Introducción
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Información de seguridad
- No exponga el escáner a temperaturas extremas, humedad o luz solar directa.
- Evite dejar caer el escáner o someterlo a impactos fuertes.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Mantenga limpia la ventana de escaneo para garantizar una lectura precisa del código de barras.
Contenido del paquete
Verifique que su paquete contenga los siguientes elementos:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Unidad de fuente de alimentación
- Documentation (this manual or similar)
Si falta algún artículo o está dañado, comuníquese con su proveedor de inmediato.
Configuración
1. Conexión del escáner
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Conectarse al escáner: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Conecte la fuente de alimentación: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Encendido inicial
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Operación del escáner
1. Escaneo de códigos de barras
- Apuntar: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Escanear: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Confirmación: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Comprensión de los indicadores
- LED verde: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Mantenimiento
Limpieza del escáner
- Limpie periódicamente la ventana de escaneo con un paño suave y sin pelusa.ampLimpiar con agua o un limpiador suave, no abrasivo.
- No utilice productos químicos agresivos, disolventes o materiales abrasivos, ya que pueden dañar la superficie del escáner.
- Asegúrese de que el escáner esté apagado antes de limpiarlo.
Almacenamiento
Cuando no esté en uso, guarde el escáner en un entorno limpio y seco, alejado de la luz solar directa y de temperaturas extremas.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| El escáner no se enciende. | Cable de alimentación no conectado; toma de corriente defectuosa; falla de la unidad de fuente de alimentación. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| El escáner no lee códigos de barras. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Presupuesto
- Modelo: SR30
- Número de pieza: 225-727-003 (Kit)
- Tipo de escáner: generador de imágenes lineal
- Interfaz: RS232
- Fabricante: Intermec
- Peso del artículo: 0.01 ounces (approximate, scanner only)
- Departamento: Código de barras
- ASIN: B003T0WF3S
Garantía y soporte
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webSitio. Conserve su recibo de compra como comprobante para reclamaciones de garantía.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.