Heath Zenith Wireless Plug-In Chime
Installation Instructions
This package includes a wireless plug-in chime and push button. The style of the push button and chime may vary from the illustration.
- Plug in the wireless chime. Ensure the power unit is oriented correctly in its vertical mount position. The plug is designed to fit the power outlet only as recommended by the manufacturer. Do not attempt to reverse the plug; this is a safety feature. If the plug does not insert fully, contact an electrician to replace the outlet.
- Test range. Temporarily position the push button where you intend to mount it. Press the push button to verify that the chime sounds and the push button works properly. If the chime does not sound, refer to the Troubleshooting section.
- Mount the push button. You can use either screws or double-sided tape for mounting.
- Screw Mounting: Remove the back of the case by inserting a small screwdriver into the slot on the top or bottom of the push button and twisting. Remove any material in the screw holes if needed before mounting. Attach the back of the case to the door jamb or wall. Snap the front of the push button into place.
- Tape Mounting: Ensure the surface of the door jamb or wall is clean before attaching the push button with double-sided tape.
Operation
The chime features adjustable volume, tune selection, and a mute function.
Chime Mute
Press and release the mute icon 🔔 (bell with a slash) to mute the chime. The chime will flash blue-green each time the push button is pressed while muted. Press and release the mute icon again to unmute the chime. The chime will flash green each time the push button is pressed when unmuted.
Volume Control
The chime has four adjustable volume levels. Press and release the volume control icon 🔊 (sound waves) to select the desired volume level.
Tune Selection
The chime has six different selectable tunes. Press and release the tune icon 🎵 (musical note) until the desired tune is heard. This tune will play each time the push button is pressed.
Available Tunes:
- Ding-Dong
- Westminster
- Whittington
- Auld Lang Syne
- Relax
- Beethoven's 5th
Troubleshooting
PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
- Press and hold the "Mute" icon on the chime for approximately 3 seconds. The chime will sound a "Beep-Beep" and flash green twice.
- Press the push button within 10 seconds. The chime will sound a "Beep-Beep" tone to indicate the push button is synced.
- Press the push button to ensure operation.
B. POSSIBLE CAUSE: Chime is not receiving power.
B. CORRECTIVE ACTION: Make sure the plug-in chime has power.
PROBLEM: Chime does not work after installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to move the push button away from the metal surface. Move the chime to a different wall outlet.
B. POSSIBLE CAUSE: Chime is mounted near a concrete floor or wall. Note: Concrete may reduce range.
B. CORRECTIVE ACTION: Move the chime away from the concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate the chime closer to the push button.
Note: The push button and chime come synced from the factory. The range of the wireless chime can vary with location, temperature, and battery condition.
One Year Limited Warranty
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge.
Not Covered: Repair service, adjustment, and calibration due to misuse, abuse, or negligence; light bulbs, batteries, and other expendable items are not covered. Damage to the light fixture from chemicals or pressure washers is not covered. Unauthorized service or modification of the product or its components will void this warranty.
This warranty does not cover reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. It covers only HeathCo LLC assembled products and not other equipment used with them.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIR OR REPLACEMENT IS THE SOLE REMEDY. HEATHCO LLC SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow limitations on incidental or consequential damages, so the above limitation may not apply.
Please keep your dated sales receipt, as it is required for all warranty requests.
HeathCo LLC reserves the right to discontinue and change specifications at any time without notice without incurring any obligation to incorporate new features into previously sold products.
Technical Service
Please contact HeathCo LLC for assistance before returning the product to the store.
If you experience a problem, follow the troubleshooting guide. You may also contact Technical Service between 8:00 AM and 5:00 PM CST (Monday-Friday).
When contacting Technical Service, please provide:
- Name
- Street Address
- Daytime Phone Number
- Email Address
- Model Number
- Date of Purchase
- Place of Purchase
- Product Issue
- DATED SALES RECEIPT FOR WARRANTY REQUESTS
No service parts are available for this product.
HeathCo LLC
P.O. Box 90045
2445 Nashville Road
Bowling Green, KY 42101, USA
ATTN: Technical Service
Internet: www.hzsupport.com
Phone: 1-800-858-8501 (English Only)
Fax: 1-270-846-8500
Regulatory Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-003 (B)/NMB-003 (B)
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The distance between user and products should be no less than 20 cm.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
Purchase Information
Please keep your dated sales receipt. It is required for all warranty requests.
Model #:
Date of Purchase:
Staple Purchase Receipt Here
