DREMEL-2200-VersaFlame-Cordless-Tool-Logo

DREMEL 2200 VersaFlame Cordless Tool

DREMEL-2200-VersaFlame-Cordless-Tool-Product

Introduction

To all residents of the European Union Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

  • Keep this device away from children and unauthorized users.
  • Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
  • Use the receiver indoors only. Keep away from rain, moisture, splashing, and dripping liquids.

General Guidelines

  • Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
  • Keep this device away from dust and extreme temperatures.

DREMEL-2200-VersaFlame-Cordless-Tool-Fig3

  • Protect this device from shocks and abuse. Avoid brute force when operating the device.

DREMEL-2200-VersaFlame-Cordless-Tool-Fig4

  • Familiarise yourself with the functions of the device before actually using it.
  • All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
  • Only use the device for its intended purpose. Using the device in an unauthorized way will void the warranty.
  • Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
  • Due to constant product improvements, the actual product appearance might differ from the shown images.
  • Product images are for illustrative purposes only.
  • Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature
  • Keep this manual for future reference.

Battery

Refer to the illustrations on page 2 of this manual.

Transmitter

  • Open the transmitter to reveal the battery compartment. Use a flat-head screwdriver.
  • Install the CR2032 battery according to the correct polarity.
  • Close the battery compartment. Proceed with the installation.

Receiver

  • Open the receiver to reveal the battery compartment.
  • Install 3 x 1.5 V AA batteries according to the correct polarity.
  • Close the battery compartment. Proceed with the installation.
  • Remark Remove the batteries if the transmitter and receiver will not be used for a longer period.

CAUTION

The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like. Do not puncture batteries or throw them on fire as they may explode. Do not attempt to recharge non-rechargeable batteries (alkaline). Dispose of batteries in accordance with local regulations. Keep batteries away from children.

Installation

  • Test the operating range between the receiver and the transmitter. The operating range is 150 m in the open air but may be less due to walls and other obstructions such as PVC or metal frames.
  • Refer to the illustrations on page 2 of this manual.

Transmitter

  • Carefully open the housing of the transmitter and use the backplate as a template. Mark the drilling holes at the required height.
  • Drill the holes using a drill and the appropriate drill bit (not included).
  • Insert a nylon plug (included) into each hole.
  • Fix the backplate with the included screws. Click the front plate onto the backplate.
  • Simply plug the receiver into the mains.

Receiver

  • Choose the installation spot for the receiver.
  • The receiver can be fixed to a wall using a hook or nail.
  • You can also fix the transmitter using double-sided tape.

Operation

  • Refer to the illustrations on page 2 of this manual.
  • Make sure both the receiver and transmitter are powered.
  • The receiver will ring when the button on the transmitter [1] is pressed.
  • Select the melody with the melody selector [4] and adjust the volume with volume control button [3].

Pairing

  1. On the receiver, hold the button pressed for 5 seconds until you hear a “ding-dong” sound.
  2. Now, press the transmitter button. The transmitter emits a “ding” sound to confirm successful pairing. The receiver emits a “ding-dong” sound when it exits the pairing mode.

Technical Specifications

frequency …………………………………………. 433.95 MHz
max. RF power ………………………………………….10 mW
wireless ………………………………………………………. yes
operating range ………………………… 150 m in an open area
self-learning …………………………………………………. yes
bell push…………………………………… with LED indicator
number of sounds …………………………………………… 32
IP rating (transmitter) …………………………………… IP44
power supply
transmitter ……………………………. 1 x CR2032 (incl.)
receiver ………………………….. 3 x 1.5 V AA (not incl.)

Use this device with original accessories only. Velleman Group NV cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.Velleman.EU. The information in this manual is subject to change without prior notice.

Documents / Resources

DREMEL 2200 VersaFlame Cordless Tool [pdf] Instruction Manual
2200, VersaFlame Cordless Tool, 2200 VersaFlame Cordless Tool

Leave a comment

Your email address will not be published.