Pixel TW-283 N3 Wireless Shutter Remote Control Timer User Manual

1. Introducción

The Pixel TW-283 N3 is a versatile wireless shutter remote control and timer designed for compatible Canon EOS cameras. It offers advanced functionality for various photography scenarios, including single shooting, continuous shooting, Bulb mode, delay shooting, and comprehensive timer schedule shooting. This manual will guide you through the setup, operation, and maintenance of your device to ensure optimal performance.

2. Contenido del paquete

• TW-283 Transmitter
• TW-283 Receiver
• Camera Connecting Cable (N3 type for Canon)
• Manual de usuario

3. Producto terminadoview

Familiarize yourself with the components of the Pixel TW-283 N3 system:

Figure 1: Transmitter (left) and Receiver (right) with key functions labeled.

Transmisor (TX)

1. Indicador de luz LED
2. Power Switch, Backlit Button
3. Number Add Button
4. Shift Left Button
5. Set/Confirm Button
6. Pantalla LCD
7. Timer Schedule Start/Stop Button
8. Number Reduce Button
9. Shift Right Button
10. Focus Button/Shutter Button

Receptor (RX)

1. Indicador de luz LED
2. Power Switch, Backlit Button
3. Pantalla LCD
4. Backlit/Channel Add Button

4. Configuración

4.1. Instalación de la batería

Both the transmitter and receiver require 2 AAA batteries each (not included). Ensure correct polarity when inserting batteries.

Figure 2: Correct battery insertion for Transmitter and Receiver.

4.2. Conexión a la cámara

The receiver connects to your camera via the provided N3 connecting cable. Attach the receiver to your camera's hot shoe and plug the cable into the camera's remote control port. The N3 cable is compatible with various Canon EOS models.

Figure 3: Interchangeable connecting cables, including N3 for Canon.

Figure 4: Wired connection setup for the remote control.

4.3. Pairing (Channel Setting)

To establish a wireless connection, ensure both the transmitter and receiver are powered on. The devices should automatically pair on the same channel (e.g., CH01). If pairing issues occur, manually set the channel on both units to match.

Figure 5: Wireless connection setup for the remote control.

5. Instrucciones de funcionamiento

5.1. Modos básicos de disparo

The TW-283 supports several shooting modes:

• Disparo único: Press the shutter button halfway to focus, then fully press to capture a single image.
• 1S Continuous Shooting: Captures a series of images at 1-second intervals.
• Disparos con bombilla: Allows for long exposures. Press the shutter button once to open the shutter, and again to close it.
• Disparo retardado: Set a delay time (1s to 59s) before the shutter is released.

Figura 6: Sobreview of the four main shooting modes.

Figure 7: Half-press for focus, full-press for shutter.

5.2. Timer Schedule Shooting

This advanced mode allows you to program a sequence of shots with specific delays, exposure times, intervals, and repeat cycles. Ideal for time-lapse photography or complex long-exposure sequences.

• Demora: Set the initial delay before the first shot.
• Largo: Set the exposure time for each shot (for Bulb mode).
• Intvl: Set the interval between shots.
• N1: Number of shots in the first group.
• Repetir: Set the interval for repeating the entire sequence.
• N2: Number of times to repeat the sequence.

Figure 8: Timer Schedule Shooting settings.

6. Mantenimiento

• Mantenga el dispositivo seco. No lo exponga al agua ni a la humedad.
• Evite impactos fuertes o caídas del dispositivo.
• Limpie con un paño suave y seco. No utilice productos químicos agresivos.
• Retire las baterías si el dispositivo no se utilizará durante un período prolongado.

7. Solución de problemas

7.1. El dispositivo no se enciende

• Compruebe si las pilas están insertadas correctamente con la polaridad correcta.
• Reemplace con baterías AAA nuevas.

7.2. No Shutter Response

• Asegúrese de que tanto el transmisor como el receptor estén encendidos.
• Verifique que el transmisor y el receptor estén configurados en el mismo canal.
• Check if the camera connecting cable is securely plugged into both the receiver and the camera's remote port.
• Confirm your camera is set to a compatible shooting mode (e.g., single shot, continuous, Bulb).
• Ensure the camera's remote control interface is correctly identified and used. For some Canon EOS models like 5D Mark IV or 6D Mark II, the interface might be next to the lens.

7.3. Image Blur During Long Exposure

• Ensure the camera is mounted on a stable tripod.
• Use the remote control to avoid camera shake from pressing the shutter button directly.

8. Especificaciones

9. Compatible Cameras (N3 Cable)

The Pixel TW-283 N3 is compatible with a wide range of Canon EOS cameras, including but not limited to:

• EOS R3, EOS R5, EOS R5 C
• 5DS, 5DS R, 5D, 6D, 7D
• 1D X, 1D X Mark II, 1DX Mark III
• EOS 1D, 1D C, 1Ds, 1DS Mark II, 1DS Mark III
• 1D Mark IV, 1D Mark III, 1D Mark II N, 1D Mark II
• 5D Mark II, 5D Mark III, 5D Mark IV
• 7D Mark II, 6D Mark II
• 50D, 40D, 30D, 20D, 10D
• D60, D30, D2000
• EOS 1V, EOS-3
• R5 Mark II

Note: Not compatible with Canon EOS R6.

Always check your camera's remote control interface before ordering. If unsure about compatibility, contact customer service.

10. Garantía y soporte

For warranty information or technical support, please refer to the official PIXEL webSitio web o contacte a su vendedor. Conserve el recibo de compra para reclamaciones de garantía.