Hold Fn+1/2/3 for 3-5 seconds till the indicators flash fast in blue, the keyboard is ready to pair.
Turn on your Bluetooth device and find “TH80 BT5.0″ or TH80 BT3.0”, then connect. When the keyboard is connected to the Bluetooth device, the light on the 1/2/3 key stops flashing and the connection is done.
Press Frn+1/2/3 to toggle between the Bluetooth devices 1/2/3.

PAIRING WIRELESS 2.4GHZ
Toggle the switch in the back to make sure that the keyboard is under the wireless mode:

Hold Fn+4 for for 3-5 seconds till the light flashes fast in green, the keyboard is ready to pair.
Insert the 2.4G dongle to your device, the 4 key stops flashing green and the connection is done.

WIRED MODE
Toggle the switch to the wired mode, press Fn+5 till the 5 key lights up in white, and the keyboard enters to the wired mode successfully.

CHECK BATTERY
Hold Fn+B, the keys from 1! to 0) lights up to show the battery percentage; for example, if the keys from 1! to 6° light up when holding Fn+B, it means that the battery life is currently 60%; if keys of 1-0) light up, battery life is 100%.

CHECK LAYER AND MODE
Hold Fn+Spacebar, the indicators of Z/X/C and 1/2/3/4/5 light up to show at which layer and which mode the keyboard is; for example, if the keys of X and 3 light up when holding Fn+Spacebar, it means that the keyboard is in layer 2 and under the wireless mode and connected to BT3 device.

SPECIFICATION

MODEL: EPOMAKER TH8O Pro
KEYS AMOUNT: 81 Keys
STRUCTURE: Gasket-like mount
STABILIZER TYPE: Plate-mounted
PCB TYPE: 3/5-pin Hotswap PCB
BATTERY CAPACITY: 3800mAh for keyboard, 3000mAh for Barebones kit
CONNECTIVITY: Type-C Wired, 2.4 & Bluetooth Wireless
ANTI-GHOST KEY: NKRO in all modes
POLLING RATE: 1000hz in Type-C Wired & 2.4G modes
COMPATIBILITY: WINDOWS/MAC
DIMENSION: 325 x 135 x 30 mm
WEIGHT: Around 0.9kg

REPLACING KEYCAPS AND SWITCHES

Remove Switches

Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

Check that all the switch metallic pins are perfectly straight and clean.
Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process. Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to: support@epomaker.com with your purchase order number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS

https://discord.gg/2q3Z7C2 Join our community and learn together with other keyboard enthusiasts

WARRANTY

EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear. If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker.
We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc.
We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

Made in China

Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road, Xili Street, Nanshan Disctrict, Shenzhen,Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

Documents / Resources

EPOMAKER TH80 PRO Mechanical Gaming Keyboard [pdf] User Manual
TH80 PRO Mechanical Gaming Keyboard, TH80 PRO, Mechanical Gaming Keyboard, Gaming Keyboard, Keyboard