ELATION-logo

ELATION PROFESSIONAL CHORUS LINE 16 RGBW LED Bar

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-product

©2020 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | [email protected] Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

+ 31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | [email protected] Elation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000
+ 52 (728) 282-7070

DOCUM ENT VERSION

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig1

Due to additional product features and/or enhancements, an updated version of this document may be available online. Please scan the QR Code with your mobile device or visit www.elationlighting.com for the latest revision/update of this manual, before beginning installation and/or programming.

GENERAL INFORMAT I ON

INTRODUCTION
This fixture has been designed to perform reliably for years when the information in this manual are followed. Please read and understand all the instructions and guidelines carefully and thoroughly before operating this unit. This manual contains important information regarding safety, installation, use, and maintenance.

UNPACKING
Each fixture has been thoroughly tested and shipped in perfect operating condition. Carefully check the outer shipping carton for signs of any damage that may have occurred during shipping. If the outer carton appears to be damaged, carefully inspect the fixture for damage and be sure all included accessories have arrived intact. In the event damage has been found and/or parts are missing, please contact our customer support team for further instructions. Please do NOT return this fixture to your dealer without first contacting customer support at the number listed below. Please do NOT discard the outer shipping carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT
Elation Professional provides a customer support line to provide set up help and answer any set up or operation questions. You may also visit us on the web at www.elationlighting.com for any comments or suggestions. For service-related issue please contact Elation Professional.
ELATION SERVICE USA – Monday – Friday 8:00am to 5:00pm PST
Voice: 323-582-3322 Fax: 323-832-9142
E-mail: [email protected]
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 30 Fax: +31 45 546 85 96
E-mail: [email protected]

WARRANTY REGISTRATION / RETURNS
Please register online: http://www.elationlighting.com/Login.aspx to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support.

LI MI TED WARRANTY ( USA ONLY)

  • Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years (730 days), and Elation Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months (180 days), from the original date of purchase. This warranty excludes discharge lamps and all product accessories. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
    B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return shipping charges only to a designated point within the United States. If any product is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional shall have no liability whatsoever for loss and/or or damage to any such accessories, nor for the safe return thereof.
  •  This warranty is void if the product serial number and/or labels are altered or removed; if the product is modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional; if the product is damaged because not properly maintained as set forth in the product instructions, guidelines and/or user manual.
  •  This is not a service contract, and this warranty does not include any maintenance, cleaning, or periodic check-up. During the periods as specified above, Elation Professional will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.
  • Elation Professional reserves the right to make changes in design and/or performance improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
  •  No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional be liable for any loss and/or damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product.
  • This warranty is the only written warranty applicable to Elation Professional products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

SAFETY GUI DELI NES

This fixture is a sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow all instructions and guidelines in this manual. Elation Professional is not responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of this fixture and only the original rigging parts (omega brackets) included with this fixture should be used for installation. Any modifications to the fixture and/or the included mounting hardware will void the original manufactures warranty and increase the risk of damage and/or personal injury.

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig2

  1. PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED
  2. THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
    DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
  3. DO NOT PLUG FIXTURE INTO A DIMMER PACK!
    NEVER OPEN THIS FIXTURE WHILE IN USE!
    UNPLUG POWER BEFORE SERVICING FIXTURE!
    NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
    KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
  4. NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
    RETINA INJURY RISK – MAY INDUCE BLINDNESS!
    SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
  5. INDOOR / DRY LOCATIONS USE ONLY!
    DO NOT EXPOSE FIXTURE TO RAIN AND/OR MOISTURE!

SAFETY GUI DELI NES

DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before serving.
DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
DO NOT operate fixture if the power cord is frayed, crimped, damaged and/or if any of the power cord connectors are damaged and do not insert into the fixture securely with ease. NEVER force a power cord connector into the fixture. If the power cord or any of its connectors are damaged, replace it immediately with a new one of similar power rating.
DO NOT block any air ventilation slots.
All fan and air inlets must remain clean and never blocked.
Allow approx. 6” (15cm) between fixture and other devices or a wall for proper cooling.
When installing fixture in a suspended environment, always use mounting hardware that is no less than M10 x 25 mm, and always install fixture with an appropriately rated safety cable.
Always disconnect fixture from main power source before performing any type of service and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord.
During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time.

