User Manual for UNIPULSE models including: 127E02A0 RF Module, 127E02A0, RF Module, Module
UNIPULSE Corporation 127E02A0 F3O-127E02A0 F3O127E02A0 127e02a0
Reference: Specifications 1.Product name: RF Module 2.Model name:127E02A0 3.Frequency range:920.7MHz924.5MHz 4.RF Maximum output power: below 20mW 5.Antenna impedance: 50 6.Modulation method: FSK 7.Rated power supply:DC3V±10% 8.Module size:35.3x22.7mm 9.Operating temperature range: -1050 Trade Mark: Description of Pin Pin Signal 1 IO1 3 IO2 5 IO3 7 IO4 9 IO5 11 IO6 13 IO7 15 IO8 17 IO9 19 IO10 21 IO11 23 IO12 25 IO13 27 IO14 29 IO15 31 IO16 33 IO17 35 IO18 Pin Signal 2 D_GND 4 D_GND 6 D_GND 8 D_GND 10 D_GND 12 D_GND 14 D_GND 16 D_GND 18 D_GND 20 D_GND 22 VCC 24 VCC 26 VCC 28 VCC 30 VCC 32 VCC 34 VCC 36 VCC 37 IO19 39 IO20 Location of Pin 38 VCC 40 VCC The 127E02A0 module is designed to comply with the FCC statement. FCC ID is F30127E02A0 The host system using 127E02A0 should have label indicated it contain modular's FCC ID : F3O-127E02A0. This radio module must not be installed to co-locate and operating simultaneously with other radios in host system, additional testing and equipment authorization should be required to operating simultaneously with other radio. List of applicable FCC rules: The module complies with FCC Part 15.247. Summarize the specific operational use conditions: The module has been certified for Fix, Mobile applications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Module procedures: The module has RF shielding. which belong to signal module Standard requires: Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device (see Comprehensive integration instructions below). Installation Notes: 1) 127E02A0 Module Power supply range is DC 2.7V~3.3V, when you use 127E02A0 Module design product, the power supply cannot exceed this range. 2) Make sure the module pins correctly installed. 3) Make sure that the module does not allow users to replace or demolition 4) Any modifications to the module model 127E02A0 may invalidate regulatory approvals or may necessitate notifications to the relevant regulatory authorities. 5) OEM must inform UNIPULSE Corporation Compliance of any changes which may require the Class I or Class II permissive changes for the FCC. Antennas: The module has Helical antenna and Monopole antenna. Information on test modes and additional testing requirements: When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host manufacturer may operate their product during the measurements. In setting up the configurations, if the pairing and call box options for testing does not work, then the host product manufacturer should coordinate with the module manufacturer for access to test mode software. Additional testing, Part 15 Subpart B disclaimer: The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity. Information on test modes and additional testing requirements: When testing host product, the host manufacture should follow FCC KDB Publication 996369 D04 Module Integration Guide for testing the host products. The host manufacturer may operate their product during the measurements. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statements 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.Microsoft Word 适用于 Microsoft 365