Categories: EPOMAKER

EPOMAKER 66ECS Wireless Keyboard User Manual

EPOMAKER 66ECS Wireless Keyboard

Keyborad Function Illustrate

Special keys Function table

Bluetooth Operation Instruction
Keyboard can be paired 3 Bluetooth devices, and the keyboard can be connected to different devices to achieve rapid connection by press the key. Keyboard reset and default to connect the last use of the device. If the keyboard is in the state of cable, you can switch to the Bluetooth state by FN+_-; then one more time to click FN+_-to back to the cable mode.

  1. Bluetooth indicator instruction:
    The indicator flash quickly, into pairing status. The indicator flashes slowly, into reconnecting status. The indicator is always on, int connected status .and after 5 seconds, the indicator is put out.
  2. Bluetooth pair instruction:
    Before into pairing,need to close the bluetooth of device that has paired to the keyboard. For example,After the completion of the Bluetooth 1 paired phone a, if you need to match the Bluetooth 2 and B cell phone, then need to first turn off the phone a Bluetooth, then FN+(9long by3S, Bluetooth indicator lights flash, open the phone B Bluetooth, Bluetooth keyboard selection, according to the prompts to enter pairing code and after pairing then open a phone’s Bluetooth. At this time through the FN+*8/(9 short press, the connection of mobile phone A/B switch. Similarly, if you need to Bluetooth 3 and mobile phone 3 pairing, you need to turn off the phone A, Bluetooth B mobile phone, until the completion of the pairing and then open.
  3. The following operation is error operation:
    The keyboard has been connected, FN+*8/(9/)0long press the matching operation, the keyboard does not respond to the operation; FN+*8/(9/)0short press the heavy even operation, if heavy even the equipment is not matched for the null device, the keyboard does not respond to the operation, the indicator light flash 2 under the return; (3) Connected devices have not been off, forced into the pairing operation, which is the keyboard will quickly connect to the paired devices, there will be 2 Bluetooth connection is the same device. At this time, please turn off the Bluetooth device, and then re pairing one of the bluetooth.
  4. Battery indicator:
    The battery indicator is below in the _-button. Always on for charging; Always off for charging completion; flash for low power.

USB,PS/2 Interface settings
Press “Left FN /Right FN + Backspace” for 5 seconds, indicator flash 1 times to USB, indicator flash 2 times to auto-identify for USB,PS/2.and restart the keyboard.The default settings is set to USB.

Bluetooth Sleep and Power down settings
Press “Left FN/Right FN + T” for 5 seconds, indicator flash 1-3 times are power downtime set to 1-3 hours.The default power down time is set to 1 hours.

Clear Key Counter
Press “Left FN+Right FN + Delete” for 5 seconds, the indicator flash,and the key counter will be clear .

Restore factory settings
Press “ESC + L-ctrl + Backspace+ Right” for 5 seconds will restore factory settings, restore factory settings will restart the keyboard.

Keyboard configuration

There are two modes for the keyboard, OFFICE mode and Custom mode. OFFICE mode is also Standard mode, as for Custom mode, you can make different
configurations to the keyboard, the details for how to configure and save under
custom mode are in below.

NOTE: Press the “Save” of main screen to save the configure when the configure be completed.

How to configure keyboard:

Under OFFICE mode, press the “M” key on the top right corner, “M” light turn on, then goes into custom mode. And goes into the OFFICE mode in the opposite way. All keys on the keyboard are divided into no FN layer,left FN layer and right FNlayer, Left/right FN layer can output only when combine with left/right FN. When finish the set up of all keys in programming software, to save and synchronize the configure with keys, single click the “WriteKeys” in the main screen. Single click the “Read configuration” in the main screen, it will read the standard configuration of OFFICE mode when under the OFFICE mode and read custom configuration under custom mode. When the “M” light is on, the keyboard is under custom mode, all the custom functions can be used.

single key/ combine keys
  1. Single click on the key you need to configure, click “Uni/ combo” in the “KeySettings” surface.
  2. Choose “Single” or “Combo”, single click “Record” to record the keys, combine keys can record six at most.
  3. single click “OK”
Macro definition

The keyboard can be defined in the overall definition under a custom mode shows astrong programmable feature.

What is Macro
Macro is the whole series actions that you can specify order to the keyboard. Accurately speaking, it’s a series key press and key release, record every single timeof the key’s press, release and delay. Among which, it can automatic input when delay, that is all the time between press and release can automatically input.

How to define a macro?

  1. Choose the key you need to configure, click “macro ”;
  2. Choose “New” on the left side of the appear window;
  3. Choose a new macro, selected the style of output and automatic delay in the macro edit on the right side, then click “Record”, type the keys that need to be define on the keyboard and click “Stop Rec”;
  4. Single click “OK”.

How to set up delay
Delay is the time between the press and the release of keys.keyboard has the automatic delay record and can modify delay time: Set up automatic delay record: drive automatic records the time that typing actions need; Modify delay time(50ms-60000ms, 1000ms=1s): after define a macro, single clickthe delay time two keys already have, then the delay time will become to be editableand edit the delay time .sigle click the other area of record list to exit the editable status.