Consistent operational breaks will ensure fixture will function properly for many years. ONLY use the original packaging and materials to transport the fixture in for service.

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE! 

CLEANING
Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics. Clean the external lens surface at least every 20 days with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE
Regular inspections are recommended to insure proper function and extended life.
There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
A detailed review by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall.
Check for any deformations on the housing, color lenses, rigging hardware and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s).
Electric power supply cables must not show any damage, material fatigue or sediments. NEVER remove the ground prong from the power cable.

FIXTURE OVERVIEW

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig3

  1.  LCD Menu Display, MENU, UP, DOWN, ENTER Buttons
  2.  Tilt Lock
  3.  Fuse
  4.  Power IN/OUT
  5.  5pin DMX IN/OUT
  6.  RJ45 Ethernet IN/OUT

INCLUDED ITEMS

  • (2) Replacement Lens Covers
  • (2) Omega Brackets
  • (1) Power Cable

INSTALLATION INSTRUCTIONS

  • FLAMMABLE MATERIAL WARNING
    Keep fixture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.
  • ELECTRICAL CONNECTIONS
    A qualified electrician should be used for all electrical connections and/or installations.
  • USE CAUTION WHEN POWER LINKING OTHER MODEL FIXTURES AS THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR MAX AMPS.
  • DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
Before rigging/mounting a single fixture or multiple interconnected fixtures for custom matrix designs to any metal truss/structure or placing the fixture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certified to safely hold the combined weight of the fixture(s), clamps, cables, and accessories.
Fixture ambient operating temperature range is 15° to 113°F. (-15° to 45°C)
Do not use the fixture under or above this temperature.
Fixture(s) should be installed in areas outside walking paths, seating areas, or away from areas where unauthorized personnel might reach the fixture by hand.
NEVER stand directly below the fixture(s) when rigging, removing or servicing.
Overhead fixture installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable that can hold 10 times the weight of the fixture.
Allow approximately 15 minutes for the fixture to cool down before serving.

CLAMP MOUNTING
The fixture can be placed on the flat surface or truss mounted. When mounting this fixture to truss be sure to secure (2) appropriately rated clamps (not included) to the (2) Omega Brackets (included) Be sure to attach the Safety Cable (included) to the fixture using the safety cable rigging points integrated into the bottom of the fixture. (See image below)

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig4

SAFETY CABLE
The fixture includes an integrated safety cable rigging point. (see image below)

WARNING
ALWAYS ATTACH A SAFETY CABLE WHEN INSTALLING FIXTURE IN A SUSPENDED

OVERHEAD RIGGING
Overhead rigging requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury and property damage. Fixture is fully operational in the specific mounting positions illustrated below.ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig5

POWER LINKING

USE CAUTION WHEN POWER LINKING OTHER MODEL FIXTURES AS THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR AMX AMPS.

KLING-NET / ART-NET CONNECTION
When connecting fixture to a network switch to control multiple devices, a Gigabit Ethernet Switch that supports IGMP (Internet Group Management Protocol) is required. Using a Gigabit Ethernet Switch that does not support IGMP can cause erratic behavior of all connected devices to the switch. Click link below for more information about IGMP.
https://en.wikipedia.org/wiki/Internet_Group_Management_Protocol

SYSTEM MENU

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig6

The fixture comes with an easy to navigate system menu. The control panel (see image below) located on the back of the fixture provides access to the main system menu and is where all necessary system adjustments are made to the fixture. During normal operation, pressing MODE button once will access the fixture’s main menu. Once in the main menu you can navigate through the different functions and access the sub-menus with the UP and DOWN buttons. Once you reach a field that requires adjusting, press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field. Pressing the ENTER button once more will confirm your setting. You may exit the main menu at any time without making any adjustments by pressing the MODE/ESC button.

LCD CONTROL PANEL LOCKOUT
When the Key Lock menu is set to ON, the LCD display will turn OFF after 30 seconds and the (4) button Control Panel will be LOCKED. To unlock the (4) button LCD control panel, press and hold the MODE button.

