duplex RCPS10 2.4EX RC Power Switch
Description and functions
- RCSwitch is a wireless switch designed especially for JETI model products (BEC stabilizers, Central Box and other accessories) that increase the comfort of model control.
- RCSwitch operation and setting isdone using a JETI Model DC/DS transmitter only.
Pairing
Pairing is done similarly to the pairing of receivers using the Bind Plug.
Procedure for pairing:
- Connect the Bind Plug to the EXT output.
- Connect the power supply to the Control Output.
- Select “pairing” in the RCSwitch menu in the JETI transmitter.
- Select a control for the RCSwitch in the transmitter, select the polarity of the switch, then also assign the audio sequence.
Switching is indicated by a red LED that is visible through the opening on the side of the RCSwitch. Setting the polarity of the switch is specific for each JETI model product. In the chart below, there is a list of several supported devices and their RCSwitch settings for DC and DS transmitters.
DEVICE Inverted polarity of the switch
- DPS 40 ✘
- SPS 20 ✘
- DSM 10 ✘
- Central Box 200 ✘
- Central Box 400 ✘
- Main Switch ✘
Connection
In normal mode the Ext slot is not used for output. It is used for pairing, for software updates and for connecting the JETIBOX terminal. How ever it is possible to supply power to both the RC Switch and the RC Power Switch through the Ext. or Control Output slots.
RCSwitch
Switched output is a signal line.
RCPowerSwitch(RCPS5, RCPS10)
- The power supply is connected via a two-wire cable. The positive pole is switched, the negative pole is common.
- For switching on constant currents lower than 5A, use the RC PowerSwitch5.
- For switching on constant currents lower than 10A, be sure to use the RCPowerSwitch10.
The maximum switching current must not be exceeded, see chapter „3. Technical data”.
Update
The RC Switch allows updating the firmware via PC. Updating is done using the Jeti USB adapter.
Procedure:
- Find the program to update to the latest firmware on the manufacturer’s website under “Downloads”. Save it to your computer.
- Connect the USB adapter to your computer. The procedure of installing the drivers for the USB adapter is included in the USB adapter manual.
- Run thefirmwareupdateon your PC.
- Connect the USB adapter to the RCSwitch (Ext. output) using a three-wire cable.
- Přehodit pořádek slov: After connecting the devic,e the update will begin.
Connection examples
Technical data
Connecting the RC Switch
to JETI model products
For a device that allows connecting the switch via JR JR-type connector, you can connect the RC Switch directly. For others that come with a standard magnetic switch without JR connector, you must interrupt the three-wire magnetic switch cable and solder in an RC Switch. To connect devices that do not allow direct connection of the RC Switch, we recommend installation in a professional workshop.
When connecting wires is necessary to keep their color code (brown wire connected to the brown wire, etc.)!
Warranty
Warranty, service and technical support
Warranty and service
This product is covered by warranty for 24 months after the day of purchase, provided that it has been operated in accordance with these instructions at the specified voltage and is not mechanically damaged. When claiming warranty repairs for the product, always attach proof of purchase. Warranty and post-warranty service is provided by your dealer or themanufacturer.
Technical support
In case you are not sure about the setup or some functions of the product,donot hesitate to contact our technical support. You can contact either your dealer or the manufacturer JETImodels, r.o..
- For further information, visit www.jetimodel.cz.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free-of-charge basis. Alternatively, in some countries, you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal
FCC
FCC and IC conformity:
PART 15:
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this \ device must accept any interference, including interference that may cause undesired operation of the device.
Declaration of Conformity
MORE INFORMATION
- JETImodels.r.o.
- Lomená 1530, 742 58 Příbor CzechRepublic-EU
- www.jetimodel.com
- info@jetimodel.cz
FAQs
- Q: How do I pair the COM PLEX RADIO CONTROL SYSTEM?
- A: Refer to section 1.1 “Pairing” in the manual for detailed instructions on pairing the system.
- Q: What are the dimensions of the RC Power Switch models?
- A: The dimensions of RCPS5 are 38 x 7 x 20 mm.
Documents / Resources
 | duplex RCPS10 2.4EX RC Power Switch [pdf] User Manual RCPS10, RCPS5, RCPS10 2.4EX RC Power Switch, RCPS10, 2.4EX RC Power Switch, Power Switch, Switch |