information Print System Status And Port Status Reset System To Default Setting (Type "Yes" To Confirm, "No" To Discard) Apply Preset xx Mute On/Off Output yy xx= On or Off yy=[00]: All Output Ports, [01...04]: Output Port Set Mic/Line Input And Sensitivity xx=[00]: All Input Ports, [01...04]: Input Port yy=MIC or LINE zz=00: MIC: 00dB LINE: -10dB zz=01: MIC: 05dB LINE: 00dB zz=02: MIC: 10dB zz=03: MIC: 15dB zz=04: MIC: 25dB zz=05: MIC: 35dB Set Input Phantom Power On/Off xx=[00]: All Input Ports, [01...04]: Input Port yy= ON or OFF Set RS232 Baud Rate To z z = 1 2400, 2 4800, 3 9600, 4 19200, 5 38400, 6 57600 (default), 7 115200 Set Auto IP (DHCP) On Or Off Set IP Address Set Gateway Address Set Subnet Mask Address Reboot Network And Apply Default Config DA44AU USER MANUAL 08 www.blustream.com.au | www.blustream.co.uk DA44AU USER MANUAL Specifications Audio Input Connectors: 12-pin Phoenix connector (4ch balanced / unbalanced analogue audio / MIC) Audio Output Connectors: 2 x RJ45, female (1Gb Dante® network), 12-pin Phoenix connector (4ch balanced / unbalanced analogue audio / MIC) Dante® Audio Technology: Dante® Ultimo Casing Dimensions (W x H x D): 215mm x 44mm x 145mm without feet Shipping Weight: 1.6 Kg Operating Temperature: 32°F to 104°F (0°C to 40°C) Storage Temperature: - 4°F to 140°F (- 20°C to 60°C) Power Supply: 12V/1A DC Package Contents · 1 x DA44AU · 1 x User Manual · 1 x Mounting Kit · 1 x 12V/1A DC Power Supply Acknowledgements Dante® is a registered trademark of Audinate Pty Ltd. contact support@blustream.com.au | support@blustream.co.uk 09 RevA3_User_Manual_DA44AU Installer Notes: DA44AU USER MANUAL 10 www.blustream.com.au | www.blustream.co.uk Installer Notes: DA44AU USER MANUAL contact support@blustream.com.au | support@blustream.co.uk 11 www.blustream.co.uk www.blustream.com.au