Ruijie RG-RAP2260H Sendrata Alirpunkto Uzanta Manlibro

Ruijie RG-RAP2260H Wireless Access Point

Pako Enhavo

objekton	Kvanto
RG-RAP2260(H) Access Point	1
Muntanta Krampo	1
Phillips-Ŝraŭbo	4
Murankro	4
uzanto Manlibro	1
Atestilo de Kvalito	1

Aparataro

supro View

malsupro View

Noto: RESET Hole LAN1/2.5G/PoE Port LAN2/2.5G Pot 48 V DC input plug

PoE power supply: Connect one end of the Ethernet cable to the LAN1/2.5G/PoE port of the access point, and the other end to a PoE-capable switch or other power source equipment (PSE).
DC power supply: Connect the DC power adapter (48 V/1A) to the DC input plug on the access point.

Teknikaj Specifoj

objekton	specifo
Dimensions (W x D x H)	230 mm x 230 mm x 48mm (9.06 inch x 9.06 inch x 1.89 inch, without the mounting bracket)
Datumoj Imposto	2.4 GHz: up to 1148 Mbps 5 GHz: up to 4804 Mbps Kombinita: 5952 Mbps
Funkcianta Radio	802.11 b/g/n/ax: 2.4 GHz to 2.4835 GHz 802.11 a/n/ac/ax: 5.150 GHz to 5.350 GHz, 5.470 GHz to 5.850 GHz
anteno	Enkonstruita omnidirekta anteno
Servaj Havenoj	Two 10/100/1000/2500 Mbps self-adaptive Ethernet ports
Rekomenci/Restarigi	apogita
LED-stato	apogita
Potenca Provizo	Estas tri elektraj reĝimoj disponeblaj: •       Standard PoE: IEEE 802.3bt standard, backward compatible with the IEEE 802.3at standard •       60 W Passive PoE adapter (Optional accessory) •       Local power supply: 48 V DC /1 A Note: The access point is not 802.3af-compliant. (See Appendix for power supply modes and respective data imposto.)
Max Potenco konsumo	40W
medio	Funkciiga temperaturo: 0 ° C ĝis 40 ° C (32 ° F ĝis 104 ° F)
	Stokada temperaturo: -40 ° C ĝis 70 ° C (-40 ° F ĝis 158 ° F)
	Funkcia humideco: 5% ĝis 95% (nekondensa)
	Stoka humideco: 5% ĝis 95% (nekondensa)
Pezo	1.8 kg (3.97 lbs, without the mounting bracket)
Koloro	Varma blanka

LED kaj Restarigi Truon

LED	Statuso	Priskribo
	Solida bluo	The access point is functioning properly with no alarms.
	off	La alirpunkto ne ricevas potencon.
	Malrapide palpebrumi	The access point is functioning properly but there is an alarm generated.
	Rapida palpebrumado	Eblaj kazoj: 1. Restarigi la alirpunkton al fabrikaj agordoj. 2. Ĝisdatigi la firmware. 3. Pritraktado de alarmoj aŭtomate. 4.  Starting up the access point.

Restarigi Truon	Premu kaj tenu la pinglon al la Restarigi truon dum malpli ol 2 sekundoj.	Rekomencu la alirpunkton.
	Press and hold the pin to the Reset hole for more than 5 seconds.	Restarigu la alirpunkton al fabrikaj agordoj.

Tools (Customer-supplied)

Mounting the Access Point without Security Lock

To mount the AP with the security lock, see Mounting the Access Point with Security Lock.

1. Drill four holes at 53 mm (2.09 in) spacing on the wall or ceiling.
2. Take out the mounting bracket from the packaging material.
3. Secure the mounting bracket on the ceiling or wall by using screws.
4. Connect the Ethernet cable to the LAN port on the rear of the AP.
5. Vicigu la kvadratajn piedojn sur la malantaŭo de la AP super la muntaj truoj sur la krampo. Glitu la AP en la truojn ĝis ĝi klakas al loko.

Mounting the Access Point with Security Lock (Optional)

Loosen the security screw to engage the security lock.

Align the square feet on the rear of the AP over the mounting holes on the bracket. Slide the AP into the mounting holes.

singardemo:
Slide the AP into the mounting holes in the opposite orientation of the arrow (UP) indicated on the bracket until it clicks into place. Do not forcibly slide the Pinto the mounting holes on the brackets. After installation, verify that the AP is properly secured on the bracket.

Forigante la Alirpunkton

1. If the security lock is used, keep the top of the key against the edge of the mounting bracket (with the Ruijie logo on the key pointed upwards). Slide the key along with the four edges of the mounting bracket.
2. Attempt to insert the key into the keyhole. It can only be inserted into one marked keyhole.

Removing the Wall-Mount AP

Hold the AP in your hands and push it upward and away from the bracket. Removing the Ceiling-Mount AP

Hold the AP in your hands and attempt to push it away from the bracket in each orientation.
The AP can only be pushed out in one of the four orientations.

Agordi la Alirpunkton

Metodo 1 (Rekomendita)
Scan the QR-code in the manual or on the device to download Ruijie Cloud App. Find First time use Ruijie Cloud? Follow the guide on the App to configure the network.

metodo 2

1. Konektu la alirpunkton al la SSID. Se pluraj aparatoj ekzistas en la reto, uzu SSID @Ruijie-mXXXX. Se nur unu aparato ekzistas en la reto, uzu SSID @Ruijie-sXXXX. Vi ankaŭ povas krei kablian konekton konektante vian komputilon al la Ethernet-haveno de la alirpunkto per Ethernet-kablo.
2. If there is only one Reyee device in the network, access http:/1192.168.120.1 via the browser. Otherwise, access http:/110.44.77.253.
   In the latter case, configure your phone or PC with an IP address in the same network segment as 10.44.77.253, for example, 10.44.77.250.
3. Alklaku Komencu Agordon por krei retajn projektojn.

apendico

potenco Importa	Loka elektroprovizo: 48 V DC/1 A
	Norma PoE: IEEE 802.3bt normo, malantaŭen kongrua kun la IEEE 802.3at normo
Elektra Proviza Reĝimo	2.4 GHz	5 GHz	Datumoj Imposto	Maksimume Potenco konsumo
IEEE 802.3bt Standard (Recommended)	4 × 4	4 × 4	5952 Mbps	40W
60 W Passive PoE Adapter (Optional Accessory)	4 × 4	4 × 4	5952 Mbps	40W
Local Power Supply (48 V DC /1 A)	4 × 4	4 × 4	5952 Mbps	40W
IEEE 802.3at normo	2 × 2	2 × 2	2976 Mbps	25W
Note: The access point is not 802.3af-compliant.

Dokumentoj/Rimedoj

Ruijie RG-RAP2260H Wireless Access Point [pdf] Uzanta Manlibro RG-RAP2260H, Wireless Access Point, RG-RAP2260H Wireless Access Point, Access Point