HUNTER-logo

HUNTER Klein 19440 Light Pendant

HUNTER-Klein-19440-Light-Pendant-product

encimaview

HUNTER-Klein-19440-Light-Pendant-fig-1

INSTRUCCIONES DE INSTALACIÓN

ADVERTENCIA 

  • To avoid possible electrical shock, beforeinstalling your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location
  • El dispositivo de iluminación debe estar conectado a tierra. Si el cable a tierra para el lugar de instalación no está presente, DETENGA la instalación inmediatamente y consulte a un electricista calificado.
  • Todo el cableado debe estar de acuerdo con los códigos eléctricos nacionales y locales ANSI / NFPA 70. Si no está familiarizado con el cableado o tiene dudas, consulte a un electricista calificado.

LEA Y GUARDE ESTAS INSTRUCCIONES
Estas instrucciones se proporcionan para su seguridad. Es muy importante que se lean detenidamente y en su totalidad antes de comenzar la instalación del dispositivo de iluminación.

Aquí están las herramientas que necesitará para completar su instalación

HUNTER-Klein-19440-Light-Pendant-fig-3

PREPARACIÓN PARA LA INSTALACIÓN

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (H) should be attached to the mounting bracket (A) with a hex nut (G) in place. The other end should be connected to the canopy loop (E). Unscrew the canopy loop ring (F) from the canopy loop (E). Depending on the placement of your junction box the position of threaded post (H) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (D) over the canopy loop (E), so that it is flush with the ceiling. Adjust the position of threaded post (H) on the mounting bracket (A) so that the canopy (D) covers at least half of the exterior threads on the canopy loop  (E) while it is securely connected to threaded post (H). The threaded post (H) can be adjusted by loosening hex nut (G) to allow movement of threaded post (H) on mounting bracket (A). Once the ideal position of the threaded post (H) is determined, tighten up the hex nut (G) onto the threaded post (H) just beneath the mounting bracket (A) to secure the threaded post in place..

MONTAJE DEL APARATO

There are 4 12-inch rods (I), and 1 6-inch rod (J) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw rod onto threaded post (K) on the fixture. Pull the fixture wires through the canopy loop ring (F), top of canopy (D), and canopy loop (E). Screw the top rod to canopy loop (E). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

HUNTER-Klein-19440-Light-Pendant-fig-2

CONECTANDO LOS CABLES 
Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (C) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician

TERMINANDO LA INSTALACIÓN

Place the canopy (D) flush to the ceiling and slide the canopy loop ring (F) up beneath the canopy. Tightly screw canopy loop ring (F) onto the canopy loop (E) to properly secure the canopy (D) in place. Carefully install glass shade (M) over socket (L), then install socket cover (N) and tighten up the glass shade with socket ring (O). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattagmi. Su instalación ahora está completa. Encienda la alimentación y pruebe el accesorio.

CONSEJOS DE LIMPIEZA

¡Trate el accesorio con cuidado! La limpieza regular reducirá la necesidad de una limpieza profunda. Para una limpieza regular, apague la luz y limpie el aparato con un paño de microfibra o algodón limpio que no suelte pelusa. Nunca rocíe limpiador directamente sobre el aparato.

AVISO
In order to use a 12in rod by itself you must first remove the post from the 6in rod and install it on one of the ends of the 12in rod

Consejo profesional de Hunter 
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access

Documentos / Recursos

HUNTER Klein 19440 Light Pendant [pdf] Manual de instrucciones
Klein 19440, Klein, 19440, Light Pendant

Déjame tu comentario

Tu dirección de correo electrónico no será publicada.