Evjuicion Wallbox 7.4 kW Type 2 EV Charger Instruction Manual

1. Introducción

This manual provides detailed instructions for the installation, operation, and maintenance of your Evjuicion Wallbox 7.4 kW Type 2 Electric Vehicle (EV) Charger. This Level 2 charger is designed to provide efficient and reliable charging for your electric or hybrid vehicle. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.

Figure 1: Evjuicion Wallbox 7.4 kW Type 2 EV Charger in use, illustrating rapid charging capabilities.

2. Información de seguridad

Instrucciones de seguridad importantes:

• Lea todas las instrucciones antes de usar este producto.
• This device must be installed by a qualified electrician in accordance with all local and national electrical codes and regulations.
• Do not use if the charging cable or connector is damaged, frayed, or shows any signs of wear.
• Do not immerse the charger or cable in water or other liquids.
• Do not operate the charger in explosive or flammable environments.
• Ensure the charging cable is properly routed to prevent tripping hazards or damage.
• Mantenga a los niños alejados del área de carga durante el funcionamiento.
• Desconecte la alimentación antes de realizar cualquier mantenimiento o limpieza.

Figure 2: The Evjuicion Wallbox incorporates 8 layers of protection for safe and reliable charging, including safeguards against overcharges, thermal issues, ground faults, current leakage, high and low voltage, overloads, and lightning strikes.

3. Contenido del paquete

Verifique que todos los artículos enumerados a continuación estén incluidos en su paquete:

• 1 x EV Charger Unit (Evjuicion Wallbox 7.4 kW Type 2)
• 1 x placa de montaje
• 1 x Charging Cable (5 meters, integrated)
• 3 tornillos de cabeza plana
• 3 x Anclajes de expansión
• 3 x Round-head Self-tapping Screws
• 3 x Round-head Screws
• 1 x Manual de usuario (este documento)

4. Características del producto

The Evjuicion Wallbox 7.4 kW Type 2 EV Charger offers a range of features designed for convenience and efficiency:

• Carga rápida: Delivers up to 7.4 kW power, significantly reducing charging times compared to standard chargers.
• Corriente ajustable: Selectable current settings (6A, 8A, 10A, 13A, 16A, 32A) to optimize charging based on vehicle and grid capacity.
• Carga temporizada: Program charging start times up to 12 hours in advance to take advantage de tarifas eléctricas fuera de horas punta.
• Pantalla LED de 2.8 pulgadas: Proporciona información en tiempo real sobre la corriente, el volumentage, charging status, temperature, and more.
• RFID Access: Secure charging activation using RFID cards, preventing unauthorized use.
• Diseño duradero: IP65 rated for weather resistance, suitable for both indoor and outdoor installation, operating in temperatures from -20°C to +50°C.
• Gestión de cables integrada: Built-in cable holder for neat and organized storage of the 5-meter charging cable.
• Amplia compatibilidad: Compatible with 99% of EV and PHEV models adhering to the IEC 62196-2 standard (Type 2 connector).
• Protecciones múltiples: Equipped with 8 safety protections including overcharge, thermal, leakage, high/low voltage, and lightning protection.

Figure 3: The charger features intelligent current adjustment and delayed charging options, allowing users to optimize charging schedules for cost savings during off-peak hours.

Figure 4: Designed for all-weather reliability, the Evjuicion Wallbox is IP65 rated for water and dust resistance, and can withstand extreme temperatures from -20°C to +50°C.

Figure 5: The charger offers wide compatibility with most EV and PHEV models, supporting Type 2 and CCS2 standards, ensuring hassle-free charging for a broad range of vehicles.

5. Configuración e instalación

The Evjuicion Wallbox can be installed on a wall or a dedicated charging column. Professional installation by a qualified electrician is highly recommended to ensure compliance with electrical codes and safety standards.

5.1 Installation Steps (Wall Mount Example)

1. Prepare el sitio de instalación: Choose a suitable location near your parking spot, ensuring it is protected from direct impact and has access to the main electrical supply.
2. Desconectar la energía: Antes de comenzar cualquier trabajo eléctrico, asegúrese de que el suministro de energía principal al área de instalación esté apagado en el disyuntor.
3. Instalación de la placa de montaje:
   • Use the included mounting plate as a template to mark the drilling points on the wall.
   • Drill holes at the marked positions. Insert the expansion anchors into the drilled holes.
   • Secure the mounting plate to the wall using the flat-head screws.
4. Conexión eléctrica:
   • Remove the back cover of the charger unit.
   • Connect the AC power supply wires to the designated terminals inside the charger. Ensure correct polarity (Live, Neutral, Ground).
   • Secure all wiring connections firmly.
   • Vuelva a colocar la cubierta trasera.
5. Conecte la unidad de carga: Carefully align the charger unit with the mounted plate and secure it using the remaining screws (round-head self-tapping and round-head screws).
6. Comprobaciones finales: Double-check all connections and ensure the unit is securely mounted.
7. Restaurar energía: Turn on the main power supply at the circuit breaker. The charger's LED display should illuminate.

