Carlson® 41” Extra Tall Walk-Thru Pet Gate

Introduction

Welcome to your new Carlson® 41” Extra Tall Walk-Thru Pet Gate. This gate is designed to provide a safe and convenient barrier for your pets, while allowing easy passage for adults. Please read this manual thoroughly before assembly and installation to ensure proper and safe use.

Important Safety Information

❗ WARNING: Failure to follow these instructions could result in serious injury or death.

• This gate is intended for use with children and pets.
• Always ensure the gate is securely installed before use.
• Do not use the gate if any parts are missing or damaged.
• Never use the gate without all hardware properly installed.
• This gate is not a substitute for adult supervision.
• Keep small parts away from children during assembly.
• Ensure the gate is installed on a stable, level surface.
• Do not install the gate near heat sources or in areas where it could be a tripping hazard.
• Maximum opening width: [Specify width if known, otherwise use placeholder].
• Maximum height of pet: [Specify height if known, otherwise use placeholder].

Parts List

Please check that you have all the parts listed below before beginning installation. If any parts are missing or damaged, please contact Carlson customer support.

A. Gate Panel

1x - The main gate structure with the walk-through door.

B. Extension Kit (Optional)

1x - If included, used to widen the gate opening.

C. Top Mounting Bracket

2x - Brackets that attach to the wall or doorframe.

D. Bottom Mounting Bracket

2x - Brackets that attach to the wall or doorframe.

E. Pressure Bolts

4x - Bolts that thread into the mounting brackets to secure the gate.

F. Rubber Sleeves

4x - To protect walls from pressure bolts.

G. Wall Cups

4x - To provide a stable surface for pressure bolts.

H. Spanner Tool

1x - For tightening pressure bolts.

I. Lock Nuts

4x - Used with pressure bolts for added security.

J. Small Pet Door

1x - Integrated door within the main gate for smaller pets.

[Diagram Description: An illustration showing all parts labeled A through J, laid out clearly.]

Installation Instructions

This gate is designed for pressure-mount installation. No tools are required for basic installation, but the included spanner tool is recommended for optimal tightening.

1. Prepare the Opening: Ensure the desired opening is clear and the surfaces where the gate will be mounted are clean and flat.
2. Attach Mounting Brackets:
   1. Place the top mounting brackets (C) on the wall or doorframe at the desired height, ensuring they are level.
   2. Place the bottom mounting brackets (D) on the wall or doorframe, aligning them with the top brackets.
   3. [Diagram Description: Illustration showing placement of top and bottom mounting brackets on a wall frame.]
3. Install Pressure Bolts:
   1. Insert rubber sleeves (F) onto the ends of the pressure bolts (E).
   2. Thread the pressure bolts (E) into the mounting brackets (C and D).
   3. Place wall cups (G) over the ends of the pressure bolts (E) that will press against the wall.
   4. [Diagram Description: Close-up view of a pressure bolt with rubber sleeve and wall cup being inserted into a bracket.]
4. Mount the Gate:
   1. Position the gate panel (A) between the mounting points.
   2. Align the gate with the pressure bolts (E).
   3. Thread the pressure bolts (E) into the gate's frame until snug.
   4. [Diagram Description: Image showing the gate panel being positioned and aligned with the wall-mounted hardware.]
5. Secure the Gate:
   1. Using the spanner tool (H), tighten the pressure bolts (E) evenly on both sides. Ensure the gate is vertical and secure.
   2. Install lock nuts (I) onto the pressure bolts (E) for added security.
   3. Check that the gate is stable and does not wobble. The walk-through door should open and close smoothly.
   4. [Diagram Description: Illustration demonstrating the use of the spanner tool to tighten pressure bolts and the addition of lock nuts.]
6. Adjust Tension: Periodically check and adjust the tension of the pressure bolts as needed to maintain stability.

Note on Extensions: If using an extension kit (B), follow the specific instructions provided with the kit to attach it to the gate panel before installation.

Usage Instructions

Opening and Closing the Main Gate

To open the gate, lift the handle on the walk-through door and swing it open. To close, swing the door back until it latches securely. Ensure the latch engages properly.

[Diagram Description: Illustration showing the handle mechanism and the gate door swinging open and closed.]

Using the Small Pet Door

The integrated small pet door (J) allows smaller pets to pass through while keeping larger pets or children contained. To open the small pet door, slide or lift the latch mechanism as indicated on the door itself. Ensure it is securely closed when not in use.

[Diagram Description: Close-up of the small pet door with an arrow indicating how to open/close it.]

Walk-Through Feature

The walk-through design allows adults to pass through the gate without needing to remove it. Simply open the main door.

Care and Maintenance

• Cleaning: Clean the gate with a soft, damp cloth. Mild soap can be used if necessary. Do not use abrasive cleaners or solvents, as they may damage the finish.
• Inspection: Regularly inspect all parts for wear and tear, and ensure all hardware remains tight.
• Re-tensioning: If the gate becomes loose, re-tighten the pressure bolts using the spanner tool.

Support and Warranty

For questions regarding installation, parts, or warranty information, please refer to the Carlson® website or contact their customer service department. Product support is available to ensure you get the most out of your gate.

[External Link Placeholder: Carlson® Official Website]