DBWIFIBLE06 WIFI Module
“
Product Specifications
- Model: DBWIFIBLE06, DBWIFIBLE07
- Product Name: Hyperion PCBA
- Standard: 802.11 a/b/g/n
- Interface: USB/SDIO
- Modulation Method: GFSK(BLE), DQPSK, DBPSK,
CCK with DSSS(802.11b), QPSK, BPSK, 16QAM, 64QAM with OFDM
(802.11g/n/a) - Frequency Band: BLE 2402-2480 MHz
- Operation Mode: SISO
- Operating Voltage: Not specified
- Antenna Type: PIFA Antenna
- Operating Temperature: Not specified
- Storage Temperature: Not specified
- Humidity: 5 to 90% maximum
(non-condensing)
Product Usage Instructions
Installation
- Ensure the product is kept away from children’s reach.
- Avoid splashing water or liquids on the product.
- Avoid placing the product near heat sources or direct
sunlight.
Maintenance and Safety
- Avoid placing the product near flammable objects or naked
flames. - Do not attempt to repair the product yourself; seek assistance
from qualified personnel.
FCC Guidelines
- The FCC identification number should be visible when installed
inside another device. - If the module is installed inside another device, the exterior
of that device must display a label referring to the enclosed
module.
Frequently Asked Questions (FAQ)
Q: Can the antenna on the product be replaced?
A: No, the antenna is permanently attached and cannot be
replaced.
Q: What operating systems are compatible with this
product?
A: This product is compatible with Linux and Windows operating
systems.
Q: What encryption standard does this product support?
A: The product is capable of up to 128-Bit WEP Encryption.
“`
Hyperion PCBA IEEE 802.11 a/b/g/n 1T/1R Model Number: DBWIFIBLE06, DBWIFIBLE07
Product Descrition
The DBWIFIBLE06 is a complete 2.4GHz/5GHz WIFI module. This WIFI Module complied with IEEE 802.11 a/b/g/n standard and supports SISO mode. It has 1 PIFA antenna to WIFI and BT. Support 20MHz/40MHz in 5GHz band, and 20MHz in 2.4GHz band.
Product Features
Complies with IEEE 802.11b/g/n for 2.4GHzIEEE 802.11a/n for 5GHz Bluetooth v5.0 One transmit and One receive path(1T1R) Works with all existing network nfrastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. Operating SystemsLinux, Windows. Low power consumption. Easy to install and configure. SDIO interface. ROHS compliant
Product Specification
Model
DBWIFIBLE06, DBWIFIBLE07
Product Name Standard Interface Modulation Method
Frequency Band
Hyperion PCBA
802.11 a/b/g/n
USB/SDIO
GFSK(BLE) DQPSK,DBPSK,CCK with DSSS(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a)
BLE 2402~2480 MHz
Operation Mode Operating Voltage Antenna Type Operating Temperature Storage Temperature
WIFI 2.4G: 2412~2462 MHz 5G: 5180~5320MHz, 5500~5720MHz5745~5825MHz Infrastructure Module Voltage is 20V, supply 3.3V for IC. PCB antenna 0 ~ 60°C ambient temperature
-40 ~ 80°C ambient temperature
Humidity
5 to 90 % maximum (non-condensing)
PAGE 1 OF 6
Version 1.0
NOTICE:
please keep this product and accessories attached to the places which children can’t touch; do not splash water or other liquid onto this product, otherwise it may cause damage; do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation or malfunction; please keep this product away from flammable or naked flame; please do not repair this product by yourself. Only qualified personnel can be repaired.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2.2 This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
2.3 This radio transmitter FCC ID: QVHDBWIFIBLE06 has been approved by Federal Communications Commission to operate with the integrated PCB antenna. Use of any other antenna is strictly prohibited without filing an application for a new system-specific FCC ID. 2.4 The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval. 2.5 Trace antenna designs: Not applicable the antenna is integrated into the module and cannot be modified. See section 2.3. 2.6 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.7 Antenna type and antenna gain:
PAGE 2 OF 6
Version 1.0
BLE Antenna: Antenna 1
Frequency (MHz) 2402-2480
Antenna Type PCB Antenna
MAX Antenna Gain (dBi) 4.04
2.4G WIFI Antennas: Antenna 1
Frequency (MHz) 2412-2462
Antenna Type PCB antenna
MAX Antenna Gain (dBi) 4.04
5G WIFI Antennas: Antenna No.
