Dragonhawk Wireless Tattoo Gun Machine YZBTD Instruction Manual

1. Sissejuhatus

This manual provides detailed instructions for the safe and effective operation of your Dragonhawk Wireless Tattoo Gun Machine, Model YZBTD. Please read this manual thoroughly before using the device to ensure proper setup, operation, and maintenance. This machine is designed for professional tattoo artists and beginners, offering versatility and reliable performance.

2. Ohutusalane teave

Always prioritize safety when operating tattoo equipment. Failure to follow these guidelines may result in injury or damage to the device.

• Ainult välispidiseks kasutamiseks: This device is intended for tattooing on skin.
• Steriliseerimine: Ensure all needles, cartridges, and contact surfaces are properly sterilized before each use.
• Toiteallikas: Use only the provided charging cable and compatible power adapters.
• Aku ohutus: Do not expose batteries to extreme temperatures or puncture them. Dispose of used batteries responsibly.
• Käitlemine: Handle the machine with care. Avoid dropping or subjecting it to strong impacts.
• Niiskus: Keep the device dry. It is water-resistant, but not waterproof. Avoid submerging it in liquids.
• Lapsed: Hoida lastele kättesaamatus kohas.

3. Toote lõppview & Komponendid

The Dragonhawk Wireless Tattoo Gun Machine YZBTD is a cordless pen-style rotary tattoo machine featuring an adjustable stroke length and a powerful coreless motor.

Joonis 3.1: Üleview of the tattoo machine's control panel and battery.

Põhikomponendid:

• Masina korpus: Main housing containing the motor and drive system.
• Akupakett: Detachable power source with OLED display and control buttons.
• Reguleeritav käepide: Rotates to adjust needle depth.
• Stroke Adjustment Knob: Allows selection of 7 stroke lengths (2.4mm - 4.2mm).
• Needle Cartridge Slot: Where tattoo needle cartridges are inserted.
• C-tüüpi laadimisport: Aku laadimiseks.

4. Seadistamine

4.1 Aku paigaldamine

The machine comes with two replaceable batteries to ensure continuous operation.

1. Veenduge, et masin on välja lülitatud.
2. Gently twist the battery pack counter-clockwise to detach it from the machine body.
3. Align a charged battery pack with the machine body and twist clockwise until securely fastened.

Figure 4.1: The machine is equipped with two replaceable batteries for extended use.

4.2 Needle Cartridge Installation

Use only compatible Dragonhawk cartridge needles for optimal performance.

1. Valige soovitud nõelakassett.
2. Insert the needle cartridge into the machine's slot, pushing firmly until it clicks into place.
3. To remove, twist the cartridge slightly and pull it out.

Figure 4.2: Proper insertion of a needle cartridge into the machine.

5. Kasutusjuhised

Tõhusa töö tagamiseks tutvuge juhtpaneeliga.

Figure 5.1: Control panel and stroke adjustment.

5.1 Toide sisse/välja

• Vajutage ja hoidke all nuppu 'O' (Switch Button) for a few seconds to power the machine on or off.
• The OLED display will show the current voltage ja aku tase.

5.2 Helitugevuse reguleeriminetage

• Kasutage '+' (Voltage Increase Key) ja '-' (Voltage Reduction Key) buttons to adjust the voltage 0.1 V sammuga.
• Soovitatav voltage vahemik on 4V-12V.

5.3 Changing Mode (Liner/Shader)

• Vajutage nuppu 'M' (Switch Mode) button to switch between Liner (L) and Shader (S) gears.
• The machine automatically memorizes the voltage settings for each mode.

5.4 Löögipikkuse reguleerimine

The machine offers 7 adjustable stroke lengths from 2.4mm to 4.2mm.

• Rotate the adjustment knob located on the machine body to select the desired stroke length.
• Available lengths: 2.4mm, 2.7mm, 3.0mm, 3.3mm, 3.6mm, 3.9mm, 4.2mm.

Figure 5.2: Adjusting the stroke length by rotating the knob.

5.5 Ametlik tootevideo

6. Hooldus

6.1 Puhastamine

• Enne puhastamist ühendage alati toide lahti.
• Wipe the machine body with a soft, damp cloth and a mild disinfectant.
• Do not use abrasive cleaners or submerge the machine in liquid.
• Ensure no liquid enters the motor or charging port.

6.2 Laadimine

The machine is equipped with a Type-C charging port.

• Connect the provided Type-C cable to the charging port on the battery pack.
• Connect the other end to a compatible USB power adapter.
• Täislaadimine võtab aega umbes 1.5 tundi.
• The battery indicator on the OLED display will show charging status.

Figure 6.1: Type-C charging port on the battery pack.

6.3 Aku hooldus

• Aku eluea pikendamiseks vältige aku sagedast täielikku tühjendamist.
• Store the machine and spare batteries in a cool, dry place when not in use.
• If storing for an extended period, charge the batteries to about 50-60% capacity.

7. Veaotsing

Levinud probleemide ja nende lahenduste kohta vaadake allolevat tabelit.

8. Tehnilised andmed

Technical details of the Dragonhawk Wireless Tattoo Gun Machine YZBTD.

9. Garantii ja tugi

Dragonhawk is committed to providing high-quality products and excellent customer service.

• Toote katvus: Dragonhawk products typically include coverage for manufacturing defects. Please refer to your purchase documentation for specific warranty terms.
• Tehniline tugi: For video tutorials, setup guides, and professional tips, visit Youtube.com/@Dragonhawkofficial.
• Klienditeenindus: For any inquiries or issues with your order, please reach out through Amazon's messaging system.
• Tagastab: This product has a 30-day return policy for refund/replacement.