manhattan 154116 2D Long Range LED Barcode Scanner User Manual

Basic Information
The user manual provides details on interface mode settings, function settings (lighting, keyboard type, factory reset, etc.), symbology settings, exposure optimization in special scenes, and data format editing functions.
USB Cable Connection
Ensure the scanner is connected to a compatible USB port using the provided USB cable.
Decoding
Follow the decoding instructions provided in the manual to correctly interpret scanned barcodes.
System Settings
Access the system settings to check the version number, recover default settings, and configure the interface mode.
Barcode Symbology Configuration
Adjust barcode enable/disable settings, barcode length settings, ISBN 13 conversion settings, GS character conversion, GS output mode, code ID settings, and control character output as needed.

FAQ

Q: Can I use this scanner with a Mac computer?
A: Yes, the Manhattan 2D Long Range LED Barcode Scanner is compatible with Mac computers.
Q: How do I reset the scanner to factory defaults?
A: To reset the scanner to factory defaults, refer to the manual for instructions on recovering the default settings.

All trademarks and trade names are the property of their respective owners. © IC Intracom. All rights reserved. Manhattan is a trademark of IC Intracom, registered in the U.S. and other countries. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated, or converted to any electronic medium or machine-readable form without the prior written consent of the maker. Thank you for purchasing the Manhattan 2D Long Range LED Barcode Scanner. Before using this product, carefully read the manual to understand its functions.

BASIC INFORMATION

ABOUT THE MANUAL
This user manual includes interface mode settings, function settings (lighting, keyboard type factory reset, etc.), symbology settings, exposure optimization in special scenes, and data format editing functions. If you need to change the function you need, scan the corresponding configuration code below. All bands (*) indicate factory default values.

PACKAGE DETAILS

ITEM	SPECIFICATION / MODEL	NUMBER	NOTE
Barcode scanner	2D Long Range LED Barcode Scanner	1
Data Cable	USB	1
Quick Installation Guide	Paper	1

APPEARANCE SIZE

INTERFACE

USB CABLE CONNECTION

Insert the RJ45 interface (crystal head) of the USB data cable into the rear of the scanner, there is a crisp “click” sound, and the connection is normal.
Connect the USB interface of the USB data cable to the host device.

DECODING

Make sure that both ends of the cable are properly connected to the scanner and the host, and that there is a prompt sound when starting.
Press the button, and the fill light of the window is on, accompanied by a green dot.
Aim the green dot at the barcode. After the reading is successful, the scanner will sound a beep, and turn off the fill light and aiming light. After the data is transmitted to the host, press the switch again to read the barcode.
In the process of reading the barcode, the different sizes and densities of the barcode, and the effective reading distances are also different. When there is difficulty in reading, the scanner can be moved back and forth, adjusting the distance between the scanner and the barcode to improve the success rate of reading.

SYSTEM SETTINGS

CHECK THE VERSION NUMBER
Read the “Version Information” barcode, the scanner will output the software version.

RECOVER THE DEFAULT SETTING
Restore the system setting state to the default setting state. The scanner will restart automatically after setting.

INTERFACE MODE

USB HID INTERFACE
When the data cable with USB interface, after reading the “USB HID” barcode, the scanner will be set to the “USB Keyboard” mode, and the scanner will input data to the host by pressing the keyboard button first.

When the data output is wrong, please turn off the third-party output method and use the American English keyboard, because the third-party input method will edit the input data for a second time before outputting, and the data output will be incomplete, wrong, or garbled.

USB TRANSMISSION RATE
The USB Transmission Rate can be set to three levels: high, medium, and low. The higher the rate, the faster the characters are transmitted to the host.

USB TRANSMISSION DELAY
The USB Transmission Delay can be set to four gears from 0 to 3. If the host will lose characters, the delay can be increased.

EMULATE KEYBOARD
When the emulate keyboard input character is enabled, the character will be sent through the numeric keypad, ignoring the national keyboard layout setting;

EXAMPLE
Assume that the current scanner reads the barcode with the content “A§F” (the decimal value in Code Page 1252 is 65/167/66 respectively). If the keyboard emulation input character is set to “on”, the scanner emulates the keyboard operation as follows:

Enter “A” — press the ALT key, simultaneously press the numeric keypad keys 0, 6, 5 in sequence, and release the ALT key;
Enter “§” — press the ALT key, simultaneously press the numeric keypad keys 1, 6, 7 in sequence, and release the ALT key;
Enter “B” – press the ALT key, simultaneously press the numeric keypad keys 0, 6, and 6 in sequence, and release the ALT key.

