Manual de instrucciones del panel de instrumentos Metra DP-7528 DIN simple o doble
Tablero de instrumentos Metra DP-7528 DIN simple o doble

CARACTERÍSTICAS DEL KIT

  • Provisión de radio ISO DIN con bolsillo
  • ISO ODIN radio provision
  • Textured to match the factory dash.
  • Can also be used as a factory dash replacement with factory Mazda radios.

COMPONENTES DEL KIT

COMPONENTES DEL KIT

  • A) Carcasa de radio
  • B) Radio trim panel
  • C) Soportes de radio
  • D) bolsillo
  • E) Tornillos Phillips #8 x 3/8″ (10)
  • F) Clips de panel (2)
  • G) #8 x 1/2″ Phillips screws (2)

CONEXIONES DE CABLEADO Y ANTENA (se venden por separado)

Arnés de cableado: 70-7901
Visit metraonline.com for audio/video and steering
wheel control interface options.
Adaptador de antena: no es necesario

HERRAMIENTAS NECESARIAS

  • Herramienta de extracción de paneles
  • Destornillador Phillips

¡Atención! With the key out of the ignition, disconnect the negative battery terminal before Installing this product. Ensure that all Installation connections are secure before cycling the ignition to test this product.

DESMONTAJE DEL TABLERO

From the center console: 

  1. Unclip ashtray to reveal (1) Phillips screw and remove. (Figure A)
  2. Open storage compartment and remove (2) Phillips screws. (Figure B)
  3. Locate the (2) Phillips screws on the front sides of the gear shifter trim panel and remove. (Figure C )
    DESMONTAJE DEL TABLERO
  4. Unscrew gear shift knob. (Figure D)
  5. Unplug (2) connectors and remove the center console. (Figure E)
    DESMONTAJE DEL TABLERO

Del conjunto de radio de fábrica: 

  1. Unclip and remove center air vents to reveal (2) screws at the top of the radio trim panel. Remove the (2) screws. (Figure F)
  2. Unplug and remove the radio trim panel. (Figure G)
  3. Remove the (4) Phillips screws and pull out the radio assembly. (Figure H)
    DESMONTAJE DEL TABLERO
  4. Remove (2) Phillips screws from the support bar on top of radio trim. Save bar for kit preparation. (Figure I)
  5. Remove (2) Phillips screws to remove the hazard switch. Save switch for kit preparation. (Figure J)
  6. Remove (1) screw from each air vent retaining clip. Keep together for (Figure I) kit preparation. (Figure K)
    DESMONTAJE DEL TABLERO

PREPARACIÓN DEL KIT

  1. Secure the support bar to the top of the radio housing using the (2) screws removed in step 4. (Figure A)
  2. Secure the hazard switch using the (2) #8 x 1/2″ Phillips screws provided. (Figure B)
  3. Transfer the retaining clips to the corresponding locations on the radio housing using screws removed in step 6. (Figure C)
    PREPARACIÓN DEL KIT
  4. Attach the radio trlmplate to the radio housing using (6) of the supplied #8 x 3/8″ Philips screws. (Figure D)
  5. Attach the (2) panel clips to the radio housing. (Figure E)
    PREPARACIÓN DEL KIT

MONTAJE DEL KIT

Provisión de radio ISO DIN con bolsillo 

  1. Attach the pocket to the radio brackets using (4) of the supplied #8 x 3/8″ Phillips screws. (Figure A)
  2. Slide the radio into the bracket/pocket (iii. assembly and secure it using the screws supplied with the radio. (Figure B)
  3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra -~ and/or AXXESS.
  4. Slide the radio into the sub dash and secure it using the factory hardware.
  5. Reassemble the dash in reverse order of  (Figure 8) disassembly using the new 7528 radio housing.
    MONTAJE DEL KIT

ISO ODIN radio provision 

  1. Attach the radio brackets to the radio using the screws supplied with the  radio. (Figure A)
  2. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS.
  3. Slide the radio into the sub dash and secure it using the factory hardware.
  4. Reassemble the dash in reverse order of disassembly using the new 7528 radio housing.
    MONTAJE DEL KIT

¿Tienes dificultades? Estamos aquí para ayudar.

Código QR

Iconos  Comuníquese con nuestra línea de soporte técnico en:
386-257-1187
Iconos O por correo electrónico a:
[correo electrónico protegido]

Horas de soporte técnico (hora estándar del este) 

Lunes -Viernes: 9:00 AM – 7:00 PM
Saturday: 10:00 AM- 7:00 PM
Sunday: 10:00 AM -4:00 PM

logotipos EL CONOCIMIENTO ES PODER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school In our industry. Log onto www.installerinstituto.edu or call 386-672-5771 for more information and take stops toward a better tomorrow

logotipos Metra recommends MO certified technicians

Documentos / Recursos

Tablero de instrumentos Metra DP-7528 DIN simple o doble [pdf] Manual de instrucciones
DP-7528, Single or Double DIN Dash Panel, DP-7528 Single or Double DIN Dash Panel, Double DIN Dash Panel, DIN Dash Panel, Dash Panel, Panel

Déjame tu comentario

Tu dirección de correo electrónico no será publicada.