Loctite 5188 Gasket Sealant User Manual

Produkto Finisview

The Loctite 5188 Gasket Sealant is an anaerobic flange sealant designed for rigid iron, aluminum, and steel flanged mating surfaces. It cures when confined in the absence of air between close-fitting metal surfaces. This product provides a flexible, solvent-resistant seal that will not tear or degrade. It is ideal for sealing close-fitting joints between rigid metal faces and flanges.

Bildo 1: A red tube of Loctite 5188 Flange Sealant, 50ml size, with white cap and nozzle. The label clearly shows 'LOCTITE 5188 FLANGE SEALANT' and 'NET 1.69 FL. OZ. (50 ml)'.

Sekurecaj Informoj

Always read the Material Safety Data Sheet (MSDS) prior to use. This product contains chemicals that may be harmful if misused. Keep out of reach of children. Use in a well-ventilated area.

• Evitu kontakton kun haŭto kaj okuloj. Okaze de kontakto, tuj lavu per multe da akvo kaj serĉu kuracistan konsilon.
• Do not ingest. If swallowed, do not induce vomiting; call a physician immediately.
• Portu taŭgan personan protektan ekipaĵon (PPE) kiel gantojn kaj sekurecajn okulvitrojn.
• Konservu en malvarmeta, seka loko for de rekta sunlumo kaj varmofontoj.

Setup and Surface Preparation

1. Puraj Surfacoj: Ensure all mating surfaces are clean, dry, and free from oil, grease, and old gasket material. Use a suitable solvent cleaner if necessary.
2. Roughen Surfaces (Optional): For best adhesion, lightly abrade smooth surfaces with an abrasive pad or fine sandpaper, then clean again.
3. Kontrolu Fit: Verify that the parts to be sealed fit closely together. This product is designed for close-fitting metal surfaces.

Operating Instructions (Application)

1. Disdoni Produkton: Apply a continuous bead of Loctite 5188 to one of the flange faces. Ensure complete coverage around all bolt holes and mating surfaces.
2. Kunmeti Partojn: Assemble the components immediately after application. Light clamping is recommended to ensure intimate metal-to-metal contact.
3. Tempo de Resanigo:
   • Fiksa Tempo: The product will fixture (become tack-free) in approximately 20 minutes at room temperature (22°C / 72°F).
   • Full Cure: Full cure is typically achieved within 24 hours.
   • Notu: Cure speed can vary depending on the substrate material, bondline gap, and temperature. Active metals like brass or copper will cure faster, while passive substrates like stainless steel may require an activator (e.g., Loctite 7649) for faster cure.
4. Testado: Allow sufficient cure time before subjecting the assembly to operational pressures or temperatures.

Prizorgado kaj Stokado

• Stokado: Store the product in its original container in a cool, dry location. Optimal storage temperature is between 8°C and 21°C (46°F and 70°F).
• Konsumodaŭro: Refer to the product packaging for specific shelf life information.
• Purigado: Uncured product can be cleaned with organic solvents. Cured product must be removed mechanically (e.g., scraping).
• Forigo: Dispose of product and packaging in accordance with local, regional, national, and international regulations.

Solvado de problemoj

Specifoj

• Produkta Tipo: Anaerobic Gasket Sealant
• Modela Nombro: 1253203
• Volumo: 50 mL (1.69 fl. oz.)
• Koloro: Ruĝa
• Temperaturintervalo: -65 °F ĝis 300 °F (-54 °C ĝis 149 °C)
• Fiksa Tempo: Approximately 20 minutes (on steel)
• Plena Kuracia Tempo: 24 horoj
• Fleksebleco: Tre Fleksebla
• Fabrikisto: Loctite (Henkel)
• Country of Manufacturer: Usono

Subtenaj Informoj

For technical assistance, product inquiries, or safety data sheets, please visit the official Loctite webretejo aŭ kontaktu ilian klientan subtenon.

Loctite Official Webretejo: www.loctite.com

Amazon-markbutiko: Visit the Loctite Store on Amazon