KEYBOARD LANGUAGE COUNTRY TYPE
When the barcode scanner is used as a keyboard input device by default, some characters are different in different countries, and different national languages need to be set. The keyboard defaults to the US language.

KEYBOARD MODE ENCODING FORMAT
The keyboard mode can output Chinese, traditional Chinese, Korean, etc. Since the third-party software uses a different encoding, the scanner needs to switch to different encoding formats, please scan the corresponding configuration code as required.

CTRL+* MODE SEND

After this function is enabled, the control characters from 00 to 1F in the ASCII code table will be output by the combination of CTRL+*.
For the corresponding relationship between the specific ASCII value and the control function keys, see the attached table.

NON- PRINTABLE		KEYBOARD *CONTROL + ASCII (CTRL+) MODE**
DEC	HEX	CHAR	CONTROL + * MODE OFF	*WINDOWS MODE CONTROL + MODE ON**
DEC	HEX	CHAR	CONTROL + * MODE OFF	CTRL+ *	*CTRL + FUNCTION**
0	00	NUL	NULL	CTRL + @
1	01	SOH	NP Enter	CTRL + A	Select All
2	02	STX	Caps Lock	CTRL + B	Bold
3	03	ETX	Right Arrow	CTRL + C	Copy
4	04	EOT	Up Arrow	CTRL + D	Bookmark
5	05	ENQ	NULL	CTRL + E	Center
6	06	ACK	NULL	CTRL + F	Find
7	07	BEL	Enter	CTRL + G
8	08	BS	Left Arrow	CTRL + H	History
9	09	HT	Tab	CTRL + I	Italic
10	0A	LF	Down Arrow	CTRL + J	Justify

11	0B	VT	Tab	CTRL + K	Hyperlink
12	0C	FF	Backspace	CTRL + L	List, Left Align
13	0D	CR	Enter / Ret	CTRL + M
14	0E	SO	Insert	CTRL + N	New
15	0F	SI	ESC	CTRL + O	Open
16	10	DLE	F11	CTRL + P	Print
17	11	DC1	Home	CTRL + Q	Quit
18	12	DC2	PrtScn	CTRL + R
19	13	DC3	Delete	CTRL + S	Save
20	14	DC4	Tab + Shift	CTRL + T
21	15	NAK	F12	CTRL + U
22	16	SYN	F1	CTRL + V	Paste
23	17	ETB	F2	CTRL + W
24	18	CAN	F3	CTRL + X
25	19	EM	F4	CTRL + Y
26	1A	SUB	F5	CTRL + Z
27	1B	ESC	F6	CTRL + [
28	1C	FS	F7	CTRL + \
29	1D	GS	F8	CTRL + ]
30	1E	RS	F9	CTRL + ^
31	1F	US	F10	CTRL + –
127	7F	DEL	Delete

USB COM INTERFACE

In this section, you can change the reading mode of the device, you only need to scan the corresponding setting code according to your needs.
After the scanner of the USB interface is set to “USB COM”, the data will be transmitted to the host through the serial port;

READING MODE
The stop digit is located at the last part of each byte transmitted and is used to mark the completion of the transmission of this byte to start receiving the next byte of data.

MODE	DESCRIPTION
Manual
Automatic	After power on, it has been in the state of reading codes. Pressing and releasing the button can briefly switch the scanner between manual and automatic states. In this mode, the reread delay can be used to prevent the same barcode from being read multiple times.
Multiple Reading	When the button is pressed, the scanner starts to read the barcode, and it stops reading the barcode until the button is released. When the key is pressed and the code is successfully read, there will be a prompt tone and the barcode information will be output. As long as the key is not released, the scanner will continue to read the barcode. The same barcode is only allowed to be read and output once while the key is pressed.
Good Read Off	When the button is pressed, the scanner starts to read the barcode and stops reading the barcode until the barcode reading is successful or the set time of a code reading timeout is reached. In this mode, a barcode reading timeout starts from the time the button is released.
Auto-Sense	The scanner enters the induction mode, which can be used with a stand. When an object passes through the scanning window, the scanner will be awakened, the fill light will be lit, and the code will be read. When the decoding time is exceeded, the fill light is turned off.