INFORMATION DISPLAYED DURING INITIAL POWER ON
When the fixture is initially powered ON, the display shows the following information: ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig7

SYSTEM MENU
Supports Software Version: ≥ V1.12
Features are subject to change without any prior written notice.
MAIN MENU SUB MENU OPTIONS / VALUES (Default Settings in BOLD) DESCRIPTION
Address Set DMX Address 001 ~ XXX DMX Address Setting
 

UserMode

Standard 18CH (16bit)  

Set DMX Channel Mode

Basic 16CH (8bit)
Extend 78CH
 

 

 

 

 

 

 

 

 

 

 

 

 

Function

 

 

Status

Lost DMX Close/Hold/Auto. Pro Function If NO DMX Detected
Tilt. Inv ON / OFF Tilt Reverse Movement
Feedback ON/OFF Movement Feedback
Move. Spd Speed 1 ~ 4 Movement Mode Select
Hibernat OFF, 01M~99M, 15M Hibernate Mode
Fan. Set* Head Fan Auto, High, Silent* Fan Speed Set
 

Net ID

Password Password=xxx Password=050
DeviceIP xxx.xxx.xxx.xxx  
Mark Addr xxx.xxx.xxx.xxx  
Universe 000-255  
Protocol ArtNet, SACN Set Network Protocol
KlingNet Enable / Disable Enable KlingNet Protocol
Net ON / OFF Activate NET OUT Port.
 

LCD. Set

Backlight 02~60m 05m LCD Backlight Shut Off Time
FlipDisplay ON / OFF Flip/Reverse LCD Display 180º
Key Lock ON / OFF Control Front Panel Buttons Key Lock
Flash ON / OFF Display flashes when NO DMX
Temp. C/F Fahrenheit/Celsius Temperature Switch Between F˚/ C˚
 

 

Disp. Set

ADDR TILT… Value of each Channel Displayed
Disp. CH    
Secondary Secondary 1, Secondary 2,

Secondary 3

Set Secondary Mode Preset
Auto.Pro Alone, Primary Set Auto Program Mode
DimCurve Standard, Stage, TV, Architectural, Theatre, Stage2, 0-10s (Default 0.1s) Set Dimmer Curve Mode
Frequen 900/1000/1100/1200/1300/1400/1500/2500/

4000/5000/10k/15k/20k/25k

 
Pixel Standard, Flip Set Pixel Flip Mode
DFSE ON / OFF Restore Factory Settings
 

 

 

 

Information

 

 

Time. Info

Current XXXX (Hours) Fixture Run Time From Power ON
Total XXXX (Hours) Fixture Total Run Time
Last XXXX (Hours) Clear Fixture Last Run Time
Password Clear/Clear-TO Password=050 Password to clear last fixture run time
Password=060 Password to clear total run time
ON / OFF Reset Fixture Last Run Time
TempInfo LED Temp. XXX / C° Temperature in Fixture Head
Err. Info Tilt….. Display 10 Recent Error Messages
ModelInfo Chorus Line 8 Display Model Name
Software Version 1U01 – 5U01 ≥V1.12 Software Versions
 

 

Test

Reset. M All  
Test. Ch Tilt …  
ManCtrl Tilt=XXXX

:

 
 

Calibrat

Password

Tilt, Red1, Green1, Blue1, White1…Red8, Green8, Blue8, White8, Zoom1, Zoom2

 

Password=050

DMX CHANNEL FUNCTIONS AND VALUES

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC CH: 16 STANDARD CH: 18 EXTEND CH: 78
 

1

 

1

 

1

  TILT Movement 8bit    
0-255 TILT Movement
   

2

 

2

  Tilt Fine 16bit    
0-255 Fine Control of TILT Movement
 

2

 

3

 

3

  Red    
0-255 0 → 100%
 

3

 

4

 

4

  Green    
0-255 0 → 100%
 

4

 

5

 

5

  Blue    
0-255 0 → 100%
 

5

 

6

 

