1. Producto terminadoview
The Einhell TC-TC 800 Tile Cutter is designed for precise and efficient cutting of wall and floor tiles. This robust tool is suitable for various home renovation projects, offering clean cuts with minimal dust thanks to its water cooling system.
Características principales:
- Robust Stainless Steel Table: Measuring 395 x 385 mm, it is easy to clean and features an angular scale up to 45° with non-slip feet for stable operation.
- Precise Cutting Guide: Ensures exact and straight cuts. The angle stop is adjustable from -45° to +45° for miter cuts.
- Depósito de agua integrado: Provides necessary water cooling for the saw blade, protecting it from heat damage.
- Capacidad de corte: Maximum cutting height of 14 mm at 45° and 34 mm at 90°.
- Guardia de seguridad: A protective guard for the cutting disc ensures user safety from chips and dust.
2. Instrucciones de seguridad
Lea y comprenda siempre todas las advertencias de seguridad, instrucciones, ilustraciones y especificaciones que se incluyen con esta herramienta eléctrica. No seguir todas las instrucciones a continuación puede provocar descargas eléctricas, incendios o lesiones graves.
Advertencias generales de seguridad:
- Use equipo de protección personal (EPP) adecuado, que incluya gafas de seguridad, protección auditiva y guantes.
- Asegúrese de que el área de trabajo esté limpia, bien iluminada y libre de obstrucciones.
- Mantenga a los niños y transeúntes alejados mientras opera la herramienta.
- Never operate the tool if the power cord or plug is damaged.
- Desconecte siempre la fuente de alimentación antes de realizar cualquier ajuste, cambiar accesorios o realizar mantenimiento.
- Utilice la hoja correcta para el material que se va a cortar.
- Ensure the water reservoir is adequately filled before operation to prevent overheating of the blade.
3. Componentes sobreview
Familiarize yourself with the main components of your Einhell TC-TC 800 Tile Cutter:
- Cutting Table (Stainless Steel)
- Diamond Cutting Disc (180 mm diameter)
- Unidad de motor
- Depósito de agua
- Cutting Guide with Scale
- Angle Stop (-45° to +45°)
- Protector de la hoja
- Interruptor de encendido y apagado
- Asa de transporte
Figura 1: Sobreview of the Einhell TC-TC 800 Tile Cutter with its main parts.
4. Configuración
Before operating the tile cutter, ensure proper setup for safety and optimal performance.
4.1 Desembalaje e inspección
- Retire con cuidado todos los componentes del embalaje.
- Inspect the tool for any signs of damage during transit. Do not operate if damaged.
- Asegúrese de que todos los componentes enumerados estén presentes.
4.2 Llenado del depósito de agua
The integrated water reservoir is essential for cooling the diamond cutting disc and reducing dust.
- Locate the water reservoir beneath the cutting table.
- Fill the reservoir with clean water to the indicated level. Ensure the water pump is submerged.
- Compruebe periódicamente el nivel de agua durante el funcionamiento y rellénela según sea necesario.
Figure 2: Filling the water reservoir for wet cutting.
4.3 Adjusting the Cutting Guide and Angle Stop
For accurate cuts, adjust the cutting guide and angle stop as required.
- The cutting guide with scale ensures straight cuts. Position it according to your desired measurement.
- For miter cuts, adjust the angle stop between -45° and +45°. Secure it firmly before cutting.
Figure 3: Adjustable angle stop for miter cuts.
5. Instrucciones de funcionamiento
Follow these steps for safe and effective tile cutting.
5.1 Encendido / Apagado
- Connect the tile cutter to a suitable power outlet (240 Volts).
- Para encender, presione el botón verde “ON”.
- Para apagar, presione el botón rojo “OFF”.
Figure 4: Power switch for turning the machine on and off.
5.2 Hacer un corte
- Place the tile firmly on the stainless steel cutting table, aligning it with the cutting guide or angle stop as desired.
- Ensure the water pump is active and water is flowing to the blade.
- Turn on the tile cutter.
- Slowly and steadily push the tile through the rotating diamond blade. Avoid excessive force.
- Once the cut is complete, turn off the tile cutter and wait for the blade to stop before removing the tile.
Figure 5: Demonstrating a tile being cut with the machine.
5.3 Vídeo oficial del producto: Cómo utilizarlo
Video 1: This video demonstrates the basic operation and usage of a tile cutter, including setup and cutting techniques.
6. Mantenimiento
Regular maintenance ensures the longevity and performance of your tile cutter.
6.1 Limpieza del depósito de agua
After each use, clean the water reservoir to prevent buildup of tile dust and debris.
- Desconecte la fuente de alimentación.
- Remove the cutting table or access panel to reach the reservoir.
- Empty the dirty water and thoroughly clean the reservoir with fresh water.
- Vuelva a ensamblar los componentes.
6.2 Reemplazo de cuchilla
Replace the diamond cutting disc when it becomes dull or damaged.
- Asegúrese de que la herramienta esté desconectada.
- Use the provided tool to loosen the blade retaining nut.
- Carefully remove the old blade and install the new 180 mm diamond cutting disc, ensuring it is correctly oriented.
- Tighten the retaining nut securely.
7. Solución de problemas
This section addresses common issues you might encounter with your tile cutter.
| Problema | Posible causa | Solución |
|---|---|---|
| Poor cut quality (chipping, uneven edges) | Dull or incorrect blade; insufficient water cooling; pushing too fast. | Replace blade with a suitable diamond disc; ensure water reservoir is full and pump is working; reduce feeding speed. |
| Water overflow from table | Water channels blocked; reservoir too full; uneven surface. | Clean water channels; do not overfill reservoir; ensure the machine is on a level surface. |
| La máquina no arranca | Sin fuente de alimentación; interruptor defectuoso; problema con el motor. | Check power connection and circuit breaker; test the power outlet; contact customer support if switch or motor is faulty. |
| Rusted screws/components | Lack of proper drying/maintenance after wet use. | Regularly clean and dry all metal components after use. Apply a rust preventative lubricant (e.g., WD-40) to screws and moving parts. |
8. Especificaciones
| Característica | Detalle |
|---|---|
| Marca | Un infierno |
| Número de modelo | 4301185 |
| Fuerza | 800 vatios |
| Volumentage | 240 voltios |
| Velocidad | 2950 RPM |
| Diamond Cutting Disc Diameter | 180 milímetros |
| Altura máxima de corte (90°) | 34 milímetros |
| Altura máxima de corte (45°) | 14 milímetros |
| Angle of Cut | 45 grados |
| Table Dimensions (L x W) | 39.6 cm x 38.5 cm |
| Dimensiones del producto (L x An x Al) | 39.6 l. x 38.5 an. x 25.5 al. centímetros |
| Peso del producto | 9.1 kilogramos |
| Fuente de poder | Eléctrico con cable |
| Características especiales | Adjustable angle stop, parallel stop with scale |
9. Garantía y soporte
9.1 Información de garantía
This Einhell product comes with a Garantía limitada de 2 añosConserve su comprobante de compra para cualquier reclamo de garantía.
9.2 Atención al cliente
Para asistencia técnica, repuestos o consultas sobre la garantía, contacte con el servicio de atención al cliente de Einhell. Consulte el sitio web oficial de Einhell. websitio o el embalaje de su producto para obtener la información de contacto más actualizada.