iDatalink - Home
Instruction Manual for idatalink models including: 2019, 2020, 2021, 2022, 2023, DL-CH12 Chrysler Pacifica Hybrid PTS, DL-CH12, Chrysler Pacifica Hybrid PTS, Pacifica Hybrid PTS, Hybrid PTS
FTI-CDP1 | MyFirstech Install
File Info : application/pdf, 4 Pages, 2.80MB
DocumentDocumentFTI-CDP1: Notas de preparación y cobertura del vehículo Make DL-CH12 Chrysler Model Pacifica Hybrid PTS Year 2019-23 Install Type 1C CAN F/JC Lights Park / Auto Type B2 IGN PINK RAP I/O Changes Green White/Blue NO N/A FIRMWARE: Esta instalación requiere BLADE-AL (DL) -CH12, módulo flash y actualización del firmware del controlador antes de la instalación. INSTALACIÓN: Los vehículos de tipo 1C utilizan un cable de extensión CAN para realizar las conexiones en el conector de unión del firewall, ubicado arriba el panel de protección del conductor y conectado al cortafuegos (CANH, pin # 57, marrón / blanco, CANL, pin # 58, amarillo). ENCENDIDO: El encendido Tipo 1C está disponible en el conector de unión ubicado sobre el panel de protección del conductor, conectado al firewall, El cable del vehículo está ubicado en el pin # 37, rosa / lt. verde, del conector de 59 pines. FTI-CDP1 - Notas de instalación y configuración A CONEXIÓN REQUERIDA (cable de extensión CAN) B NO SE REQUIERE (el arnés PUEDE) C SIN CONEXIÓN D CONEXIÓN REQUERIDA (IGN) IIIIIIIIIIIIIIIIIIIIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII D LAN 2001 O O Z K E R E D st. E IIIIIIIII S ID D KO O rG fo AD E R R E 'T T AN NC CE AND WHO O H W WANNA LEARN TO IIIIIIIII COBFEERATTUURRAE DCEOVFEURNACGIOENES CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) SECURE TAKEOVER DOOR STATUS TRUNK STATUS HOOD STATUS E-BRAKE STATUS TACH OUTPUT BRAKE STATUS GLOW PLUG STATUS PARKING LIGHTS HAZARD LIGHTS A/M CONTROL CM -900 FTI-CDP1 - DL-CH12 - Type 1C 2019-22 Chrysler Pacifica Hybrid PTS BLADE PWR pink/black C green pink 3 2 5 4 1 OBD-II connector 1 1 16 A B B PTS Button 2 ENGINE START STOP Headlight switch 3 AUTO RAP SHUTDOWN or *Not required Driver kick panel/firewall junction connector 4 Junction connector, above driver kick panel, attached to firewall 1 5 6 10 16 11 117 118 22 31 23 39 40 45 46 47 48 53 54 55 56 57 58 59 D Green - CAN Junction Block tan/white yellow pink/lt. green CAN Junction Block (above glove box) Green CAN-C Junction Block 5 HL Above Glove Box Códigos de error de programación de LED El LED del módulo parpadea en ROJO durante la programación 1x - Error de CAN 2x - Código clave no aprendido 3x - Sin ENCENDIDO 4x - Sin inmovilizador, comprobar CAN / llave 5x - Error de VIN, verifique el cableado CAN 6x - Ver error 4x 7x - Error de KLON 8x - Sin ENCENDIDO, verifique la conexión INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Patent No. US 8,856,780 CA 2759622 Page 40 of 43 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 MODULE PROGRAMMING PROCEDURE - PTS NOTE I IMPORTANT: The hood must be closed. 1 Close driver door. Re-open driver door to wake up data bus. 2 Press UNLOCK on OEM remote. (If the vehicle is not equipped with an OEM remote, press on the module programming button.) 3 Wait, LED will flash BLUE once [1x]. If LED does not flash GREEN, repeat step 2. 10 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 11 WARNING: Disconnect power last. Disconnect module from vehicle. 12 Connect module to computer and proceed with extended programming. 4 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 13 WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 5 6 OFF ACC ON START Wait, if LED turns solid RED proceed to step 6. If LED flashes BLUE rapidly, proceed to step 10. Set ignition to OFF position. ENGINE START STOP 14 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 15 Wait, LED will turn solid BLUE for 2 seconds. 7 Repeat steps 4 to 6, eight times [8x]. 8 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 16 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 17 Module Programming Procedure completed. 9 Wait, LED will flash BLUE rapidly. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Page 43 of 43 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - PTS - TO THE VEHICLE OWNER NOTE 2 I All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTI N COMING UP ! TIME RESTRICTI N Within 45 SECONDSfrom previous step: Open vehicle door. Enter vehicle. Close vehicle door. Press and release BRAKE pedal. 1 Unlock vehicle door using OEM or after-market remote, or door request switch. 3 Take over procedure completed. ! Failure to follow procedure will result in vehicle engine shutdown. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020