AQUASTRONG Sand Filter Pump SFPV121T Instruction Manual

1. Introducción

This manual provides essential information for the safe installation, operation, and maintenance of your AQUASTRONG Sand Filter Pump. This 2/3 HP pump with a 12-inch filter and 6-way valve is designed for above-ground pools up to 11,000 gallons, offering a powerful 3000 GPH flow rate and a programmable 24-hour timer for optimal water clarity.

Please read this manual thoroughly before attempting to install or operate the pump. Keep this manual for future reference.

Figure 1: AQUASTRONG 12-inch Sand Filter Pump with Timer. This image displays the complete sand filter pump unit, highlighting its compact design and integrated timer feature.

2. Información de seguridad

Always follow basic safety precautions to reduce the risk of injury, fire, electric shock, or property damage.

• Seguridad eléctrica: Ensure the pump is connected to a grounded outlet protected by a Ground Fault Circuit Interrupter (GFCI). Do not operate the pump if the power cord is damaged.
• Seguridad del agua y de los productos químicos: Never operate the pump without water. Always turn off the pump before performing any maintenance or adjustments. Handle pool chemicals with care and follow manufacturer instructions.
• Seguridad de presión: The filter operates under high pressure. Do not attempt to open the filter or service the pump while it is running. Ensure all clamps and connections are secure before operation.
• Niños: Keep children away from the pump and filter area.
• Instalación: Install the pump on a solid, level surface, away from the pool edge, ensuring proper ventilation.

3. Contenido del paquete

Verifique que todos los componentes estén presentes y sin daños antes de comenzar la instalación:

• AQUASTRONG Sand Filter Tank
• Pump Motor Assembly (2/3 HP)
• Válvula multipuerto de 6 vías
• Manómetro
• Hose Adapters (1.5-inch and 1.25-inch)
• Manguera Clamps
• Plato base
• Manual de instrucciones

4. Configuración e instalación

4.1 Colocación

Position the filter pump on a firm, level surface, preferably concrete or a sturdy base. Ensure it is located below the pool's water level for optimal priming and within reach of a grounded electrical outlet. Allow sufficient space around the unit for maintenance and access.

4.2 Adición de medios filtrantes

1. Retire la válvula multipuerto de la parte superior del tanque del filtro.
2. Cover the standpipe opening inside the tank to prevent sand from entering.
3. Carefully pour the recommended amount of filter sand (typically 50 lbs) or filter balls (1.5 lbs) into the tank.
4. Ensure the sand/filter balls are evenly distributed.
5. Remove the standpipe cover and clean any sand from the tank's rim.

Figure 2: Six-Way Valve Functions and Filter Media Capacity. This image illustrates the various settings of the 6-way valve and indicates the capacity for 1.5 lbs of filter balls or 50 lbs of sand.

4.3 Conexión de mangueras

1. Attach the multi-port valve to the filter tank, ensuring a tight seal.
2. Connect the pool's skimmer/drain hose to the pump's inlet.
3. Connect the pump's outlet to the multi-port valve's 'PUMP' port.
4. Connect the multi-port valve's 'RETURN' port to the pool's return jet.
5. Connect a backwash hose to the 'WASTE' port if desired.
6. Use the provided 1.5-inch or 1.25-inch hose adapters and clamps para asegurar todas las conexiones.

Figure 3: Hose Adapter Compatibility. This image demonstrates the use of 1.25-inch and 1.5-inch hose adapters, ensuring compatibility with various above-ground pool types, including Intex and Bestway.

Figure 4: Filtering Plan Diagram. This diagram illustrates the water flow: (1) Unfiltered water from the pool enters the pump, (2) Clean water returns to the pool after filtration, and (3) Waste water exits through the waste port.

4.4 Cebado de la bomba

Before starting, ensure the pool is filled to the proper level and all valves are open. The pump must be primed by filling it with water until water flows out of the return line. This removes air from the system and prevents dry running.

5. Instrucciones de funcionamiento

5.1 6-Way Multi-Port Valve Functions

The multi-port valve allows you to control the water flow for different operations. Siempre apague la bomba antes de cambiar la posición de la válvula.