Frequency Band
Antenna Type
1
5150-5850
PCB antenna
Note: The antenna is permanently attached and can’t be replaced.
Max Antenna Gain (dBi) 4.38
2.8
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as “Contains FCC ID: QVHDBWIFIBLE06”; any similar wording that expresses the same meaning may be used.
2.9 Testing of the host product with all the transmitters installed referred to as the composite investigation test- is recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually. If the modular transmitter has been fully tested by the module grantee on the required number of channels, modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration.
2.10 Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, part 15 E 15.407,15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, part 15 E 15.407,15B class B requirement. Then the host can be sold legally. The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
PAGE 3 OF 6
Version 1.0
2.11 The host manufacture is recommended to use FCC KDB 996369 D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.
2.12
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 7986A-DBWIFIBLE06” any similar wording that expresses the same meaning may be used.
l’appareil hôte doit porter une étiquette donnant le numéro de certification du module d’Industrie Canada, précédé des mots « Contient un module d’émission », du mot « IC: 7986A-DBWIFIBLE06» ou d’une formulation similaire exprimant le même sens, comme suit
the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour uneutilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 etla conformité à l’exposition de RSS-102 RF, utilisateurs peut obtenir l’information canadienne surl’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne
PAGE 4 OF 6
Version 1.0
ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
Antenna type and antenna gain: BLE Antenna:
Antenna
Frequency (MHz)
1
2402-2480
Antenna Type PCB Antenna
MAX Antenna Gain (dBi) 4.04
2.4G WIFI Antennas: Antenna 1
Frequency (MHz) 2412-2462
Antenna Type PCB antenna
MAX Antenna Gain (dBi) 4.04
5G WIFI Antennas: Antenna No.
Frequency Band
Antenna Type
1
5150-5850
PCB antenna
Note: The antenna is permanently attached and can’t be replaced.
Max Antenna Gain (dBi) 4.38
Notice to OEM integrator
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/Canada statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.
The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: QVHDBWIFIBLE06 or IC: 7986A-DBWIFIBLE06
Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.
Installer should put it in the manual The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
l’hôte doit utiliser l’instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d’exposition rf
mobile, ce qui signifie le dispositif est installé et utilisé à une distance d’au moins 20 cm de personnes.
le manuel de l’utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à
l’émetteur que de montrer dans ce manuel.
le fabricant est responsable de la conformité de l’hôte, le système d’accueil avec le module installé avec toutes
PAGE 5 OF 6
Version 1.0
les autres exigences applicables du système comme la partie 15 b, ices – 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l’hôte.
le dispositif d’accueil doivent avoir une étiquette indiquant contient FCC ID: QVHDBWIFIBLE06, IC: 7986A-DBWIFIBLE06 Les personnes chargées de l’installation devraient figurer dans le manuel: Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Doit avoir sur l’appareil hôte une étiquette indiquant Contient l’ID FCC QVHDBWIFIBLE06 ou IC : 7986A-DBWIFIBLE06 L’ID FCC et l’ID IC ne doivent pas être placés sur l’hôte en même temps et seuls les hôtes se rendant aux États-Unis peuvent utiliser l’ID FCC et seuls les hôtes se rendant au Canada peuvent utiliser l’ID IC.
PAGE 6 OF 6
Version 1.0
Documents / Resources
 | dyson DBWIFIBLE06 WIFI Module [pdf] User Guide DBWIFIBLE06, DBWIFIBLE07, DBWIFIBLE06 WIFI Module, DBWIFIBLE06, WIFI Module, Module |