User Manual for The Home Depot models including: 30043 Ceiling Fan With Light, 30043, Ceiling Fan With Light, Light
15 часов назад — Take out fan downrod. - Remove cotter pin and bolt from downrod. - Take out fan motor housng. - Loosen jam screw in yoke until it is flush with the inside ...
CEILING FAN WITH LIGHT ITEM #30043 support@ceilingfanhelp.com Installation Instructions 5-9 Operation 10 Troubleshooting Guide 11 Balancing Kit 12 All wiring must be in accordance with the National 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 70 lbs (31.8 kg). Use only UL Listed outlet boxes marked " Acceptable for Fan Support of 70Ibs. (31.8 kg) or less. " 4. Ensure that the installation site allows clearance for rotating fan blades, keeping them at least 7 feet above the floor. 5. Do not place objects in the path of the blades. 6. To clean the fixture ,turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth. 7. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. 8. All screws must be checked and re-tightened before installation. To reduce the risk of fire or injury, do not use this product with any variable (rheostat) wall control. objects. To reduce the risk of electrical shock, you'd better not install the fan with an isolating wall control / switch. 2 6.5 in 2.3in 12.4 in 15.6 in S1 S2 S3 S4 OFF ON/O FF F R 3 2 4 SETU P 1 STOP 5 6 1H 4H 8H 2 3 4 5 60 in S5 Hardware Package S1.Machine Screw S2.Washer S6 S3.Wood Screw S4.Wire Nut S5.Blade Screw S6.Balance Kit 6 7 8 9 10 Item name 1.Remote Control 2.Hanger 3.Canopy 4.Canopy Cover 5.Yoke Cover 6.Dwonrod 7.Long Dwonrod 8.Motor Housing 9.Lamp Housing 10.Lamp Shade 11.Blade 3 Quantity 2 4 4 3 1 1 1 1 1 1 1 1 1 1 1 1 3 Receiver Bolt jam Screws Blade Blade Screw Blade Screw Lamp shade Hanger Canopy screw Hanger Ball Canopy Canopy Cover Yoke Cover Cotter Pin Motor Housing Lamp Housing (LED inside) Lamp housing screw 4 Step1 REMOVE THE SHIPPING BLOCKS -Remove the shipping blocks from the motor. Save the blade screws. They will be needed for blade installation. GUARDE DESCARTAR Step2 MOUNTING - Take out fan downrod. - Remove cotter pin and bolt from downrod. - Take out fan motor housng. - Loosen jam screw in yoke until it is flush with the inside surface. - Place the downrod inside the canopy, canopy cover, and yoke cover. - Route wires exiting motor through yoke cover, canopy and downrod. Fig.2a Cotter Pin Fig.2b Downrod Jam Screw Bolt Yoke Fig.2c Fig.1 Downrod Canopy Canopy Cover Yoke Cover 5 Step2 MOUNTING(CONTINUED) - Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires. - Tighten bolt. Secure with cotter pin through hole in the end of the bolt. - Secure downrod in position by tightening jam screws. - Slide yoke cover down and it will flush with the motor housing. Fig.2d Yoke Cover Bolt Downrod Canopy Canopy Cover Cotter Pin Yoke Step3 INSTALL HANGER Fig.2e Jam Screw Jam Screw - Secure hanger to metal outlet box. - The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss. Fig.3a Fig.3b Fig.3c Washer Outlet Box Hanger Outlet Box Screw not provided hanger boss hanger ball groove Outlet Box Canopy Canopy cover Yoke cover Motor housing 6 Step4 Attaching the Fan Blades. - Attach the blade to the motor with blade screws. - Repeat this step for each blade assembly. Fig.4 Blade Blade screw Step5 Assembling the lamp housing - Feed the wire through the center hole of the lamp housing. - Secure the lamp housing with screws. - Connect the motor end plug to the light source end socket. Fig.5 7 Step6 The lampshade installation - Install the lampshade to the lamp housing by turning clockwise to lock it into place. Fig.6 1 2 Step7 The receiver installation - Place the receiver in the hanger. Fig.7a Fig.7b 8 Step8 Wiring the Fan - Wiring according to the wiring diagram. From ceiling white black white black white blue white blue From fan Fig.8a grounding wires (From ceiling) grounding wires (From fan) and connectors Step9 Attaching the Canopy and Canopy cover - Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely. - Move the canopy cover onto the canopy. (The decorative cover is magnetically attached.) Fig.9a Fig.9b Fig.9c hanger screw Canopy Canopy cover 9 Operating FUNCTION INSTRUCTION OF EMITTER - Open the battery cover on the hand-held remote and install a pair of AAA batteries (1.5V) into the emitter. Batteries are not included." - pair the remote before use: -Turn on the power switch and press the button ( 2 + ) within 3 seconds. The receiver will emit two 'tick' sounds, indicating successful pairing. If pairing is not successful, turn off the power for one minute, then repeat the process." -If the emitter cannot control the receiver, check if the battery is properly installed, with the correct polarity, and whether the battery is full or empty. - If the emitter cannot control the receiver, check if there are any similar remote-controlled products nearby, and ensure they are not interfering, as products using the same frequency can disturb each other. -Please remove the battery from the emitter if it will be unused for a long period. - When installing the fan, do not press the antenna (or other wires) against the fan ceiling cover, as this may damage the wires and cause a short circuit. 1 All off 2 Fan forward rotating 3 Natural wind 4 Speed control 5 Fan off 1 6 Timer 2 7 Light on/off switch (Color temperature can be selected) 3 8 Fan reversal rotating 4 9 Turn OFF the beeping 5 After powering on, press and hold " " on the handle immediately. After hearing the beep, release the " " button to turn off the beeping. (If you need to turn the 6 prompt sound back on, turn off the power first, then turn it on again, and repeat the above actions) OFF ON/OFF 7 F R 8 3 2 4 1 5 STOP 6 1H 4H 6 9 Light Memory Function: 1. The default light color when the ceiling fan is turned on. 2. The light will lock in a specific color temperature after turning on the light for 10 seconds. 3. The color temperature will be the same as the last time when turning on the light next time. 10 11 BALANCING WEIGHT PLASTIC CLIP 12Corel PDF Engine Version 21.2.0.706 CorelDRAW 2019