HALO HLBSL6099FS351EMWR 6-inch Round LED Direct Mount Kit User Manual

1. Producto terminadoview

The HALO HLBSL6099FS351EMWR is a 6-inch white, round LED direct mount retrofit kit. This lighting fixture is designed for straightforward installation into drywall ceilings, specifically accommodating thicknesses between 1/2 inch and 1-1/4 inches, utilizing its integrated spring clips. It is suitable for direct contact with insulation, though its use with spray foam insulation is not recommended. The kit includes a remote control for convenient operation.

Figure 1: HALO HLBSL6099FS351EMWR 6-inch Round LED Direct Mount Kit. This image displays the white, round LED light fixture with its integrated spring clips visible on the side, indicating its design for direct ceiling mounting.

2. Información de seguridad

Lea y comprenda todas las instrucciones antes de comenzar la instalación. Si no las sigue, podría sufrir descargas eléctricas, incendios u otros peligros que podrían causar lesiones personales o daños materiales.

• Desconecte siempre la alimentación del disyuntor antes de realizar cualquier instalación o mantenimiento.
• Asegúrese de que todas las conexiones eléctricas cumplan con los códigos y ordenanzas locales, así como con el Código Eléctrico Nacional (NEC).
• Este producto debe ser instalado de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y el funcionamiento del producto y los peligros involucrados.
• Do not use with spray foam insulation.
• No modifique el accesorio de ninguna manera.
• Consulte a un electricista calificado si no está seguro acerca de alguna parte del proceso de instalación.

3. Contenido del paquete

Verifique que todos los componentes estén presentes antes de continuar con la instalación.

• HALO HLBSL6099FS351EMWR 6-inch Round LED Direct Mount Kit (Quantity: 4)
• Control Remoto (Cantidad: 1)
• Guía de instalación (Este manual)

4. Configuración e instalación

This LED kit is designed for direct installation into drywall ceilings. Ensure the power is OFF at the circuit breaker before starting.

1. Preparar la apertura: Cut a 6-inch diameter hole in the drywall ceiling at the desired installation location. Ensure the drywall thickness is between 1/2 inch and 1-1/4 inches.
2. Alambrado: Connect the fixture's wiring to the building's electrical supply wires. Follow standard electrical wiring practices:
   • Connect the black wire from the fixture to the black (hot) wire from the supply.
   • Connect the white wire from the fixture to the white (neutral) wire from the supply.
   • Connect the green or bare copper wire from the fixture to the green or bare copper (ground) wire from the supply.
   Secure all connections with appropriate wire connectors.
3. Monte el accesorio: Gently push the LED fixture into the prepared ceiling opening. The attached spring clips will automatically engage and secure the fixture to the drywall. Ensure the fixture is flush with the ceiling surface.
4. Restaurar energía: Una vez que el artefacto esté instalado de forma segura y se hayan realizado todas las conexiones, restablezca la energía en el disyuntor.

Nota importante: This fixture can come into direct contact with insulation. However, it is not recommended for use with spray foam insulation.

5. Instrucciones de funcionamiento

The HALO HLBSL6099FS351EMWR LED kit is operated via a wall switch or the included remote control.

5.1. Wall Switch Operation

Simply toggle the wall switch connected to the fixture to turn the light ON or OFF.

5.2. Operación de control remoto

The included remote control provides additional functionality. Refer to the remote control's specific instructions for pairing and advanced features, if applicable. Typical remote functions include:

• ENCENDIDO/APAGADO: Encender o apagar la luz.
• Atenuación: Ajuste el nivel de brillo.
• Ajuste de temperatura de color: Change the light's color temperature (e.g., warm white to cool white), if supported by the model.

Ensure the remote control has working batteries and is within range of the fixture for proper operation.

6. Mantenimiento

The HALO HLBSL6099FS351EMWR LED fixture requires minimal maintenance.

• Limpieza: Desconecte la alimentación antes de limpiar. Limpie el aparato con un paño suave.amp Paño. No utilice limpiadores abrasivos ni disolventes, ya que pueden dañar el acabado o los componentes eléctricos.
• Longevidad del LED: The integrated LED light source is designed for long life and does not require bulb replacement.

7. Solución de problemas

If you experience issues with your HALO LED fixture, refer to the following common troubleshooting steps:

If the problem persists after trying these steps, contact HALO customer support or a qualified electrician.

8. Especificaciones

9. Garantía y soporte

For warranty information and customer support, please refer to the official HALO Lighting webSitio web o contacte directamente con el servicio de atención al cliente. Conserve el recibo de compra para reclamaciones de garantía.

Manufacturer: Cooper Lighting LLC