ELSEMA PCR433WG 433MHz Penta Receiver with Wiegand Output

Features

• Easy to add remote controls to any Wiegand input access control panel
• Remotes are added like cards or RFID tags with no software changes
• Wireless keyless entry offers convenience, security and safety for accessing gates, doors and boom gates
• Wide operating supply voltage and low current consumption
• Easy way to facilitate for handicapped access
• Compatible with PentaCODE® remotes
• Easy to use dipswitch coding

Applications
Keyless access control for automatic gates, doors and boom gates

Description

This receiver allows you to add wireless remote controls to your existing access control systems by connecting the PCR433WG receiver to the access system. The remote controls have a range of up to 200 metres (650 feet) and are available with 2 or 4 buttons. The extra buttons can be used as a panic button allowing a single remote to allow access control and panic alert system. The receivers Wiegand output interfaces to virtually any commercial access control panel. Remote controls are added as easily as Wiegand cards or RFID tags without any software changes. The ID and facility codes can be matched to the system requirements. The receiver has a bi-colour LED to act as a status display. Red LED indicates that AC or DC power is “On” and Green LED indicates remote control signal has been received.

Setup Instructions

The Penta receiver has a 12-way dipswitch, where switches 1-8 sets the site code. Dip Switch 10, 11 & 12 selects the button that the PCR433WG receives from the PentaCODE® Remote.

The user code is set by the 12-way dipswitch on the remote. Each remote should have a unique code to identify each user. Remotes are programmed into the access controller in the same way as RFID tags. When programming instead of swiping the RFID tags, the remote button is pressed. On the PentaCODE® remotes you need to have at least 1 of the 12 switches “On” for the  remote to work. The receiver comes pre-wired in a small 70 x 55 x 25 mm enclosure and a supply of 12 to 24 Volts AC or DC can be connected.

The 26 bit Wiegand data output from the PCR433WG is as shown below. You can change the 12 way Dip Switch on the transmitter to change the serial code. However each button on the transmitter will send a different code.

• Site Code: Dip Sw 1-8 on Receiver (PCR433WG)
• Serial Code: Dip Sw 1-12 on Tx + Button Pressed
• Bit 1 = Leading Parity Bit
• Bit 2 = Receiver Dip Switch 8
• Bit 3 = Receiver Dip Switch 7
• Bit 4 = Receiver Dip Switch 6
• Bit 5 = Receiver Dip Switch 5
• Bit 6 = Receiver Dip Switch 4
• Bit 7 = Receiver Dip Switch 3
• Bit 8 = Receiver Dip Switch 2
• Bit 9 = Receiver Dip Switch 1
• Bit 10 = Transmitter Button 4
• Bit 11 = Transmitter Button 3
• Bit 12 = Transmitter Button 2
• Bit 13 = Transmitter Button 1
• Bit 14 = Transmitter Dip Switch 12
• Bit 15 = Transmitter Dip Switch 11
• Bit 16 = Transmitter Dip Switch 10
• Bit 17 = Transmitter Dip Switch 9
• Bit 18 = Transmitter Dip Switch 8
• Bit 19 = Transmitter Dip Switch 7
• Bit 20 = Transmitter Dip Switch 6
• Bit 21 = Transmitter Dip Switch 5
• Bit 22 = Transmitter Dip Switch 4
• Bit 23 = Transmitter Dip Switch 3
• Bit 24 = Transmitter Dip Switch 2
• Bit 25 = Transmitter Dip Switch 1
• Bit 26 = Trailing Parity Bit

Products in the Range

LED Indicator

Technical Data

Block Diagram

Documents / Resources

ELSEMA PCR433WG 433MHz Penta Receiver with Wiegand Output [pdf] Instructions PCR433WG 433MHz Penta Receiver with Wiegand Output, PCR433WG, 433MHz Penta Receiver with Wiegand Output, Penta Receiver with Wiegand Output, Wiegand Output

References

• User Manual