kvm-tec KT-6012L CPU MV1 Single Redundant In Copper Instruction Manual

kvm-tec
unua Helpo
MASTERfl ex

Enhavo kaŝi

1 KT-6012L CPU MV1 Single Redundant In Copper

2 Livera Enhavo

3 USING THE ON SCREEN MENU

4 SISTEMA STATUSO

5 VIEWING THE FIRMWARE VERSION

KT-6012L CPU MV1 Single Redundant In Copper

kvm-tec Subteno
[retpoŝte protektita]
Telefono: +43 2253 81912 – 30

6012 SET
MASTERfl ex MV1 SINGLE
REDUNDANT IN COPPER
KT – 6012L CPU/LOCAL
KT – 6012R CON/REMOTE

kvm-tec
Rapida
instalado

Livera Enhavo

LOKA/CPU-Unuo
1 x MA1 local (CPU)
1 x wall power supply! 12V 1A (1NT or EU-plug)
2 x DVI - DVI-kablo 1,8m/5.9ft
1 x US8 canle 1,8m/5.9ft
4 x kaŭĉukaj piedoj
REMOTE/CON-Unuo
1 x MM remote (CON)
1 x wall power supply) 12V 1A (RC orEU-plug)
4x rubber feet

Open OSO menu
The 050 main menu is opened with the standard
shortcut $ x ALT Gr
(Attention: the first 20 seconds S x Saol I always
works, in case the shortcut was forgotten.)
Switching Ilst : CTRL+ALT+PRINT
Changing the shortcuts in the 051) menu
Go to the Remote Settings and then navigate to
Keyboard Shortcut.

Quick Installation Masterflex Single local / CPU – remote / CON

Konektu la CON / Remote kaj la CPU / Lokan Unuon al la inkluzivita 12V 2A nutrado.
Nun konektu la USB-kablon al USB-haveno de via komputilo kaj konektu la alian finon de la USB-kablo al la CPU / Loka Unuo. Konektu klavaron kaj muson al la CON / Malproksima Unuo.
Connect the CPU / Local and the CON / Remote Unit with a network cable.
Now connect the DVI cable to the DVI socket of the PC and the other end to the DVI socket of the CPU Local Unit (PC-in).
Opt: Connect PC audio/out with the audio cable to local audio/in. Connect audio/out via the audio cable
Almost done! Opt: Connect the audio cable local audio/out to the PC audio/in and remote audio/out with audio cable to the microphone
Using a switch: Connect all endpoints to the switch. Ensure that all connections have a bandwith of 1Gbit/sec. For video sharing the network has to support IGMP snooping.

AMUZU - via kvm-tec Extender nun estas uzata dum multaj jaroj (MTBF proksimume 10 jaroj)

USING THE ON SCREEN MENU

Use the monitor and keyboard to use the main menu.
To access the main menu:

Make sure the extenders, the monitors and the computer are switched on.
Press the ALT+GR key on your keyboard quickly five times.
The main menu appears with an overview of the sub-menus.
To open a sub-menu press the applicable key.

Ĉefa Menuo

Ĉefaj Miaj Mallongaj Tranĉoj:
S Statuso Finisview
U Ĝisdatigu Flash FW
F Trajtoj Superview
D DDC Opcio
L Lokaj Agordoj
R Foraj Agordoj
A Pri Finiteview
L Link Redundancy
Q Exit

Menu Status /current status
Ĝisdatigoj de Firmware
Agordoj Trajtoj
DDC Option Fix settings 1020 x 1080
Lokaj agordoj
Agordoj Fora
superview Upgrades Upgrades

SISTEMA STATUSO

duala
In the status overview menu the current status of the extender connection is displayed. It provides information on the connection itself as well as resolution of the video channel, and USBstatus. The enabled options and the current firmware-version is displayed in the left top corner. Link status shows whether there is a physical connection available. Connected indicates if kvm data is currently able to be transmitted. Video and USB show if data is currently being transmitted.

VIEWING THE FIRMWARE VERSION

Under „A“ – About the currently installed fi rmware version of the remote (CON) and local (CPU) Extender is displayed.

FEATURES MENÜ

Features Menu
P Point to Point Mode
M Matrix Switching Mode
D Freeze last Image
E USB Emulation Mode
S USB Save Feature
O Power Redundance Alert
C Diagnosis
U Unlock Features
I IP Management
L Link Redundancy Alert

Ebligita / Malebligita
(Point to Point Point to Point excludes itself
with Matrix mode
Disabled/Enabled
(Disabled)Disabled/Enabled
(Disabled ) Disabled/Enabled
(mass storage usable) Disabled/Enabled
Alerta Sistemo
Diagnosis menu
Unlock Features
IP Management
redundanter Link

PUNKTO AL PUNTO

You can switch the Point to Point mode on and oﬀ by pressing the „P“ key
ATENTO – if the point to point mode is activated, the switching mode cannot be activated

MATRIX SWITCHING MODE
By pressing the „M“ button you can switch the Matrix Switching Mode oﬀ and on

KVM-TEC Gewerbepark Mitterfeld 1 A 2523 Tattendorf Aŭstrio www.kvm-tec.com	KVM-TEC AZIO p +9173573 20204 [retpoŝte protektita] KVM-TEC ĈINIO P + 86 1360 122 8145 [retpoŝte protektita] www.kvm-tec.com
IHSE GmbH Benzstr.1 88094 Oberteuringen Germanio www.ihse.com	IHSE USA LLC 1 Corp.Dr.Suite Cranbury NJ 08512 Usono www.ihseusa.com
IHSE GMBH Azio 158Kallang Vojo, #07-13A 349245 Singapuro www.ihse.com	IHSE Ĉinio Co., Ltd ĉambro 814 Konstruaĵo 3, Kezhu Road Kantono PRC www.ihse.com.cn

Plena HD
super IP
kontrolu
our Installation
kanalo:

http://www.kvm-tec.com/videos/videos-installation-channel

We are here for you to answer your questions about installation? Manual download www.kvm-tec.com or kvm-tec Installationchannel on our homepage personally +43 2253 81912

www.kvm-tec.com

Dokumentoj/Rimedoj

kvm-tec KT-6012L CPU MV1 Single Redundant In Copper [pdf] Instrukcia Manlibro
KT-6012L CPU MV1 Single Redundant In Copper, KT-6012L CPU, MV1 Single Redundant In Copper, Redundant In Copper, In Copper, Copper