EDUPLINK M6 Pro Portable Waterproof Wireless Speaker Instructions
EDUPLINK M6 Pro Portable Waterproof Wireless Speaker

Dear Sir/Madam,
Hope you are well, Wonderful Sound that Will Immediately Brighten Up Your Day.
If you have any words to say about the bluetooth speaker, please don’t hesitateemail and email us via,
[email protected] or
[email protected]
Kind regards


  1. Power Button Press and hold the button to switch on or off. Click to play or pause.
  2. Wireless / Phone Call Click the button to (1) switch between Wireless and AUX modes or (2) answer/hang up calls. Press and hold the button to disconnect the Wireless connection.
  3. +” Button Click to increase volume. Press and hold the button for next track.
  4. ” Button Click to decrease volume. Press and hold the button for previous track.
  5. TWS Pairing Button Press and hold start or cancel TWS interconnection. Click to turn on or off party lights.
  6. Type-c charging port
  7. TF card slot
  8. External Audio Connection


  • Product Model: M6 Pro
  • Wireless Version: 5.0
  • Wireless Transmission Distance: >10M
  • Impedance:
  • Sensitivity: 1000mv
  • Frequency Response Range: 601-Iz-20KHZ
  • Speaker: 45mm internal magnetic: 4010W
  • Output Power: 2*10W
  • Battery: 3600mAh 3.7V
  • Charging Voltage: 5V-1A
  • Product Dimensions: 160mm*79mm*79mm
  • Product Weight: 452g
  • Standby Time: 90 days
  • Play Time: 8 hrs
  • Supported Features: Wireless, audio input, TF car
  • Distortion: 1%
  • Signal To Noise Ratio: 70dB
  • Waterproof Rating: IPX7


Switching On/Off
Press and hold the power button for 2 seconds to switch on; one more time to switch off.

Wireless Connection
Once the product is switched on, it enters wireless mode and the power Buttons button begins to flash. Turn on your wireless device, searching for ” M6 Pro “, and pair with it If they are connected successfully, you will a hear prompt tone. If the power button stops flashing and stays on, you can play music on your device through the speaker.

TWS True Wireless Stereo Playback
Switch on two M6 Pro speakers, entering Wireless mode. Click the button 0 on one of the speakers, White lights flickered alternately, and the speaker will automatically search for the other speaker.
to connect. After the connection is successful, the two speakers will automatically convert into left and right channels. Repeat the wireless connection steps to connect the speakers with your device. After the connection is successful, the two speakers can play music and deliver stereo sound.


  1. This function requires two M6 Pro speakers, switching them on.
  2. Speakers do not have wireless connection with any device before TWS pairing.
  3. When the TWS is connected, long press the Buttons button of one of the products to cancel the connection.

AUX Audio Input
Connect a 3.5mm audio cable to your phone’s/computer’s headphone output port, switch the speaker to AUX input mode, and now you can control music on your phone or computer.

TF / Micro SD Audio Input
The speaker is compatible with TF/Micro SD cards of up to 32GB in size and can play MP3 and WMA audio files directly. Simply insert a compatible card into the slot underneath the speaker and the unit will automatically switch to TF mode and Automatically play the music in the card. You can use the media controls on the front of the unit to play, pause and navigate between tracks on the card.


This product is not sale with adapter, Please buy accessory package together with power adapter that has been certificated by 3C and meet safety requirements.

  1. When you hear the voice prompt “out of battery”, charge the speaker as soon as possible.
  2. It takes 4-5 hours to get fully charged.
  3. The power lamp breathes when charging and lights long after filling.


  1. Turn off the speaker during storage and be sure it is properly protected.
  2. Avoid high temperatures ( above 40 °C ), such as high temperature cabins or being exposed to direct sunlight ( high temperatures will damage the exterior and decrease battery life).
  3. Do not expose speakers or other parts to rain or liquids.


This product is covered under warranty for a period of one year from the date of sale limited to normal use and maintenance of the machine parts, materials and functions. Problems and failures verified upon further identification will be provided free repair and replacement parts.

This warranty does not apply:

  1. to a product that is out of warranty;
  2. The speaker is damaged and the shell is damaged if the user does not comply with the instructions;
  3. to a product that has been disassembled, repaired or modified without the authorization of REMAX;
  4. if warranty card and proof of purchase cannot be presented;
  5. to damage caused by earthquake, fire or other external causes, natural disasters, etc.

Note: The warranty does not include product transport costs and does not provide on-site maintenance services.


  1. No sound
  2. Sound quality deteriorates
  3. Button mal-function
  4. Unable to pair other devices
  5. Can not be recharged F. others

Buying time: _______________________________________

Dealers of sale: _____________________________________

Time of problems: __________________________________

User’ s contact info: _________________________________


Please scan qr and email to us .

qr code
[email protected]

qr code
[email protected]



Documents / Resources

EDUPLINK M6 Pro Portable Waterproof Wireless Speaker [pdf] Instructions
M6 Pro, Portable Waterproof Wireless Speaker, M6 Pro Portable Waterproof Wireless Speaker, Wireless Speaker, Waterproof Speaker, Waterproof Wireless Speaker, Portable Speaker, Portable Waterproof Speaker, Wireless Speaker Waterproof

Join the Conversation

1 Comment

  1. Warm Tip,
    Some Customers email us that the M6Pro Speaker can not pair to the phone, the reason is”Switch between Buetooth Pairing Mode & Aux-in Mode by “Phone” Button”

    Key Point:

    power button light is blinking—-Bluetooth Pairing Mode (Now link your mobile device with t Bluetooth Speaker )

    power button light is solid—–AUX in Mode(M6pro cant link with the phone)

    Press the “Call” button (located next to the power button) to switch from AUX-IN mode to Bluetooth Pairing Mode.

Leave a comment

Your email address will not be published.