EJEAS EUC Controller Motorcycle Bluetooth Handlebar

Product Information

Specifications:

• Product Name: MESH Intercom Expert FM
• Brand: EJEAS
• Model: EUC

Product Usage Instructions

EUC Controller Pairing Operation Guide

EUC Remote Controller Buttons Introduction
Below are the actions and functions associated with each button on the EUC remote controller:

EUC Pairing
To pair the EUC, follow these steps:

1. Press and hold the + button for about 5 seconds to enter pairing mode.
2. If pairing is not successful within 2 minutes, exit the pairing.

EUC Handle Operation
Mesh intercom reconnect/disconnect and mobile phone control are the same as on the machine.

Bluetooth Intercom Connection
To initiate a Bluetooth intercom connection, follow these steps:

1. Initiate Bluetooth Intercom Connection by pressing the corresponding button.
2. To disconnect the intercom, long-press the appropriate button.

FM On/Off
To turn FM on/off, press the FM Button for 1 second.

Frequently Asked Questions:

• Q: How do I pair the EUC remote controller?
  A: Press and hold the + button for about 5 seconds to enter pairing mode. Follow the voice prompts for successful pairing.
• Q: How do I initiate a Bluetooth intercom connection?
  A: Press the corresponding button to initiate a Bluetooth intercom connection. Long-press to disconnect the intercom.

Q8 EUC

EUC Remote Controller (Optional)

Buttons Introduction

EUC Pairing

1. Press and hold the <Phone/Power Button> + <Volume -> for about 5s to enter the pairing mode, the voice prompts “Remote Control Pairing”, and the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flash alternately
   • “Remote Control Pairing”
2. Press and hold the < FM Button >+ < Volume – > on the handle for about 5s to clear the record until the red and blue lights come on.
   • Until the red and blue lights come on
3. Click any button on EUC

Pairing Successful ‘Paimg Successful’
(No successful pairing within 2 minutes, exit the pairing)

EUC Handle Operation
Mesh intercom reconnect/disconnect and mobile phone control are the same as on the machine.

K1 EUC

EUC Remote Controller (Optional)

Buttons Introduction

EUC Pairing

1. Press and hold the <Phone/Power Button> + <Volume -> for about 5s to enter the pairing mode, the voice prompts “Remote Control Pairing”, and the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flash alternately
   • “Remote Control Paiing”
2. Press and hold the < FM Button >+ < Volume – > on the handle for about 5s to clear the record until the red and blue lights come on.
   • Until the red and blue lights come on
3. Click any button on EUC

Click any button of EUC “Pairing SucoessfUI”
(No successful pairing within 2 minutes, exit the pairing）

EUC Handle Operation
Mesh intercom reconnect/disconnect and mobile phone control are the same as on the machine.

MS20 EUC

EUC Remote Controller (Optional)

Buttons Introduction

Restore Default Settings
Press and hold <Phone/Power Button> + <Volume +> + <Volume -> for about 5s, the voice prompts “Restore Default Settings” to delete the pairing record, and then automatically reboots the phone.

• “Restore Default Settings”

Firmware Upgrades

Connect to the computer with a USB data cable. Download and open the “EJEAS Upgrade.exe” upgrade software. Click on the “Upgrade” button to start and wait for the upgrade to complete.

MS8 EUC

Handle EUC (optional)

Key Descriptions

EUC Pairing

1. Press and hold the <Phone/Power button> + <Volume -> for about 5s to enter the pairing mode, the voice prompts “Remote Control Pairing”, and the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flashing alternately
   • “Remote Control Pairing”
2. Press and hold the FM+Volume – button on the handle for about 5s to clear the record until the red and blue lights come on.
   • Until the red and blue lights come on
3. EUC Click any key.

Pairing Successful “Pairing Successful”
(No successful pairing within 2 minutes, exit the pairing)

Handle Operation
Mesh intercom reconnect/disconnect and mobile phone control are the same as on the machine.

E1 Pro+ EUC

EUC Remote Controller (Optional)

Buttons Introduction

EUC Pairing 

1. Long press both <Button FM> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Long press both<Phone Button> and <Volume-> for 5s to enter the handle pairing mode,the red and blue lights flash alternately and quickly.
   • Red light and blue light are on at the same time
3. Click any button of EUC

Pairing Successfully “Pairing Successful”
(If EUC cannot be successfully paired in 2 mins, it will automatically exit the pairing mode.)

Firmware Upgrades

Connect to the computer with a USB data cable, then download and open the “EJEAS Upgrade . exe” to upgrade software. Click the “Upgrade” button to start and wait for the upgrade to complete.

E1 Pro EUC

EUC Remote Controller (Optional)

Buttons Introduction

EUC Pairing 

1. Long press both <Button FM> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Long press both<Phone Button> and <Volume-> for 5s to enter the handle pairing mode, the red and blue lights flash alternately and quickly.
   • Red light and blue light are on at the same time
3. Click any button on EUC

Pairing Successfully “Pairing Successful”
If EUC cannot be successfully paired in 2 minutes, it will automatically exit the pairing mode.

