VEVOR 80 CFM Bathroom Exhaust Fan User Manual

1. Introducción

Thank you for choosing the VEVOR 80 CFM Bathroom Exhaust Fan. This manual provides essential information for the safe installation, operation, and maintenance of your new ventilation fan. Please read it thoroughly before use and retain it for future reference.

This high-efficiency exhaust fan is designed to provide superior ventilation, reduce humidity, eliminate odors, and prevent fogging in bathrooms up to 85 sq.ft. It features an integrated LED light with adjustable color temperatures and operates quietly for a comfortable environment.

2. Información de seguridad

ADVERTENCIA: Para reducir el riesgo de incendio, descarga eléctrica o lesiones a personas, tenga en cuenta lo siguiente:

• Lea todas las instrucciones antes de instalar o realizar mantenimiento a este ventilador.
• Always disconnect power at the service panel before wiring or servicing.
• Esta unidad debe estar conectada a tierra.
• El trabajo de instalación y el cableado eléctrico deben ser realizados por personas calificadas de acuerdo con todos los códigos y estándares aplicables, incluidos los códigos y estándares de construcción con clasificación contra incendios.
• Se necesita suficiente aire para la correcta combustión y evacuación de gases a través de la chimenea de los equipos de combustión, a fin de evitar el reflujo de aire. Siga las directrices y normas de seguridad del fabricante del equipo de calefacción, como las publicadas por la Asociación Nacional de Protección contra Incendios (NFPA), la Sociedad Americana de Ingenieros de Calefacción, Refrigeración y Aire Acondicionado (ASHRAE) y las autoridades locales competentes.
• Al cortar o perforar la pared o el techo, no dañe el cableado eléctrico ni otros servicios públicos ocultos.
• Los ventiladores canalizados siempre deben ventilarse hacia el exterior.
• No utilice este ventilador con ningún dispositivo de control de velocidad de estado sólido.
• Este ventilador está diseñado únicamente para ventilación general. No lo utilice para extraer materiales y vapores peligrosos o explosivos.
• Para evitar daños en los cojinetes del motor e impulsores ruidosos y/o desequilibrados, mantenga el rociado de paneles de yeso, el polvo de construcción, etc. fuera de la unidad de potencia.
• This product is designed for ceiling mount installation only.

3. Contenido del paquete

Verifique que todos los componentes estén presentes y sin daños antes de comenzar la instalación.

• 1 x VEVOR Bathroom Exhaust Fan (Model: BT-BPT190AL)
• 1 x Double Switch (Includes 2 switch installation screws)
• 1 x Manual de usuario (este documento)
• 4 x Flat Head Screws M4*30mm

Image: VEVOR Bathroom Exhaust Fan, showing its dimensions and the included components like the double switch, user manual, and screws.

4. Especificaciones

Imagen: Más alláview of the VEVOR 80 CFM Bathroom Exhaust Fan.

5. Configuración e instalación

This exhaust fan is designed for easy ceiling-mounted installation, often without the need for attic access. Follow these steps carefully.

5.1 Prepare the Ceiling Opening

1. Mark and cut a ceiling opening of 7.68 x 7.6 inches (195 x 193 mm). Ensure there are no electrical wires or other obstructions in the cutting area.

Image: Visual guide showing the six main steps for installing the VEVOR Bathroom Exhaust Fan, including preparing the opening, securing the fan, connecting wiring, installing ductwork, attaching the panel, and final installation.

5.2 Secure the Exhaust Fan

2. Insert the exhaust fan into the prepared ceiling opening.
3. Secure the fan housing to a ceiling joist or beam using the provided screws. Ensure the fan is firmly mounted to prevent vibration and noise.

5.3 Cableado eléctrico

IMPORTANTE: Todo el cableado debe cumplir con los códigos eléctricos locales. Si tiene dudas, consulte a un electricista cualificado.

4. Connect the fan's wiring to your household wiring. Match the corresponding wire colors:
   • Negro (en vivo) a negro (en vivo)
   • Blanco (neutro) a blanco (neutro)
   • Green (Ground) to Green (Ground)
   Use appropriate wire connectors (not included) to secure connections.
5. If using the included double switch, connect the fan and light wires to the switch terminals as per the switch wiring diagram.

5.4 Install Ductwork

6. Connect a 4-inch exhaust duct (not included) to the fan's duct connector. Secure it with tape or clamps to ensure an airtight seal.
7. Route the ductwork to an exterior vent cap. Ensure the duct run is as short and straight as possible to maximize airflow efficiency.

5.5 Attach the Decorative Panel

8. Connect the lighting wire from the fan housing to the decorative panel's light connector.
9. Carefully snap the decorative panel onto the fan housing. Ensure it is flush with the ceiling.

Image: The VEVOR Bathroom Exhaust Fan installed in a modern bathroom, showcasing its minimalist white design that blends with various ceilings.

6. Instrucciones de funcionamiento

Once installed, the VEVOR Bathroom Exhaust Fan is ready for operation.

6.1 Fan and Light Control

• Use the included double wall switch to independently control the fan and the LED light. One switch operates the fan, and the other operates the light.
• The fan operates at a single speed (80 CFM).

Image: The VEVOR Bathroom Exhaust Fan's LED light displaying three adjustable color temperatures: Warm Color (3000K), Neutral Color (4000K), and Cool Color (5000K), providing 900 lumens of illumination.

6.2 Adjusting LED Color Temperature

The LED light offers three color temperature options (3000K, 4000K, 5000K). To cycle through these options, quickly toggle the light switch OFF and ON. The light will change to the next color temperature in sequence.

6.3 Uso óptimo

• For effective moisture and odor removal, operate the fan during and after showering or bathing for at least 15-20 minutes.
• The fan's quiet operation (1.5 Sones / 33 dB) ensures minimal disturbance.

Image: Graphic illustrating the low noise operation of the VEVOR Bathroom Exhaust Fan, showing its sound level at 33dB (1.5 Sones) compared to other common sounds.

7. Mantenimiento

Regular maintenance ensures optimal performance and extends the lifespan of your exhaust fan. Always disconnect power before performing any maintenance.

7.1 Limpieza de la rejilla y la cubierta de la luz

• Remove the decorative panel by gently pulling it down.
• Limpie la rejilla y la cubierta de la luz con un paño suave.ampenjuagado con agua y jabón suave. No utilice limpiadores abrasivos.
• Ensure the parts are completely dry before reattaching.

7.2 Cleaning the Fan Blades and Motor

• With the power disconnected, carefully reach into the fan housing.
• Wipe the fan blades and motor housing with a damp cloth. Avoid getting water directly into the motor.
• The all-copper motor is designed for durability and stable performance.

Image: Diagram showing the internal components of the VEVOR Bathroom Exhaust Fan, highlighting the high-quality all-copper motor and lightweight plastic PPFR blades, emphasizing powerful yet quiet operation.

7.3 Housing Durability

The galvanized steel housing provides excellent moisture and corrosion resistance, ensuring durability in humid bathroom environments.

Image: The VEVOR Bathroom Exhaust Fan shown in a humid shower environment, illustrating its galvanized steel housing and resistance to moisture and corrosion.

8. Solución de problemas

9. Garantía y soporte

Los productos VEVOR están diseñados para ofrecer durabilidad y rendimiento. Para obtener información sobre la garantía y soporte técnico, consulte el sitio web oficial de VEVOR. websitio o comuníquese directamente con su servicio de atención al cliente.

• Oficial Websitio: www.vevor.com
• Página de soporte: www.vevor.com/support

Please have your model number (BT-BPT190AL) and purchase date available when contacting support.