Milesight | 5G, AI, IoT and LoRaWAN®
User Guide for Milesight models including: GS601, GS601 Vape Detector, GS601, Vape Detector, Detector
Xiamen Milesight IoT Co., Ltd. GS601 2AYHY-GS601 2AYHYGS601 gs601
File Info : application/pdf, 4 Pages, 1.92MB
DocumentDocumentQUICK START GUIDE VAPE DETECTOR GS601 1. Packing List GS601 Sensor Ceiling Mounting Kits Type-C Cable & Power Adapter PoE Splitter (Optional) Quick Start Guide 2. Hardware Introduction Warranty Card NFC Area LED Indicator USB Type-C 3. Button and LED Descriptions Function Power On/Off Reboot Reset to Factory Default Alarm Action Connect to the power supply Disconnect power Press and hold reset button for over 3s Press and hold reset button for over 10s When one of the measured values exceeds the threshold When someone tampers the device Reset Button LED Indicator Static On Light Off Blinks Slowly Blinks Quickly Static On 4. Power Supply Powered by Power Adapter Powered by PoE Splitter (Optional) Type-C Cable (Power) Ethernet Cable (Power) PoE Splitter PoE Switch 5. Configuration 1. Download "Milesight ToolBox App"on an NFC-supported smartphone. Android iOS Quick Start Guide Milesight IoT Co., Ltd. www.milesight.com 2. Launch "Milesight ToolBox App" and attach the NFC area of smartphone to the device. Click "NFC Read" to read/write the device until App shows a successful prompt. It's suggested to configure a device password for security. (Default password: 123456) NFC 6. Installation Step 1: Step 2: Step 3: Step 4: Installation Note: Recommended installation height and environment: On the ceiling at a height of 2.4m to 3m in areas where smoking may occur. Avoid installing the device in areas where it may be exposed to liquid spray. The device's response speed is affected by the ambient airflow. It is recommended to install it in places where the airflow is stable, such as 30-50cm away from exhaust fans. Avoid installing it in places with unstable airflow, such as near doors/windows/ air conditioning vents/places directly blown by fans. Ensure a distance of more than 50cm, and the greater the wind force, the farther the distance would be. 50CM 30-50CM If there are no exhaust fans or other ventilation equipment in the installation environment, it is recommended to deploy devices within a detection range of a 1.5m radius. In an installation environment with partitions or dividers (like toilet): If the partitions or dividers extend to the ceiling, it is recommended to install one device in each partition or divider; If not, it is recommended to deploy devices according to the detection range of a 1.5m radius. 7. FCC Statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 8 . Specif icat ions 9 . Compliance In order to comply with RED RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times. Xiamen M ilesight IoT Co., Ltd. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/ 53 / EU. You can find the Declaration of Conformity on www.milesight.com support. This product is not restricted for use in European countries IQC GS601 1:1 63x63mm 84x84mm 120x85mm 80g 200g+80g V1.0 44.005.000437 mm GBT1804-f GBT1804-m GBT1804-c GBT1804-v / : 1. 2. V1.0 V2.0 V3.0 / / / /20240925 / /