THE SAME BARCODE DELAY

The same barcode delay only takes effect in automatic mode. After reading a barcode in automatic mode, it will refuse to read the same barcode within the set period. It can be read and output only after the period is exceeded.
The same barcode time can be set to 1~127 (min. is 1, max. is 127), and can be edited freely with barcode software, choose to use CODE128 code. “7EFD6X”(X means
the same barcode interval time, 1 means 50ms, 127 means 127*50ms ).

BARCODE READING TIMEOUT

AUTOSENSE SENSITIVITY SETTINGS
Sensitivity is 15 classes (B67A61 to BA67A615), class 1 highest, class 15 lowest.

LIGHT SETTING
POSITION LIGHT (AIMER)

BEEPER SETTING

BEEPER FREQUENCY SETTING

VIBRATION SETTING

OUTPUT SETTING
In this chapter, you can configure the output of the device, including carriage return/line feed, serial port encoding setting, setting barcode length, removing barcode digits (remove/keep from beginning and ending), and multi-countries keyboard switching settings, etc. You only need to read the barcode according to the requirements.

CARRIAGE RETURN/LINE FEED SETTING

CASE CONVERSION

Letter conversion: when outputting barcodes with letter content, you can configure the output result to be all uppercase or all lowercase.
For example: the barcode content is ab12DE, if you scan the “all uppercase” barcode, the output result will be AB12DE; if you scan the “all lowercase” barcode, the output result will be abc12de; if you scan the “case conversion” barcode, the output result will be AB12de; the default case is not converted.

CAPS LOCK DETENTION

REMOVE DIGITS FROM THE BEGINNING/ENDING
Remove digits from Beginning/Ending can be used at the same time.

MODE	DESCRIPTION
Remove digits from the Beginning	“B68E6X” (X is the number of digits to remove. If the last number is 1, it means remove one digit; if it is 2, remove two digits; if it is 0, it is not removed.)
Remove digits from Ending.	“B6BE6X” (X is the number of digits to remove. If the last number is 1, it means remove one digit; if it is 2, remove two digits; if it is 0, it is not removed.)

KEEP DATA FROM START/END

You can only choose to keep the beginning or ending digit, but not both. Scan “AC8760” from the digit of the reserved barcode at the beginning, scan “AC8761” from the digit of the reserved barcode at the ending, and then scan the reserved digit barcode, “B69E6X” X is the digit of the reserved data.
For example, if 9 bits are reserved, the maximum number of B69E69 is 255.

Keeping the header or keeping the tail data is a single option and cannot take effect at the same time. When it is used in combination with the delete data set, the data will be edited and output in the order of the settings.

BARCODE SYMBOLOGY CONFIGURATION

This chapter can configure the Barcode Symbology Configuration of the device, including barcode enable/disable, check enable/disable, check output enable/disable, etc.

QUICK SETTING OF BARCODE ENABLE/DISABLE SETTING

BARCODE LENGTH SETTING
The barcode length setting code can be edited freely with barcode software, and CODE128 can be selected. For example, the minimum length setting of Telepan is ^3B76E61, 1 means that the barcode with a minimum length of 1 digit can be read, and the maximum length setting code is ^3B77E6255, which means the barcode with a maximum length of 255 digits can be read.

TELEPEN LENGTH LIMIT

MATRIX 25 LENGTH LIMIT

CHINA POST (DATALOGIC 2 OF 5) LENGTH LIMIT

CODE 11 LENGTH LIMIT

CODEABAR LENGTH LIMIT

INTERLEAVED25 LENGTH LIMIT

CODE 128 LENGTH LIMIT

CODE 93 LENGTH LIMIT

CODE 39 LENGTH LIMIT

2D BARCODE LENGTH SETTING
The minimum length of the 2D barcode can be set to 1~255 (the minimum length is 1, the maximum length is 255), 67EE6X (X represents the length of the barcode)

2D barcode length lock: After locking, only fixed-length 2D barcodes can be read, 67FE6X (X represents the data length)
Setting an example: ^367FE620, the last two digits of “20” represent only read the 2D barcode with a barcode data length of 20 digits;

AIRLINE 2 OF 5 (STANDARD 2 OF 5/IATA 2 OF 5)

AZTEC CODE

CODABAR

CODABLOCK A

CODABLOCK F

CODE 128

CODE 11

CODE 32

CODE 39

CODE 93

COMPOSITE
To enable this symbology, both Micro PDF and RSS-14 must be enabled at the same time.

