SIMON 10 Series 230V Wall Switch and Commutator Instruction Manual

1. Producto terminadoview

The SIMON 10 Series white switch/commutator is an electrical control device designed for interior use. It can function as a standard ON/OFF switch or as a two-way commutator, allowing control of a single light point from two different locations. This product is supplied as a pre-assembled unit, including the mechanism, cover, and frame, to facilitate installation. Its robust design features screw-fastened components and a metallic frame for enhanced durability and secure mounting. The minimalist design with straight lines ensures seamless integration into various interior aesthetics.

Figura 1: Frente view of the SIMON 10 Series white wall switch and commutator.

2. ¿Qué hay en la caja?

The SIMON 10 Series switch/commutator package includes the following components:

• Mecanismo
• Cubrir
• Marco

3. Especificaciones

4. Información de seguridad

WARNING: Electrical installation should only be performed by qualified personnel. Failure to follow these instructions can result in electric shock, fire, or serious injury.

• Always disconnect power at the main circuit breaker or fuse box before attempting any installation, maintenance, or repair.
• Verifique que la energía esté apagada usando un vol.tagE probador antes de tocar cualquier cable.
• Siga todos los códigos y regulaciones eléctricas locales y nacionales.
• Do not install or operate with wet hands or in damp condiciones.
• Asegúrese de que haya una conexión a tierra adecuada cuando sea necesario.
• No exceda el volumen especificadotage (230V) or current rating (10A).

5. Configuración e instalación

The SIMON 10 Series switch/commutator is designed for straightforward installation. Please ensure you have read and understood the safety information before proceeding.

1. Desconectar la energía: Turn off the power supply to the circuit at the main circuit breaker or fuse box. Confirm power is off with a voltage probador.
2. Preparar el cableado: Carefully remove the existing switch or cover plate. Identify the live, neutral, and ground wires (if applicable) according to local wiring standards. For a commutator, identify the common wire and the two traveler wires.
3. Conectar cables: Using a screwdriver, connect the electrical wires to the screw terminals on the back of the SIMON 10 Series mechanism. Ensure all connections are secure and no bare wire strands are exposed. Refer to the wiring diagram below for typical connections.


Figura 2: Atrás view of the switch mechanism with screw terminals for wiring.

4. Mecanismo de montaje: Gently push the wired mechanism into the wall box. Use the metallic claws and mounting screws to secure the mechanism firmly to the wall box. The metallic claws provide better adhesion.

Figura 3: Explosión view showing mechanism, frame, and cover assembly.
5. Attach Frame and Cover: Position the polypropylene frame over the mounted mechanism. The flexible nature of the frame aids in easier installation. Snap the cover plate onto the frame until it is securely in place.
6. Restaurar energía: Once installation is complete and all components are securely fastened, restore power to the circuit from the main circuit breaker.
7. Funcionalidad de prueba: Test the switch/commutator to ensure it operates correctly.

6. Instrucciones de funcionamiento

The SIMON 10 Series switch/commutator is operated by pressing the rocker switch.

• As a Standard Switch: When wired as a single-pole switch, pressing the top or bottom of the rocker will toggle the connected light or device ON or OFF.
• As a Commutator (Two-Way Switch): When wired in a two-way configuration, pressing the rocker will alternate the circuit connection, allowing you to control a single light fixture from two separate locations. For example, one switch at the bottom of a staircase and another at the top.

7. Mantenimiento

The SIMON 10 Series switch/commutator requires minimal maintenance.

• Limpieza: To clean the surface of the switch, ensure power is disconnected at the circuit breaker. Use a soft, dry, or slightly damp Paño. No utilice limpiadores abrasivos, disolventes ni productos químicos fuertes, ya que pueden dañar el acabado.
• Inspección: Periodically inspect the switch for any signs of damage, loose connections, or discoloration. If any issues are observed, disconnect power and consult a qualified electrician.

8. Solución de problemas

If you encounter issues with your SIMON 10 Series switch/commutator, refer to the following common troubleshooting steps:

9. Garantía y soporte

For information regarding warranty coverage, technical support, or spare parts availability, please contact Simon customer service directly or visit the official Simon webSitio. Conserve su recibo de compra como comprobante de compra.

Simon Official Websitio: www.simon.es (Tenga en cuenta: URL es un example, verify the correct regional web(Sitio para soporte.)