How to insert mouse and delay
After recording a macro, right click the key in the edit list, choose operate insert mouse and delay.

Simulate keystroke

What is simulated keystroke?
Simulate keystroke is the function that after you click the simulate key, the
keyboard will simulate the keystroke in a fast speed, it ends when the key bounce, it can also set up the speed of keystroke.

How to set up a simulate key stroke?

  1. Single click the key you need to configure,click “keystroke” in the “keys set up panel”;
  2. Choose “New” in the left side of the appeared window;
  3. Choose a new-built keystroke, set up the keystroke time in the edit list onthe right side, single click “Record”, type in the keys that need define, thenclick “Stop Rec”, simulate keystroke can record six at most;
  4. Single click “OK”.
Multi-Media

The keyboard support usual function for multi-media, custom multi-media simplify the layout of keyboard.

  1. Single click the key you need to configure, single click “Multimedia”;
  2. Choose custom multi-media in the multi-media interface, then click “OK”
Mouse

The keyboard support Mouse.Unit Time refers to the time required by a mouse cursor move to a cell; Unit Pixel refers to the number of pixels that move a cell inthe mouse cursor;First Delay refers to the interval between the mouse cursor moving the first cell to the second cell.

  1. Single click the key you need to configure, click “Mouse” in the dialog box of “Key Settings” that pops out;
  2. Choose custom mouse functions in the mouse panel, the click “OK”.
Function Key

The control key are divide into key function and backlight function.

  1. Single click the key you need to configure, click “Funcion” in the dialog boxof “key Settings” that pops out;
  2. Choose custom functions in the control key panel, the click “OK”.
Power

The keyboard support power function.

  1. Single click the key you need to configure, click “power” in the dialog box of “ KeySettings” that pops out;
  2. Choose custom functions in the power panel, the click “OK”

Empty configuration
There are two circumstances for empty configuration, one is empty single key configuration, the other is empty all the configured keys. To empty single key configuration, just single click the key and choose “Clear” inthe set window. To empty all the configurations, single click “Clear” in the function bar on the main screen.

How to save and open configuration

Every configuration document corresponds to a kind of keystroke mode, so it will
be more convenient for the users to configure the common programs of the keyboard. Configuration information include keys set up information and backlight set up information. You can save those configurations that don’t need in a short time on your PCanddirect import next time when needed. This can avoid set up repeated. You can still import the documents saved in PC when using another computer, The specific ways are below:

Open the configuration

  1. Single click “open” at the function bar in main screen, choose the catalog and the corresponding configuration in the dialog box of open configuration that pops out.
  2. Single click “Open”.

Save configuration

  1. Single click “Save” at the function bar in main screen, choose the catalog and type in the name of the configuration in the dialog box of save configuration that pops
    out.
  2. Single click “Save”.

How to Get key usage times
Single click “Get Counter” at the function bar in main screen, after reading the completion, the mouse moves to the corresponding button position, the information box can see the number of times the button is hit.

How to upgrade keyboard firmware

Upgrade keyboard firmware in order to improve the performance of the keyboard and the function that is designed for users’ experiences.

  1. Single click “Get Version” and can get the firmware‘s name and version.
  2. Single click “Open”, choose .bin document and single click “Update”, then updated the firmware of the keyboard with the tips.

Documents / Resources

EPOMAKER 66ECS Wireless Keyboard [pdf] User Manual
66ECS, Wireless Keyboard, 66ECS Wireless Keyboard, Keyboard

References

    Share

    Recent Posts

    VALBERG WF 1214 B W566C Washing Machine User Guide

    WF 1214 B W566C Washing Machine ELECTRO DEPOT 1 route de Vendeville 59155 FACHES-THUMESNIL -…

    40 seconds ago

    QUOIZEL LSB1716OZ Lisbon 3 Light 17 inch Old Bronze Semi-Flush Mount Ceiling Light Installation Guide

    LSB1716OZ Lisbon 3 Light 17 inch Old Bronze Semi-Flush Mount Ceiling Light INSTALLATION GUIDE FOR…

    44 seconds ago

    HERSCHEL Vulcan Fan Purge Timer Instruction Manual

    Vulcan Fan Purge Timer HERSCHEL Infrared Fan Purge Timer INSTALLATION & OPERATING INSTRUCTIONS ELECTRICAL EQUIPMENT:…

    48 seconds ago

    PeakTech 1080 Digital Pen Type Multimeter Instruction Manual

    1080 Digital Pen Type Multimeter PeakTech® 1080 Bedienungsanleitung / Operation manual Digital Pen-Type-Multimeter 1. Sicherheitshinweise…

    1 min ago

    BLUSTREAM IP50HD-RX High Definition Video Over IP Receiver User Manual

    IP50HD-RX High Definition Video Over IP Receiver IP50HD-RX High Definition Video Over IP Receiver Description…

    1 min ago

    fri-jado Custom Counter Hot Full Serve or Self-Serve Instruction Manual

    Custom Counter Hot Full Serve or Self-Serve Service Parts List Custom Counter Hot and Cold…

    2 mins ago