6

  ALL AMBR    
0-255 0 → 100%
     

7

  Red 2    
0-255 0 → 100%
     

8

  Green 2    
0-255 0 → 100%
     

9

  Blue 2    
0-255 0 → 100%
     

10

  White 2    
0-255 0 → 100%
     

11

  Red 3    
0-255 0 → 100%
     

12

  Green 3    
0-255 0 → 100%
     

13

  Blue 3    
0-255 0 → 100%
     

14

  White 3    
0-255 0 → 100%
     

15

  Red 4    
0-255 0 → 100%
     

16

  Green 4    
0-255 0 → 100%
     

17

  Blue 4    
0-255 0 → 100%
     

18

  White 4    
0-255 0 → 100%
     

19

  Red 5    
0-255 0 → 100%
     

20

  Green 5    
0-255 0 → 100%
     

21

  Blue 5    
0-255 0 → 100%
     

22

  White 5    
0-255 0 → 100%

 

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC

CH: 16

STANDARD

CH: 18

EXTEND

CH: 78

    23   Red 6    
0-255 0 → 100%
     

24

  Green 6    
0-255 0 → 100%
    25   Blue 6    
0-255 0 → 100%
     

26

  White 6    
0-255 0 → 100%
    27   Red 7    
0-255 0 → 100%
     

28

  Green 7    
0-255 0 → 100%
    29   Blue 7    
0-255 0 → 100%
    30   White 7    
0-255 0 → 100%
    31   Red 8    
0-255 0 → 100%
    32   Green 8    
0-255 0 → 100%
    33   Blue 8    
0-255 0 → 100%
    34   White 8    
0-255 0 → 100%
    35   Red 9    
0-255 0 → 100%
    36   Green 9    
0-255 0 → 100%
    37   Blue 9    
0-255 0 → 100%
    38   White 9    
0-255 0 → 100%
     

39

  Red 10    
0-255 0 → 100%
     

40

  Green 10    
0-255 0 → 100%
     

41

  Blue 10    
0-255 0 → 100%
     

42

  White 10    
0-255 0 → 100%
 

 

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC

CH: 16

STANDARD

CH: 18

EXTEND

CH: 78

    43   Red 11    
0 – 255 0 → 100%
     

44

  Green 11    
0 – 255 0 → 100%
    45   Blue 11    
0 – 255 0 → 100%
     

46

  White 11    
0 – 255 0 → 100%
    47   Red 12    
0 – 255 0 → 100%
     

48

  Green 12    
0 – 255 0 → 100%
    49   Blue 12    
0 – 255 0 → 100%
    50   White 12    
0 – 255  
    51   Red 13    
0 – 255 0 → 100%
    52   Green 13    
0 – 255 0 → 100%
    53   Blue 13    
0 – 255 0 → 100%
    54   White 13    
0 – 255 0 → 100%
    55   Red 14    
0 – 255 0 → 100%
    56   Green 14    
0 – 255 0 → 100%
    57   Blue 14    
0 – 255 0 → 100%
    58   White 14    
0 – 255 0 → 100%
     

59

  Red 15    
0 – 255 0 → 100%
     

60

  Green 15    
0 – 255 0 → 100%
     

61

  Blue 15    
0 – 255 0 → 100%
     

62

  White 15    
0 – 255 0 → 100%
 

 

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC CH: 16 STANDARD CH: 18 EXTEND CH: 78
    63   Red 16    
0-255 0 → 100%
    64   Green 16    
0-255 0 → 100%
    65   Blue 16    
0-255 0 → 100%
    66   White 16    
0-255 0 → 100%
   

7

 

67

  CTO    
0-23 Open
24-255 CTO 2700K – 7000K    
6 8 68   Color Macros    
0-255 See Macro Chart
 

 

 

 

 

7

 

 

 

 

 

9

 

 

 

 

 

69

  Strobe    
0 – 31 Closed
32 – 63 Open
64 – 95 Strobe (slow → fast)
96 – 127 Open
129-159 Pulse (slow → fast)
160 – 191 Open
192 – 223 Random (slow → fast)
224 – 255 Open
8 10 70   Master Intensity    
0 – 255 Close → Open
9 11 71   Master Intensity Fine    
0 – 255 Close → Open
10 12 72   Zoom    
0-255 Zoom Min to Max
 

