Aigo AC SE 120 Water Cooler Instruction Manual

1. Introducción

Thank you for choosing the Aigo AC SE 120 Water Cooler. This All-in-One (AIO) liquid cooling system is designed to provide efficient thermal management for your CPU, ensuring stable performance and extended component lifespan. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting.

Please read this manual thoroughly before installation and use to ensure proper setup and to prevent any damage to your system.

2. Información de seguridad

• Desconecte siempre la alimentación de su computadora antes de instalar o realizar mantenimiento en cualquier componente.
• Manipule los componentes con cuidado para evitar dañarlos.
• Use una pulsera antiestática para evitar daños por descarga electrostática (ESD) en componentes sensibles.
• Do not open the sealed liquid cooling loop. Tampering with the unit may cause leaks and void your warranty.
• Asegúrese de que todos los cables estén conectados y enrutados correctamente para evitar interferencias con piezas móviles (por ejemplo, aspas del ventilador).
• Mantener fuera del alcance de los niños.

3. Contenido del paquete

Verifique que todos los componentes estén presentes y en buenas condiciones antes de continuar con la instalación.

• Aigo AC SE 120 Water Cooler Unit (Pump, Radiator, Fan pre-installed)
• Mounting Hardware for Intel Sockets (LGA 2066/ 2011-v3 / 2011 / 1700 / 1366 / 1200 / 115X)
• Mounting Hardware for AMD Sockets (FM1 / FM2 / FM2+ / AM2 / AM2+ / AM3 / AM3+ / AM4)
• Pasta térmica (preaplicada o en tubo)
• Manual de usuario

Image: Aigo AC SE 120 Water Cooler unit with its fan, radiator, pump, and various mounting brackets and screws for different CPU sockets.

4. Especificaciones

5. Configuración e instalación

This section outlines the general steps for installing your Aigo AC SE 120 Water Cooler. Specific steps may vary slightly depending on your motherboard and PC case. Always refer to your motherboard and case manuals for detailed instructions.

5.1 Preparar el zócalo de la CPU

1. Zócalos Intel: Attach the correct Intel backplate to the rear of your motherboard. Secure the standoffs through the motherboard holes from the front.
2. Zócalos AMD: The cooler typically uses the existing AMD backplate. Remove the plastic retention clips from the stock AMD cooler mount, leaving the backplate in place. Install the appropriate AMD standoffs.
3. Asegúrese de que la CPU esté colocada correctamente en su zócalo.
4. Clean the CPU surface with isopropyl alcohol to remove any old thermal paste or residue.
5. Apply a thin, even layer of thermal paste to the center of the CPU's integrated heat spreader (IHS). If thermal paste is pre-applied to the water block, skip this step.

5.2 Install the Radiator and Fan

1. Determine the optimal mounting location for the 120mm radiator in your PC case. Common locations include the rear exhaust or top exhaust.
2. Mount the 120mm fan to the radiator using the provided screws. Ensure the fan is oriented to push or pull air in the desired direction (e.g., exhaust air out of the case).
3. Secure the radiator assembly to your PC case using the appropriate screws.

Imagen: Lateral view of the Aigo AC SE 120 Water Cooler, showing the radiator with a white fan attached, and the pump/water block unit.

5.3 Montar el bloque de agua

1. Attach the correct mounting brackets to the water block/pump unit.
2. Carefully place the water block onto the CPU, aligning the mounting holes with the standoffs.
3. Secure the water block with the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Image: The Aigo AC SE 120 Water Cooler showing the pump unit with an illuminated Aigo logo and a rainbow-colored fan on the radiator.

5.4 Conecte los cables

1. Connect the pump power cable to a dedicated AIO_PUMP or CPU_FAN header on your motherboard. If your motherboard has neither, use a SYS_FAN header and ensure it is set to run at full speed in the BIOS.
2. Connect the fan power cable to the CPU_FAN header on your motherboard. If your motherboard has multiple fan headers, consult your motherboard manual for the recommended CPU fan header.
3. If your cooler has RGB lighting, connect the RGB cable to a compatible RGB header on your motherboard (e.g., 3-pin ARGB or 4-pin RGB, depending on the cooler's connector type).
4. Route all cables neatly to avoid obstructing airflow or interfering with other components.

6. Instrucciones de funcionamiento

Once installed, the Aigo AC SE 120 Water Cooler operates automatically based on your motherboard's fan control settings.

• Encendido inicial: After installation, power on your computer. The pump and fan should start operating.
• Configuración de BIOS/UEFI: Access your motherboard's BIOS/UEFI settings to ensure the CPU_FAN and AIO_PUMP headers are configured correctly. It is recommended to set the pump header to run at full speed (100%) for optimal cooling performance. Fan speeds can be adjusted based on temperature curves for a balance of cooling and noise.
• Iluminación RGB: If connected to an RGB header, the lighting effects can typically be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync).
• Escucha: Use system monitoring software to check CPU temperatures and ensure the cooler is functioning effectively.

Imagen: de arriba hacia abajo view of the Aigo AC SE 120 Water Cooler, highlighting the illuminated Aigo logo on the pump and the rainbow lighting of the fan.

7. Mantenimiento

Regular maintenance helps ensure optimal performance and longevity of your water cooler.

• Limpieza de polvo: Limpie periódicamente las aletas del radiador y las aspas del ventilador para evitar la acumulación de polvo, que puede dificultar el flujo de aire y reducir la eficiencia de refrigeración. Utilice aire comprimido o un cepillo suave.
• Inspección del ventilador: Check the fan for any signs of wear, damage, or excessive noise. Replace if necessary.
• Inspección de manguera: Visually inspect the hoses for any kinks, cracks, or signs of leakage. While AIOs are sealed, regular checks are recommended.
• Pasta térmica: The thermal paste typically lasts for several years. If you notice a significant increase in CPU temperatures over time, consider reapplying fresh thermal paste. This requires carefully removing the water block, cleaning both surfaces, and applying new paste.

8. Solución de problemas

If you encounter issues with your Aigo AC SE 120 Water Cooler, refer to the following common problems and solutions:

9. Garantía y soporte

The Aigo AC SE 120 Water Cooler comes with a Garantía de 12 meses Desde la fecha de compra. Esta garantía cubre defectos de fabricación y mal funcionamiento en condiciones normales de uso.

La garantía no cubre:

• Daños causados ​​por instalación incorrecta, mal uso, abuso o negligencia.
• Daños causados ​​por modificaciones o reparaciones no autorizadas.
• Daños causados ​​por desastres naturales o accidentes.

For technical support, warranty claims, or further assistance, please contact your retailer or the Aigo customer service department. Please have your proof of purchase and product model number (ACSE120-BK) ready when contacting support.