Categories: ELRO

ELRO FC480111R Connects Carbon Monoxide Detector User Manual

ELRO FC480111R Connects Carbon Monoxide Detector

INSTALLATION

Instruction manual

Manufacturer
Sitwell Electronics CO., Limited No.666 Qingfeng Road, Jiangbei District, Ningbo, Zhejiang Province, China 315034
Importer:

  • ELRO Europe | www.elro.eu
  • Postbus 9607 – Box E800
  • 1006 GC Amsterdam The Netherlands
  • Type A apparatus
  • EN50291-1:2010+A1:2012

Congratulations on the purchase of this ELRO carbon monoxide detector! Read these instructions carefully and store them in a safe place for future usage.

WARNINGS

  • The installation of a CO-detector should not be used as a substitute for proper installation, use and maintenance of fuel-burning appliances including appropriate venison and exhaust systems.
  • Risk of electric shock or malfunction if the apparatus is
    tampered with.
  • The following substances can affect the sensor and may cause false alarms: methane, propane, isobutene, isopropanol, ethylene, benzene, toluene, ethyl acetate, hydrogen sulfide, sulfur dioxides, alcohol-based products, paints, thinner, solvents, adhesives, hair sprays, aner shaves, perfumes and some cleaning agents.
  • To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
  • The apparatus should be installed by a competent person.
  • Babies should not be exposed to excessive heat, such as sunshine or fire.

Product Overview

  • Power indicator green b. Fault indicator yellow
  • Alarm indicator red d. Test/Silence button e. Alarm sounder

Ac date your carbon monoxide detector

  • Open battery department
  • Place battery
  • Close battery department
    If ac is voted correctly, all LEDs will light up you will hear a beep.
  • The next 30 seconds: The green LED will flash every 3 seconds to indicate that the device is in the preparation stage.
  • After 30 seconds: the power indicator will flash every 30 seconds and the action has succeeded. Test the alarm by pressing the test button for 0.2 seconds, the device enters the “Test mode“.

Locate your device

Potential sources of carbon monoxide are wood-burning stoves, gas boilers and fires, gas hobs, oil and coal-burning appliances, portable gas heaters, barbecues etc.

Where to install an apparatus?

  • Ideally: in every room containing a fuel-burning appliance and
    additional apparatuses:
    • In every bedroom
    • In every room where much tme is spent and the alarm sound from other apparatuses may not be heard
  • If the number of available apparatuses is limited, then choose
    for the room where:
    • A flueless or open-flued appliance is located
    • Where you spend the most tme
  • In case of bedsit (single room serving as both sitng room and bedroom): locate the apparatus as far as possible from the cooking appliances and near the sleeping area.
  • In rooms with a fuel-burning appliance:
    • Between 1-3 m distance away from the potential source
    • If there is a partition in the room: at the same side of the partition as the potential source
    • On the wall:
      1. Close to the ceiling, but at least 150 mm from the ceiling
      2. Higher than the height of any door/window
  • In rooms without a fuel-burning appliance (such as sleeping rooms/hallways:
    • Relatively close to the breathing zones of occupants

Where not to install an apparatus
In an enclosed space (in a cupboard/behind a curtain). Where it can be obstructed (by for example furniture). Directly above a sink. Next to door/window. Next to an extractor fan. Next to an air vent / similar ventilation openings. In areas where temperature get <-10 / >40 degrees. In areas where dirt/dust may block the sensor. In a damp/ humid locaon. In the immediate vicinity of cooking appliances. On a location where light indicator may not be visible anymore

Mount the alarm

  1. Drill two holes in the wall of 5 mm and insert the plastic plugs.
  2. Insert the screws until they are about 5 mm from the wall
  3. Place the unit over the screws

Connect your devices (ELRO Connects) to each other

  1. Select a random device to be the master device. Enter the network mode of this device by pressing test buttn 3 tmes in 2 seconds. The red LED light will light up for 10 seconds.
  2. Take the next device and press test button 3 times in 2 seconds. The product will automatically connect to the master device.
    If the connection is successful, the red LED flashed a few tmes and both devices will beep.
  3. Repeat step to for the third, fourth etc. device you want to connect.
  4. Test the functionality of devices by pressing the test button of random devices. All connected devices will ring one by one in the following seconds.

Important: Keep in mind that if you want to connect additional devices, you should always enter the network mode with the inital selected master device.