 

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

13

 

 

 

 

 

 

 

 

 

 

73

  Auto Programs    
0 Idle
1-14 Off
15-30 Program 1
31-46 Program 2
47-62 Program 3
63-78 Program 4
79-94 Program 5
95-110 Program 6
111-126 Program 7
127-142 Program 8
143-158 Program 9
159-174 Program 10
175-190 Program 11
191-206 Program 12
207-222 Program 13
223-238 Program 14
293-255 Program 15
 

 

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC

CH: 16

STANDARD

CH: 18

EXTEND

CH: 78

12 14 74   Program Speed 128  
0 – 255 Speed (slow → fast)
 

13

 

15

 

75

  Program Fade  

128

 
0 – 255 Fade (slow → fast)
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

76

  Dim Modes  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

0 – 20 Standard
21 – 40 Stage
41 – 60 TV
61- 80 Archictural
81- 100 Theatre
101- 120 Stage 2
  Dimmer Delay Time
121 0s
122 0.1s (default)
123 0.2s
124 0.3s
125 0.4s
126 0.5s
127 0.6s
128 0.7s
129 0.8s
130 0.9s
131 1.0s
132 1.5s
133 2.0s
134 3.0s
135 4.0s
136 5.0s
137 6.0s
138 7.0s
139 8.0s
140 9.0s
141 10s
142 – 255 Default
 

 

15

 

 

17

 

 

77

  Pan / Tilt Speed    
0-225 Max to min speed
226-235 Blackout by movement
236-255 No function
 

 

Supports Software Versions: ≥ V1.12
Features are subject to change without any prior written notice.

*Direction of effects and Pixel Control depends on orientation of the fixture head and Tilt/Pixel Flip settings.

MODE / CHANNEL VALUE FUNCTION DEFAULT SNAP
BASIC

CH: 16

STANDARD

CH: 18

EXTEND

CH: 78

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

78

  Control  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

0 -5 Idle
6-10 Reset
11-15 Fan Mode Auto
16-20 Fan Mode High
21-25 Fan Mode Silent
25-29 Program 1
30-34 Program 2
35-39 Program 3
40-44 Program 4
45-49 Program 5
50-54 Program 6
55-59 Program 7
60-64 Program 8
65-69 Program 9
70-74 Program 10
75-79 Program 11
80-100 Program 12
  Change Refresh Rate (Hz)
101 – 105 900
106 – 110 1000
111 – 115 1100
116 – 120 1200
121 – 125 1300
126 – 130 1400
131 – 135 1500
136 – 140 2500
141 – 145 4000
146 – 150 5000
151 – 155 10000
156 – 160 15000
161 – 165 20000
166 – 170 25000
171-200 Idle
  Dimmer Curves
201-210 Dimmer Curve Linear (default)
211-220 Dimmer Curve Square
221-230 Dimmer Curve Inverse Square
231-240 Dimmer Curve S-Curve
241-255 Idle
 

