Producto terminadoview
The Intermatic WP1000HC is a 1-gang, horizontal mount, non-metallic weatherproof cover designed for use with electrical outlets. This "while-in-use" cover provides protection for electrical connections even when a cord is plugged into the outlet, making it ideal for outdoor or damp locations. It is constructed from durable polycarbonate material and features a clear design, allowing for easy visual inspection of the outlet. The cover includes multiple insert types to accommodate various receptacle configurations, including duplex, Decora/GFCI, and combination toggle switch or single receptacles.
Key features include a 2-1/4 inch depth, a 0.5 inch cord diameter capacity, and a 0.78 inch exit port length. It also offers a padlockable option for added security.
Configuración e instalación
Before beginning installation, ensure power to the outlet is turned off at the circuit breaker to prevent electrical shock. This cover is designed for horizontal mounting over a single-gang electrical box.
- Prepare the Outlet Box: Ensure the existing electrical box is securely mounted and free from debris.
- Select the Correct Insert: The WP1000HC comes with three separate insert types:
- Receptáculo dúplex
- Decora/GFCI Receptacle
- Combination Toggle Switch or Single Receptacle (with diameters of 1.375", 1.625", or 1.75")
- Monte la placa posterior: Align the back plate of the weatherproof cover with the screw holes on your electrical box. Use the provided screws (or appropriate screws for your box) to securely fasten the back plate to the electrical box. Ensure it is flush and stable.
- Coloque la cubierta: Hinge the clear cover onto the back plate. Ensure the hinge pins are properly seated.
- Asegure la cubierta: Close the clear cover. It should snap securely into place. If using the padlockable option, insert a padlock (not included) through the designated holes for added security.
- Restaurar energía: Once the cover is fully installed and secured, you may restore power to the circuit breaker.
Figura 1: Varios views of the Intermatic WP1000HC Weatherproof While-In-Use Cover, illustrating its design and components. The image shows the clear front cover, the back plate with an insert, and a side profile.
Instrucciones de funcionamiento
The Intermatic WP1000HC cover is designed for simple operation.
- To Use the Outlet: Open the clear cover by unlatching it. Plug your electrical cord into the receptacle. The cover is designed to close over the cord while it is plugged in, providing continuous weather protection.
- To Close the Cover: Ensure the electrical cord (if present) is routed through the designated exit port at the bottom of the cover. Close the clear cover firmly until it latches securely. This ensures a weatherproof seal.
- Padlock Option: If desired, a padlock can be inserted through the holes on the cover to prevent unauthorized access or tampriendo
Mantenimiento
The Intermatic WP1000HC requires minimal maintenance to ensure its longevity and effectiveness.
- Limpieza: Limpie periódicamente la cubierta con publicidad.amp cloth to remove dirt, dust, or debris. Avoid using abrasive cleaners or solvents, as these may damage the polycarbonate material.
- Inspección: Regularly inspect the cover for any signs of damage, cracks, or wear, especially around the hinges and latch. Ensure the seal remains intact. If any damage is observed, replace the cover to maintain weatherproof integrity.
- Integridad del sello: Ensure the cover closes tightly and the seal around the edges is not compromised by debris or damage. A proper seal is crucial for weatherproof performance.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| La tapa no cierra de forma segura. | Obstruction, incorrect insert, or damaged latch/hinge. | Check for debris around the latch or hinges. Ensure the correct insert is used and properly seated. Inspect for physical damage; replace if necessary. |
| Agua dentro de la tapa. | Improper installation, damaged seal, or open cover. | Verify the cover is fully closed and latched. Inspect the seal for cracks or gaps. Re-install if necessary, ensuring a tight fit against the wall. |
| Difficulty plugging in cords. | Cord diameter exceeds capacity or improper alignment. | Ensure cord diameter is within the 0.5" limit. Verify the cord is routed correctly through the exit port. |
Presupuesto
- Modelo: WP1000HC
- Número de pieza: 078275028081
- Tipo: Weatherproof While-In-Use Cover
- Banda: 1 platos
- Montaje: Horizontal
- Material: Polycarbonate, Non-Metallic
- Color: Claro
- Profundidad del producto: 2-1/4 pulgadas
- Cord Diameter Capacity: 0.5 pulgadas
- Exit Port Length: 0.78 pulgadas
- Included Inserts: Duplex Receptacle, Decora/GFCI Receptacle, Combination Toggle Switch or Single Receptacle (1.375", 1.625", 1.75" diameters)
- Características: Padlockable Option
- Tipo de instalación: Atornillar
- Peso del artículo: 0.01 onzas
- Dimensiones del paquete: 2 x 2 x 2 pulgadas
Garantía y soporte
For detailed warranty information and technical support, please refer to the official Intermatic website or contact Intermatic customer service directly. Keep your purchase receipt for warranty claims.
Oficial de Intermatic Websitio: www.intermatic.com