Reset connections

  1. Remove the battery of a random device
  2. Press and hold the test but and place the battery. When the battery is placed, the red LED light will light up for 5 seconds.
  3. When the LED turns of, release the test button.
  4. Red LED-light will light up for 3 seconds. Press the test button while the red LED light is still lit.
  5. If network is successfully cleared, the product will beep

Alarm silence mode
Before putting an alarm, always make sure the alarm is false. In case of doubt, take the necessary action! To mute the alarm, press the test button. The alarm will pause for 5 minutes while the alarm indicator keeps flashing. All connected devices will be muted too. The alarm will return to alarm mode if the concentration of CO is still>45 ppm.

What to do if carbon monoxide is detected?
If the carbon monoxide detector gives the alarm, please take the following actions:

  • Keep calm and open all doors and windows. Stop using fuel-burning appliances and turn them off;
  • If the alarm continues, evacuate the building. Leave all doors and windows open, and do not enter before the alarm has stopped;
  • Get medical help for anyone who is suffering the effects of carbon monoxide poisoning;
  • Contact the appropriate maintenance agency. Do not use fuel-burning appliances until they are checked by a competent person.

Maintenance

  • Test your Carbon Monoxide alarm every month by pressing the test button for 0.2 seconds.
    • If the device functions properly, the red LED light will flash four times and it will beep simultaneously. If you do not hear a beep or see a light after the test, the device is not functioning correctly and should be replaced as soon as possible!
  • Replace the batteries. If the batteries are running low the yellow LED will flash 2x every 30 seconds and a beep will sound twice every 30 seconds. If this occurs, replace the batteries as soon as possible:
    • Open battery department
    • Place battery
    • Close battery department

Warning: Always test the alarm after replacing the batteries by pressing the test button
Warning: Replace only by the following battery types:

The effects of Carbon Monoxide
Carbon monoxide is a colorless, odorless, non-irritating gas that is classified as a chemical asphyxiant, whose toxic action is a direct result of the hypoxia produced by a given exposure.
Health effects on healthy adults:

Concentration

  • 100-200 PPM Slight headache, weakness, potential burden on the fetus
  • 200-300 PPM Severe headache, nausea, impairment in limb movements
  • 300-400 PPM Severe headache, irritability, confusion, impairment in visual acuity, nausea, muscular weakness, dizziness, weakness
  • 400-500 PPM Convulsions and unconsciousness
  • 600-700 PPM Coma, collapse, death

Specifications

  • Battery type : 2x 1,5V alkaline (3V DC)
  • Battery lifetime: 1 year
  • Type apparatus: Type A
  • Sensor: Electrochemical
  • Alarm volume : > 85 dB (A) at 1 meters.
  • Product Ilifetime: 10 years after initial activation

Operation Ambient Condition:
10°C +40°C, 30~ 95% non-condensing

Storage/Transport Ambient Condition:
20°C +50°C, 10 95% non-condensing

Symbols

Recycling and disposal: The WEEE symbol (a) means that this product and batteries must be disposed of separately from other household waste. When it reaches its end of life, take it to a designated waste collection point in your area to guarantee safe disposal or recycling. Protect the environment, human health, and natural resources! Read the manual (b) before use and store it in a safe place for future use and maintenance. Download (c) Declaration of Performance (DoP) at www.euro.EU.

Documents / Resources

ELRO FC480111R Connects Carbon Monoxide Detector [pdf] User Manual
FC480111R, Connects Carbon Monoxide Detector, FC480111R Connects Carbon Monoxide Detector, Carbon Monoxide Detector, Monoxide Detector, Detector

References

Recent Posts

Optimus H-3013 Portable Utility Thermostat

Optimus H-3013 Portable Utility Thermostat Specifications Brand  Optimus Color   Gray Heating Method          Fan &…

2 mins ago

VISION1RACING Shift Selector Springs Race Kit Instructions

Shift Selector Springs Race Kit Shift Selector Springs ­ Race Kit Nissan FWD 6spd (F51)…

4 mins ago

Panasonic FV-SW20VEC1 LCD Wired Wall Control Panel Instruction Manual

FV-SW20VEC1 LCD Wired Wall Control Panel

4 mins ago

WOLF TOOTH B-RAD Double Bottle Adapter User Guide

B-RAD Double Bottle Adapter DOGBONE BASE BoTTLE SHIFT BASE 3.0in (76mm) 2-slot BASE 3-slot BASE…

12 mins ago

PARIS RHÔNE PE-HE006 Fast Heating Electric Space

PARIS RHÔNE PE-HE006 Fast Heating Electric Space Specifications BRAND: PARIS RHÔNE COLOR: Black POWER SOURCE:…

14 mins ago

MEMPHIS AUDIO MXASB35V3 35 Inch Clamp Mount Soundbar Instruction Manual

MXASB35V3 35 Inch Clamp Mount Soundbar PAIRING DEVICES In Bluetooth mode, device will be automatically…

15 mins ago