DATA MATRIX CODE

DOT-CODE

EAN/UPC

EAN-8

EAN-13

GS1 DATABAR EXPANDED

GS1 DATABAR LIMITED

GS1 DATABAR OMNIDIRECTIONAL

HANXIN

HONG KONG 2 OF 5(CHINA POST)

When reading a postal, all other postal needs close.

INTERLEAVED 2 OF 5

MATRIX 2 OF 5

MAXICODE

MSI

MICRO PDF417

PDF417

PHARMACODE

MICRO QR CODE

QR CODE

RSS-14

RSS-LIMITED

RSS-EXPANDED

STRAIGHT 2 OF 5 INDUSTRIAL

TELEPEN

TRIOPTIC CODE

UPC-A

UPC-E

GRIDMATRIX

ISBN 13 CONVERSION SETTING

GS CHARACTER CONVERSION

This mode is to output GS control characters as text characters.

GS OUTPUT MODE

CODE ID SETTING

ANNEX: CODE ID TABLE

BARCODE	CODE ID	BARCODE	CODE ID
Airline 2 of 5 (Standard 2 of 5/IATA 2 of 5)	f	HANXIN	H
Aztec Code	z	Interleaved 2 of 5	e
Codabar	a	Hong Kong 2 of 5(China post)	Q
Codablock A	V	Matrix 2 of 5	m
Codablock F	q	Maxicode
Code 128	j	MSI	g
Code 11	h	Micro PDF417	R
Code 32	<	PDF417	r
Code 39	b	Pharmacode
Code 93	i	Micro QR Code	s
Composite	!	QR Code	s
Data Matrix	w	RSS-14	y
EAN-8	D	RSS-Limited	{
EAN-13	d	RSS-Expanded	}
GS1 DataBar Expanded	}	Straight 2 of 5 Industrial	f
GS1 DataBar Limited	{	Telepen	t
GS1 DataBar Omnidirectional	y	Trioptic Code	=
UPC-A	c	DOT_Code	.
UPC-E	E	ISBN 13	d
GridMatrix	X	ISSN	d

CONTROL CHARACTER OUTPUT

After this function is enabled, control characters (invisible characters) are output as text characters, for example, carriage return is output as <CR>.

Due to product improvement programs, specifications and features are subject to change without prior notice.

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT

DISPOSAL OF ELECTRIC AND ELECTRONIC EQUIPMENT
(Applicable In The European Union And Other European Countries With Separate Collection Systems)

This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. By EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be disposed of by the user’s local regulations for electrical or electronic waste. Please dispose of this product by returning it to your local point of sale or recycling pickup point in your municipality.

WARRANTY INFORMATION

manhattanproducts.com.

REGULATORY STATEMENTS

FCC Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used under the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver; connect the equipment to an outlet on a circuit different from the receiver; or consult the dealer or an experienced radio/TV technician for help.

CE
This device complies with the requirements of CE 2014/30/EU and/or 2014/35/EU. The Declaration of Conformity is available at: support.manhattanproducts.com/barcode/154116.

North America
IC Intracom America 550 Commerce Blvd. Oldsmar, FL 34677 USA
Asia & Africa
IC Intracom Asia 4-F, No. 77, Sec. 1, Xintai 5th Rd. Xizhi Dist., New Taipei City 221, Taiwan
Europe
IC Intracom Europe Löhbacher Str. 7, D-58553 Halver, Germany

All trademarks and trade names are the property of their respective owners. manhattanproducts.com.

Documents / Resources

	manhattan 154116 2D Long Range LED Barcode Scanner [pdf] User Manual 154116 2D Long Range LED Barcode Scanner, 154116, 2D Long Range LED Barcode Scanner, Range LED Barcode Scanner, Barcode Scanner, Scanner
	manhattan 154116 2D Long Range LED Barcode Scanner [pdf] Instructions 154116, 154116 2D Long Range LED Barcode Scanner, 2D Long Range LED Barcode Scanner, Long Range LED Barcode Scanner, LED Barcode Scanner, Barcode Scanner, Scanner

References

User Manual

manhattan 154116 2D Long Range LED Barcode Scanner

Product Information

Product Usage Instructions