EOMNIA EH.866 Series Handle Sets
Product Specifications
EH.8668 (A)
- Front plate
- Back plate
- Lock Cylinder
- Password keyboard swiping area
- Electronic module master control Thumbpiece
- Initialize button
- Turnpiece
- Battery compartment
- Knob
- Grip Handle
- Battery cover
Product Usage Instructions
EH.8668 Installation Guide
Install Exploded View
- [Exploded view diagram here]
Installation Steps
- Step 1: Gather the components listed in the installation manual.
- Step 2: Attach the front plate and back plate to the door using the provided screws.
- Step 3: Insert the lock cylinder and secure it in place.
- Step 4: Install the password keyboard swiping area and the electronic module master control.
- Step 5: Mount the thumbpiece, knob, grip handle, and battery cover.
- Step 6: Complete the installation by testing the functionality of the lock.
Notice
Please read and understand all instructions before use:
- The warranty does not apply if damage is caused by failure to follow these instructions.
- Only alkaline batteries can be used, other batteries are not recommended.
- When cleaning the product, please wipe it with a soft cloth.
- When the battery power is low and the alarm occurs, please replace the battery in time to keep the battery power sufficient.
The “electronic main control module” of this product (please refer to the basic product introduction) is dust-proof and water-resistant; tested under controlled laboratory conditions, its effect reaches IP65 level; dustproof and water-resistant functions are not permanently effective.
- Protective properties degrade due to daily wear and tear. Do not charge the smart lock (emergency power interface) when it is wet; damage caused by liquid entering the internal structure of the electronic lock is not covered by the warranty.
Read before use
Product specifications
EH.8668 (A)
EH.8668 (B)
Read before use
Product specifications
EH.8669 (A)
EH.8669 (B)
EH.8688 (A)
EH.8688 (B)
23/8” 23/ 4” adjustable deadbolt
Adjustment instruction of deadbolt. When adjusting, rotate the “deadbolt” (as the picture).
- Can be adjusted to two backsets 23 /8” and 23 ./4” (as above picture).
- After selecting the backset, return to the correct position of the deadbolt.
23/8” 23/4” adjustable latch
Adjustment instructions of latch
- Can be adjusted to two installation center distances: 23/8” and 23/4”.
- When adjusting, push the “adjustable square core” forward to 23 /8” (Picture 1), and pull it backward to adjust to (Picture 2).23/4”
Installation instructions (EH.8668 (A) is a reference example)
Install exploded view
Installation steps
- Make holes in door “A” and “B” at 2-1/8″, and for the Grip Handl e bottom screw (per template).
Notice
For details, please refer to the <User manual>
Notice
For battery installation details, please refer to the <User manual>
Notice
- Please do not try to disassemble this product by yourself; otherwise, you may get an electric shock or damage the product.
- Do not use hard or heavy objects to knock this product.
- When going out, please make sure the lock is locked before leaving.
- Please be careful not to hit the handle to avoid injury.
- Do not use any corrosive cleaners to clean this product, such as gasoline, products that contain alcohol, or other chemicals, etc., otherwise it will cause damage to the electronic circuit, product degradation, or paint peeling.
- Please change your password regularly (about three months); when your password is leaked, please change your password in time; our company is not responsible for accidents caused by user negligence.
- When using manual mode to lock, please be sure to confirm whether the door is closed and locked.
- Do not use rechargeable batteries; only alkaline batteries are recommended.
- Please be sure to follow the above instructions to avoid any injury or property damage.
- The performance of this product cannot be guaranteed in special environments such as high-humidity weather and the seaside.
FAQs
Q: How do I adjust the deadbolt?
A: To adjust the deadbolt, rotate it as shown in the adjustment instructions. Ensure it is set to the desired backset measurement (23/8 or 23/4) and return it to the correct position.
Q: How do I adjust the latch?
A: The latch can be adjusted by moving the adjustable square hub to the appropriate installation center distance (23/8 or 23/4). Follow the provided pictures for guidance on adjusting the latch.
Documents / Resources
 | EOMNIA EH.866 Series Handle Sets [pdf] Installation Guide EH.8668, EH.8669, EH.8688, EH.866 Series Handle Sets, EH.866 Series, Handle Sets, Sets |