Note: For column installation, follow similar steps, adapting to the specific column mounting hardware.

6. Instrucciones de funcionamiento

6.1 Understanding the LED Display and Indicators

Figure 6: The 2.8-inch LED display provides real-time monitoring of charging parameters and status indicators. A solid blue light indicates standby or charge completion, while a flashing green light signifies active charging.

The 2.8-inch LED display shows critical charging information. Familiarize yourself with the following indicators:

• Corriente (A): Displays the charging current in AmpEres.
• Volumentagmi(V): Muestra el volumen actualtage.
• Potencia (kW): Indicates the charging power in kilowatts.
• Temperatura (°C): Displays the internal temperature of the charger.
• Estado de carga: Icons indicate if charging is active, paused, or complete.
• Carga programada: Indicates if a timed charging session is set.
• Luz indicadora LED:
  • Azul solido: Charger is in standby mode or charging is complete.
  • Verde intermitente: Charger is actively charging the vehicle.
  • Rojo: Indicates an error or fault. Refer to the Troubleshooting section.

6.2 Iniciar una sesión de carga

1. Connect the Vehicle: Plug the Type 2 connector firmly into your vehicle's charging port. Ensure a secure connection.
2. Activate with RFID Card: Hold your RFID card over the designated RFID reader area on the charger. The charger will beep, and the LED display will show "RFID OK" or similar confirmation. Charging will begin automatically.
3. Carga del monitor: Observe the LED display for real-time charging data and the flashing green indicator light.

Figure 7: The 5-meter charging cable provides flexibility, and charging is securely activated using an RFID card to prevent unauthorized use.

6.3 Ajuste de la corriente de carga

You can adjust the charging current (Amperage) to suit your needs or vehicle's requirements. This can help prolong battery life or manage grid load.

1. Before or during a charging session, press the "A" button (Amperage adjustment) on the charger's control panel.
2. Each press will cycle through the available current settings: 6A, 8A, 10A, 13A, 16A, 32A.
3. Select your desired current. The display will update to reflect the new setting.

6.4 Setting Timed Charging

To schedule a delayed start for your charging session (e.g., for off-peak hours):

1. Conecte el cable de carga a su vehículo.
2. Press the "Clock" button (Timed Charging) on the charger's control panel.
3. Each press will increase the delay time in 1-hour increments, from 0 to 12 hours.
4. Once the desired delay is set, the charger will wait for that duration before automatically starting the charging session.
5. You can still use the RFID card to override the timer and start charging immediately if needed.

6.5 Detener una sesión de carga

1. Via Vehicle: Most EVs allow you to stop charging from within the vehicle's infotainment system or app.
2. A través del cargador: If your vehicle does not release the cable automatically, you may need to use the RFID card again to stop the session and unlock the connector.
3. Desconectar: Once charging has stopped and the cable is unlocked, safely disconnect the Type 2 connector from your vehicle.
4. Cable de la tienda: Return the charging cable to its integrated storage position on the charger.

7. Mantenimiento

Regular maintenance ensures the longevity and safe operation of your Evjuicion Wallbox.

• Limpieza:
  • Asegúrese de que el cargador esté apagado antes de limpiarlo.
  • Limpie el exterior del cargador con un paño suave y húmedo.amp Paño. No utilice limpiadores abrasivos, disolventes ni productos químicos agresivos.
  • Keep the charging connector free from dust, dirt, and moisture.
• Inspección de cables:
  • Periodically inspect the charging cable and connector for any signs of damage, cuts, fraying, or discoloration.
  • If any damage is found, discontinue use immediately and contact customer support.
• Almacenamiento de cables: Always store the charging cable neatly using the integrated cable management system when not in use to prevent damage and tripping hazards.

Figure 8: The integrated cable management system ensures the charging cable is stored cleanly, organized, and practically, preventing tangles and maintaining a tidy charging area.

8. Solución de problemas

Si tiene problemas con su Evjuicion Wallbox, consulte los siguientes problemas y soluciones comunes:

Si el problema persiste después de intentar estas soluciones, comuníquese con el servicio de atención al cliente de Evjuicion para obtener más ayuda.

9. Especificaciones

10. Garantía y soporte

Información de garantía:

Evjuicion products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Evjuicion webSitio. Conserve su comprobante de compra para reclamaciones de garantía.

Atención al cliente:

If you have any questions, require technical assistance, or need to report a problem with your Evjuicion Wallbox, please contact our customer support team. Contact details can typically be found on the product packaging, the official Evjuicion websitio, o a través de su minorista.

When contacting support, please have your product model number (ZAU207C-CS) and purchase date available.