COLOR MACRO CHART

VALUES 1-4 DMX VALUES 53-56 DMX VALUES 105-108 DMX VALUES 157-160 DMX VALUES 209-212
Red= 80 Red= 255 Red= 255 Red= 234 Red= 0
Green= 255 Green= 93 Green= 138 Green= 139 Green= 83
Blue= 234 Blue= 182 Blue= 186 Blue= 171 Blue= 115
W= 80 W= 93 W= 138 W= 0 W= 0
DMX VALUES 5-8 DMX VALUES 57-60 DMX VALUES 109-112 DMX VALUES 161-164 DMX VALUES 213-216
Red= 80 Red= 255 Red= 255 Red= 224 Red= 0
Green= 255 Green= 96 Green= 147 Green= 5 Green= 97
Blue= 164 Blue= 236 Blue= 251 Blue= 97 Blue= 166
W= 80 W= 96 W= 147 W= 0 W= 0
DMX VALUES 9-12 DMX VALUES 61-64 DMX VALUES 113-116 DMX VALUES 165-168 DMX VALUES 217-220
Red= 77 Red= 238 Red= 151 Red= 175 Red= 1
Green= 255 Green= 93 Green= 138 Green= 77 Green= 100
Blue= 112 Blue= 255 Blue= 255 Blue= 173 Blue= 167
W= 77 W= 93 W= 138 W= 0 W= 0
DMX VALUES 13-16 DMX VALUES 65-68 DMX VALUES 117-120 DMX VALUES 169-172 DMX VALUES 221-224
Red= 117 Red= 196 Red= 151 Red= 119 Red= 0
Green= 255 Green= 87 Green= 138 Green= 130 Green= 40
Blue= 83 Blue= 255 Blue= 255 Blue= 199 Blue= 86
W= 83 W= 87 W= 138 W= 0 W= 0
DMX VALUES 17-20 DMX VALUES 69-72 DMX VALUES 121-124 DMX VALUES 173-176 DMX VALUES 225-228
Red= 160 Red= 150 Red= 138 Red= 147 Red= 209
Green= 255 Green= 90 Green= 169 Green= 164 Green= 219
Blue= 77 Blue= 255 Blue= 255 Blue= 212 Blue= 182
W= 77 W= 90 W= 138 W= 0 W= 0
DMX VALUES 21-24 DMX VALUES 73-76 DMX VALUES 125-128 DMX VALUES 177-180 DMX VALUES 229-232
Red= 223 Red= 100 Red= 255 Red= 88 Red= 42
Green= 255 Green= 77 Green= 255 Green= 2 Green= 165
Blue= 83 Blue= 255 Blue= 255 Blue= 163 Blue= 85
W= 83 W= 77 W= 255 W= 0 W= 0
DMX VALUES 25-28 DMX VALUES 77-80 DMX VALUES 129-132 DMX VALUES 181-184 DMX VALUES 233-236
Red= 255 Red= 77 Red= 255 Red= 0 Red= 0
Green= 243 Green= 100 Green= 206 Green= 38 Green= 46
Blue= 77 Blue= 255 Blue= 143 Blue= 86 Blue= 35
W= 77 W= 77 W= 0 W= 0 W= 0
DMX VALUES 29-32 DMX VALUES 81-84 DMX VALUES 133-136 DMX VALUES 185-188 DMX VALUES 237-240
Red= 255 Red= 67 Red= 254 Red= 0 Red= 8
Green= 200 Green= 148 Green= 177 Green= 142 Green= 107
Blue= 74 Blue= 255 Blue= 153 Blue= 208 Blue= 222
W= 74 W= 67 W= 0 W= 0 W= 0
DMX VALUES 33-36 DMX VALUES 85-88 DMX VALUES 137-140 DMX VALUES 189-192 DMX VALUES 241-244
Red= 255 Red= 77 Red= 254 Red= 52 Red= 107
Green= 166 Green= 195 Green= 192 Green= 148 Green= 156
Blue= 77 Blue= 255 Blue= 138 Blue= 209 Blue= 231
W= 77 W= 77 W= 0 W= 0 W= 0
DMX VALUES 37-40 DMX VALUES 89-92 DMX VALUES 141-144 DMX VALUES 193-196 DMX VALUES 245-248
Red= 255 Red= 77 Red= 254 Red= 1 Red= 165
Green= 125 Green= 234 Green= 165 Green= 134 Green= 198
Blue= 74 Blue= 255 Blue= 98 Blue= 201 Blue= 247
W= 74 W= 77 W= 0 W= 0 W= 0
DMX VALUES 41-44 DMX VALUES 93-96 DMX VALUES 145-148 DMX VALUES 197-200 DMX VALUES 249-252
Red= 255 Red= 158 Red= 254 Red= 0 Red= 0
Green= 97 Green= 255 Green= 121 Green= 145 Green= 0
Blue= 77 Blue= 144 Blue= 0 Blue= 212 Blue= 255
W= 74 W= 144 W= 0 W= 0 W= 0
DMX VALUES 45-48 DMX VALUES 97-100 DMX VALUES 149-152 DMX VALUES 201-204 DMX VALUES 253-255
Red= 255 Red= 255 Red= 176 Red= 255 Red= 0
Green= 71 Green= 251 Green= 17 Green= 0 Green= 0
Blue= 77 Blue= 153 Blue= 0 Blue= 0 Blue= 0
W= 71 W= 153 W= 0 W= 0 W= 255
DMX VALUES 49-52 DMX VALUES 101-104 DMX VALUES 153-156 DMX VALUES 205-208  
Red= 255 Red= 255 Red= 96 Red= 0    
Green= 83 Green= 175 Green= 0 Green= 255
Blue= 134 Blue= 147 Blue= 11 Blue= 0
W= 83 W= 147 W= 0 W= 0

