Effon M2 Barcode Reader User Guide

Effon M2 Barcode Reader

Specifications

Setup & Use

1. Power on: Press either side button to turn on the device.
2. Power off: By default it shuts down after 5 minutes of sleep. To change shutdown behavior, scan the sleep-time setup barcode (or scan the Sleep now barcode).
3. Initialize/reset: Scan the Initialize Settings barcode to reset to initial settings.
4. Update version display: Scan the Display version information barcode to show version details.
5. Set output customization (optional): Use the relevant setup barcodes for prefix/suffix, end character, HID character case, and hide front/rear characters.
6. Configure Bluetooth (optional): After connecting Bluetooth, scan Change Bluetooth Name, then scan the desired Bluetooth name barcode; after canceling Bluetooth pairing, search again. To switch modes, scan the required Bluetooth mode barcode.
7. Mounting (optional): Adhere the metal plate to your phone/case, align the M2 slots to the plate, and slide upward until it clicks; to remove, hold the sliding button and slide the scanner downward.

Turn on & Turn off

Turn On:
Press either side button to turn on the device.

Turn Off:
By default, it will shut down after 5minutesofsleep.You can scan the setting code to turn off, or set the required sleep time.

Initialization settings &Versioninformation
To reset the scanner to its initial settings, scanthe“InitializeSettings” barcode below. Scanning the “DisplayVersionInformation” barcode will show the scanner’s versiondetails.

Prefix and suffix setting
Scan the “Prefix setting” or “Suffix setting” barcode, then scan the ADCII code of the desired prefix or suffix character.

Transmission speed setting

Sleep time setting

Storage mode setting

Set to hide front or rear characters
Scan the “Hide front character” or “Hide rear character” setup code first, then scan the barcode with the desired number of characters.

HID output character casesetting

HID keyboard language setting

Change Bluetooth name

• Step1: After connecting Bluetooth, scan the “Change Bluetooth Name” barcode.
• Step2: Scan the barcode for the Bluetooth name you wish to set, such as “Scanner123”. Finally, after canceling the Bluetooth pairing, perform a new Search to find the new Bluetooth name

Bluetooth mode setting
After scanning the required Bluetooth mode barcode, thescanner will switch to the corresponding mode.

End character setting

Volume and motor setting

Toggle Bluetooth HIDkeyboardiniOS

Display battery level

Mounting

1. Attach: Adhere the metal plate with fixing hooks to the back of your phone or phone case.
2. Align: Position the M2 scanner, aligning its slots with both ends of the metal plate.
3. Slide & Lock: Slide the M2 upward until you hear a “click,” indicating it is securely locked in place.

Dismounting

1. Unlock: Push the sliding button at the bottom of the M2 to the left and hold it in position.
2. Slide Off: While holding the button, slide the M2 downward to remove it from the plate.

Tip:
The metal plate on your phone allows for quick and easy Reinstallation whenever needed.

Dimensions 
90.3×62.4X14.O mm (LXWXH)

Weight :
49.5grams

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Troubleshooting

• Scanner output not as expected (prefix/suffix, hidden characters, end character): Re-check the relevant setup codes and use the corresponding cancel procedure (e.g., scan the Prefix/Suffix setting barcode again to cancel, or scan the Cancel end character barcode).
• Need to restore default settings: Scan the Initialize Settings barcode to reset the scanner to its initial settings.
• Bluetooth device name change didn’t take effect: The manual states that after initialization the Bluetooth name reverts to default. Also, after setting a new name, cancel Bluetooth pairing and perform a new search to find the updated Bluetooth name.
• Need to switch Bluetooth behavior: Scan the desired Bluetooth Mode Setting barcode; the scanner will switch to the corresponding mode.
• Power/sleep timing confusion: If the device is shutting down sooner than desired, scan the appropriate Sleep Time Setting barcode (e.g., 10 minutes, 30 minutes, or Never sleep).