Firmware Upgrades

Connect to the computer with a USB data cable, then download and open the “EJEAS Upgrade . exe” to upgrade software. Click the “Upgrade” button to start and wait for the upgrade to complete.

MS8SE EUC

EUC Remote Controller (Optional)

Buttons Introduction

EUC Pairing

1. Press and hold the <Phone/Power Button> + <Volume -> for about 5s to enter the pairing mode, the voice prompts “Remote Control Pairing”, and the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flash alternately
   • “Remote Control Pairing”
2. Press and hold the < FM Button >+ < Volume – > on the handle for about 5s to clear the record until the red and blue lights come on.
   • Until the red and blue lights come on
3. Click any button on EUC

Pairing Successful “Pairing Successful”
No successful pairing within 2 minutes, exit the pairing

EUC Handle Operation
Mesh intercom reconnect/disconnect and mobile phone control are the same as on the machine.

V4Plus EUC

Frequency Switching

EUC Remote Control (Optional)

EUC Details

EUC Pairing

1. Long press both <FM Button> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red and Blue lights consistently on
2. Long press both <Phone Button> and <B Button> of V4 Plus for 5s.
   • Red and blue lights flash alternately and quickly
   • “Remote Control Pairing”
3. Click any key of EUC.

Pairing Successfully “Pairing Successful”
(If EUC cannot be successfully paired in 2 mins, It will automatically exit the pairing mode.)

V6/V6Pro EUC

EUC Remote Controller (Optional)
Buttons Introduction

EUC Pairing

1. Long press both <Button FM> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Long press both<Phone Button> and <Button E> for 5s to enter the handle pairing mode, the red and blue lights flash alternately and quickly.
   • Red light and blue light are on at the same time
3. Click any button on EUC

Pairing Successfully “Du, Du”
If EUC cannot be successfully paired in 2 minutes, it will automatically exit the pairing mode.

Restore Default Settings

• Press and hold both <B button> and <Phone button> for about 2s, the red light flashes 3 times quickly to delete the pairing record, and then the intercom will automatically power on again.
• 3 Quick Flashes
• “Di,Di,Di”

V6PRO+ EUC

EUC Remote Controller (Optional)
Buttons Introduction

EUC Pairing 

1. Long press both <Button FM> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Long press both<Phone Button> and <Button E> for 5s to enter the handle pairing mode,the red and blue lights flash alternately and quickly.
   • Red light and blue light are on at the same time
3. Click any button of EUC

Pairing Successfully “Du”
If EUC cannot be successfully paired in 2 minutes, it will automatically exit the pairing mode.

Restore Default Settings
Press and hold both <B button> and <Phone button> for about 2s, the red light flashes 3 times quickly to delete the pairing record, and then the intercom will automatically power on again.

• 3 Quick Flashes
• “Di,Di,Di”

V7 EUC

EUC pairing

1. Long press both <FM Button> and <Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Press and hold <phone button> + <E Button> for about 5s to enter the pairing mode, the voice prompts “ding ding ding”, the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flashing alternately
   • “Di, Di, Di”
3. Click any button of EUC

Pairing Successfully “Pairing Successful”
(If EUC cannot be successful paired in 2 mins, it will automatically exit the pairing mode.)

Firmware upgrades

Connect the product to the PC using USB. Download and open the “EJEAS Upgrade.exe” upgrade software. Click on the “Upgrade” button to start the upgrade and wait for the upgrade to complete.

Restore Default Settings

Press and hold ‹Phone button> + <B button > for about 2s, the red light flashes 3 times quickly to delete the pairing record, and then the intercom will automatically power on again.

EUC pairing

1. Long press both ‹FM Button> and ‹Volume -> of EUC for 5s to clear the pairing record of EUC.
   • Red light and blue light are on at the same time
2. Press and hold <phone button> + <E Button > for about 5s to enter the pairing mode, the voice prompts “ding ding ding”, and the red and blue lights flash alternately, if the pairing is not successful within 2 minutes, exit the pairing.
   • Red light and blue light flashing alternately
   • “Di, Di, Di”
3. Click any button on EUC

Pairing Successfully “Pairing Successful”
(If EUC cannot be successfully paired in 2 mins, it will automatically exit the pairing mode.)

Firmware upgrades

Connect the product to the PC using USB. Download and open the “EJEAS Upgrade.exe” upgrade software. Click on the “Upgrade” button to start the upgrade and wait for the upgrade to complete.

Restore Default Settings

Press and hold ‹Phone button> + <B button> for about 2s, the red light flashes 3 times quickly to delete the pairing record, and then the intercom will automatically power on again.

Q7 EUC

Documents / Resources

EJEAS EUC Controller Motorcycle Bluetooth Handlebar [pdf] User Guide Q8, MS8, MS8SE, V6PRO, K1, E1 Pro, V4Plus, V7, MS20, E1 Pro, V6-V6Pro, Q7, EUC Controller Motorcycle Bluetooth Handlebar, EUC, Controller Motorcycle Bluetooth Handlebar, Motorcycle Bluetooth Handlebar, Bluetooth Handlebar, Handlebar

References

• User Manual