• FILTRAR: Modo de filtrado normal. El agua fluye a través del medio filtrante y regresa a la piscina.
• RESACA: Invierte el flujo de agua para limpiar el medio filtrante. El agua se descarga por el puerto de desagüe.
• ENJUAGUE: Used after backwashing to flush out any remaining dirt from the filter media before returning to FILTER mode. Water is discharged through the waste port.
• DESPERDICIAR: Bypasses the filter, sending water directly out the waste port. Useful for vacuuming heavy debris or lowering pool water level.
• RECIRCULAR: Evita el filtro y devuelve el agua directamente a la piscina. Útil para la distribución de productos químicos sin necesidad de filtrar.
• CERRADO: Shuts off all flow to the filter and pump. Use for pump or filter maintenance.

5.2 Configuración del temporizador programable de 24 horas

The integrated timer allows you to automate filtration cycles for 2 to 24 hours. Refer to the timer's specific instructions for detailed programming steps. Generally, you will set the desired operating duration and the start time. The pump will automatically turn on and off according to your settings.

Figure 5: Built-in Automatic Timer. This image shows a user adjusting the integrated automatic timer on the pump, demonstrating its ease of use for scheduling filtration cycles.

5.3 Puesta en marcha de la bomba

1. Ensure the pump is primed and all connections are secure.
2. Set the multi-port valve to the 'FILTER' position.
3. Plug the pump into a grounded GFCI outlet.
4. Turn on the pump. Water should begin to circulate.
5. Check the pressure gauge. A rising pressure indicates the filter is collecting debris and may require backwashing soon.

6. Mantenimiento

6.1 Retrolavado y enjuague

Backwash the filter when the pressure gauge reads 8-10 PSI above its clean starting pressure, or when water flow to the pool noticeably decreases.

1. Apague la bomba.
2. Set the multi-port valve to 'BACKWASH'.
3. Turn on the pump and backwash until the water running through the sight glass (if present) is clear (typically 2-3 minutes).
4. Apague la bomba.
5. Set the multi-port valve to 'RINSE'.
6. Encienda la bomba y enjuague durante 30 a 60 segundos.
7. Apague la bomba.
8. Set the multi-port valve back to 'FILTER' and restart the pump.

6.2 Filter Media Replacement

Filter sand typically needs replacement every 3-5 years, depending on usage and water quality. Filter balls may last longer but should be inspected annually. Refer to the filter media manufacturer's guidelines.

6.3 Preparación para el invierno

Before freezing temperatures, drain all water from the pump, filter, and hoses. Disconnect and store the pump and filter in a dry, protected area. Remove the pressure gauge and drain plugs from the filter tank.

7. Solución de problemas

Esta sección aborda problemas comunes que puede encontrar con su bomba de filtro de arena.

8. Especificaciones

Figure 6: Performance Specifications. This image highlights the pump's performance metrics: 2/3 HP, 3000 GPH pump flow rate, 2200 GPH system flow rate, and suitability for pools up to 11,000 gallons.

• Número de modelo: SFPV121T
• Caballos de fuerza de la bomba: 2 / 3 HP
• Tasa de flujo de la bomba: 3000 GPH (galones por hora)
• Caudal del sistema: 2200 GPH
• Max Pool Capacity: Hasta 11,000 galones (aprox. 34,000 litros)
• Tamaño del tanque del filtro: 12 pulgadas de diámetro
• Tipo de válvula: Válvula multipuerto de 6 vías
• Minutero: 24-hour Programmable
• Compatibilidad de mangueras: 1.5-inch y 1.25-inch
• Fuente de energía: Cable eléctrico
• Dimensiones del producto (L x An x Al): 55.88 x 40.64 x 38.1 cm (22 x 16 x 15 pulgadas)
• Peso del producto: 13.2 kg (29.1 libras)
• Material: Componentes de plástico y metal duraderos

9. Garantía y soporte

The AQUASTRONG Sand Filter Pump (Model SFPV121T) comes with a garantía de dos años from the date of purchase, covering manufacturing defects. This warranty does not cover damage due to improper installation, misuse, neglect, or normal wear and tear.

For technical support, warranty claims, or replacement parts, please contact AQUASTRONG customer service. Contact details can typically be found on the product packaging or the official AQUASTRONG websitio.