EPOMAKER TH108 Hot Swappable Type C/Bluetooth/RGB Mechanical Keyboard User Guide

TH108 Hot Swappable Type C/Bluetooth/RGB Mechanical Keyboard

QUICK START GUIDE

EPOMAKER TH108

Full-size Hot-swappable Type-C/Bluetooth/2.4G RGB Mechanical Keyboard with Numpad

Should you require more assistance, please email us at support@epomaker.com.

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road,
Xili Street, Nanshan Disctrict, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

APEX CE SPECIALISTS GMBH
Habichtweg 1 41468 Neuss Germany
Contact: Wells Yan   E-mail: info@apex-ce.com

APEX CE SPECIALISTS LIMITED
89 Princess Street, Mancheste, M1 4HT, UK
Contact: Wells Yan   E-mail: info@apex-ce.com

222-259473

2BN64-LUMA84

WARNING

Choking Hazard Small Parts Keep away from children and pets

FUNCTION KEY COMBINATIONS

LINGHT CONTROL

FUNCTIONS KEYS FOR WINDOWS & MAC

FUNCTIONS KEYS FOR WINDOWS & MAC

WIRED CONNECTION

1. Toggle the connectivity switch to the USB side, make sure the keyboard is in the Wired mode.
2. Plug in the USB-C cable to the Type-C port.
3. When the backlight is on, the keyboard is connected.

PAIRING BLUETOOTH

1. Toggle the connectivity switch to the BT side, make sure the keyboard is in wireless mode.
2. Hold and press FN+Q/W/E until the light indicator flashes quickly, the keyboard is ready to pair.
3. Open up your Bluetooth device and find the name “Epo-maker TH108-1”, “Epomaker TH108-2”, or “Epomaker TH108-3” and connect.
4. When the light indicator stop flashing and back to current backlight effect, the keyboard is connected to your device.

Note:
Short press FN+Q/W/E to toggle among Bluetooth device 1/2/3.

CONNECT VIA 2.4G

1. Toggle the connectivity switch to the 2.4G side, make sure the keyboard is in wireless mode.
2. Short Press FN+R and the light indicator flashes quickly.
3. Insert the 2.4G receiver to your device.
4. When the light indicator stop flashing and back to current backlight effect, the keyboard is connected to your device.

Note: Hold FN+R until the light indicator flashes quickly, the keyboard is in the pairing mode.

LIGHT INDICATOR

1. Battery icon (upper-left corner) :
   a. Low battery: Red light blinks
   b. Charging: Red light remains on
   c. Fully Charged: Green light remains on
2.  Numpad: The indicator lights up (upper-left corner) when enabled.
3. Caps Key: The indicator lights up (upper-left corner) when enabled.
4. Scroll Key: The indicator lights up (upper-left corner) when enabled.

BATTERY CHECK

When the keyboard is in wireless connectivity, press and hold FN+Enter to check the keyboard battery. When holding FN+Enter, backlight will be off, keys from 1! to 0) lights up indicating current battery percentage. For example, if 1! to 6ˆ lights up, then the keyboard battery percentage is 60% ; if 1! to 0) lights up, then the keyboard battery percentage is 100%.

Note:

1. The keyboard charges under either Wired or Wireless connectivity with the device as long as the keyboard is plugged in.
2. Don’t use Charger to charge the keyboard.

SLEEP MODE

1. Wired Mode: Backlight stays on when the display is off (press any key to wake). Backlight turn off when the device sleeps.
2. Wireless Mode: Backlight turns off after 5 minutes of inactivity (press any key to wake). During device sleep, backlight turns off—press any key to reconnect (Q/W/E/R lights flash).

SPECS

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser:
https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboard-switches

Before installing switches, be sure the pins are clean and straight.

Push Straight Down

Please be gentle. Be sure the pins are aligned with the slots.

Included Tools

1. Keycap Puller
2. Switch Puller

1. Mechanical Switch
   Example of a switch as seen from top after you remove the keycap to prepare for switch removal.
2. Logo
3. Switch Shaft
4. The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.

Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.

We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any Official store of Epomaker, please contact them directly for any additional help.

Instagram               TikTok                     Facebook

Discord                 YouTube                               X

WARRANTY

EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear. If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker.

We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc.

We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

Documents / Resources

EPOMAKER TH108 Hot Swappable Type C/Bluetooth/RGB Mechanical Keyboard [pdf] User Guide TH108 Hot Swappable Type C Bluetooth RGB Mechanical Keyboard, TH108, Hot Swappable Type C Bluetooth RGB Mechanical Keyboard, Swappable Type C Bluetooth RGB Mechanical Keyboard, Type C Bluetooth RGB Mechanical Keyboard, Bluetooth RGB Mechanical Keyboard, RGB Mechanical Keyboard, Mechanical Keyboard, Keyboard

References

• User Manual