PI XEL CONTROL

The starting pixel position can be flipped to the opposite side of the fixture by selecting FLIP mode in the FUNCTION / PIXEL sub menu from the control panel.
The fixture features full pixel control in Extended DMX channel mode.
Diagram below illustrates the specific pixel mapping order for both modes.

ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig8

TECHNICAL SPECIFICATIONS

SOURCE

  • (16) 40W 4-in-1 RGBW LEDs
  • 50,000 Hour Average LED Life*
  • May vary depending on several factors including but not limited to: Environmental Conditions, Power/Voltage, Usage Patterns (On-Off Cycling), Control and Dimming.

PHOTOMETRIC DATA

  • 5,700+ Total Lumens
  • 20,478 LUX 1903 FC @16.4 ft (5m) (Full ON (4° Min Zoom)
  • 570 LUX 53 FC @16.4 ft (5m) (Full ON (37° Max Zoom)
  • Zoom Range 4° – 40°
  • Beam Angle 4.6° – 37.8°
  • Field Angle 7.8° – 54.4°

EFFECTS

  • Motorized Zoom and 220° Tilt Movement
  • RGBW Color Mixing and Full Pixel Control
  • 2,700K – 7,000K Linear Color Temperature Range
  • 64 Color Presets and 14 Unique Color Macros
  • Electronic Strobe, 16-bit Variable Dimming Curve Modes

COLOR
RGBW

CONTROL / CONNECTIONS

  • 3 DMX Channel Modes (78 total channels)
  • DMX, RDM, Kling-Net, and Art-Net Protocol Support
  • Adjustable LED Refresh Rate (900-25,000 Hz)
  • Adjustable LED Gamma Brightness (2.0, 2.2, 2.4, 2.8)
  • 4 Button Touch Control Panel
  • 180° Reversible LCD Menu Display
  • 8 / 16-Bit Resolution Zoom and Tilt Movement
  • 5pin DMX In/Out
  • RJ45 Ethernet In/Out
  • Locking Power Cable In/Out
  • With Wired Digital Communication Network

SIZE / WEIGHT

  • Length: 42.05″ 1068mm)
  • Width: 7.44″ (189mm)
  • Vertical Height: 11.46″ (291mm)
  • Weight: 47.0 lbs (21.3 kg)

ELECTRICAL / THERMAL

  • AC 100-240V – 50/60Hz
  • 739W Max Power Consumption
  • 5°F to 113°F (-15°C to 45°C)
  • BTU/hr (+/- 10%) 2519.99
  • APPROVALS / RATINGS
DIMENSIONAL DRAWINGS ELATION-PROFESSIONAL-CHORUS-LINE-16-RGBW-LED-Bar-fig9

Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

OPTIONAL ACCESSORIES

ORDER CODE ITEM
DRCCL16 9-Pack Road Case for Chorus Line 16
NARROW CLAMP Heavy Duty Wrap Around Hook Style Clamp
SCABLE 60 60 lbs. Rating 24 Inch Safety Cable
AC5PDMX5PRO 5 ft. (1.5m) 5pin PRO DMX Cable
PLC3 3 ft. (1m) PRO Link Cable
  Additional Cable Lengths Available

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

  •  Reorient or relocate the device.
  •  Increase the separation between the device and the receiver.
  •  Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.
  •  Consult the dealer or an experienced radio/TV technician for help.

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the environment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you

Documents / Resources

ELATION PROFESSIONAL CHORUS LINE 16 RGBW LED Bar [pdf] User Manual
CHORUS LINE 16, RGBW LED Bar, CHORUS LINE 16 RGBW LED Bar

Leave a comment

Your email address will not be published.